首页> 外文OA文献 >Mixture Preparation and Combustion Variability in a Spray-Guided DISI Engine
【2h】

Mixture Preparation and Combustion Variability in a Spray-Guided DISI Engine

机译:喷雾引导DIsI发动机中的混合物制备和燃烧可变性

摘要

In an attempt to study the numerous contributors towards cyclic variations in combustion in a direct injection spark ignition engine, simultaneous high-speed imaging of fuel injection and flame growth are undertaken on a crank-angle resolved basis in a single-cylinder optical research engine. Batches of images from 100 consecutive cycles are acquired for all conditions with synchronised in-cylinder pressure logging. The engine is motored and fired at stoichiometric conditions at 1500 RPM under part-load and wide-open-throttle conditions (0.5-1.0 bar intake pressure), with injection timing set early in the intake stroke to promote homogeneous mixture formation with a centrally mounted multi-hole injector. Liquid impingement is observed on the cylinder walls and on the piston crown with early intake injection and multiple injection strategies are employed in an attempt to reduce impingement and alter mixture preparation and subsequent combustion. The effects are investigated for iso-octane and pump-grade gasoline at engine coolant temperatures of 50 and 90 °C. Gasoline sprays showed severe deformation and partial collapse of the individual spray plumes at 90 °C, leading to a different mixture formation process relative to iso-octane, which showed no such effects at this engine temperature. Using multiple fuel injections per cycle, but maintaining the same overall air-to-fuel ratio with single-injection strategies, a significant reduction in direct impingement on the walls was observed, together with different flame growth relative to single injection. These results suggest that injection strategy and type of fuel is playing an important role in the mixture preparation process, even for homogeneous early direct injection, and that different types of multiple-injection strategies alone have the potential to modify significantly in-cylinder phenomena, affect combustion and potentially exhaust emissions. Copyright © 2007 SAE International.
机译:为了研究导致直接喷射式火花点火发动机中燃烧循环变化的众多因素,在单缸光学研究发动机中,在曲轴转角解析的基础上对燃料喷射和火焰增长进行了同时高速成像。使用同步缸内压力记录功能,可在所有条件下获取来自100个连续周期的批次图像。发动机在部分负荷和节气门大开(进气压力0.5-1.0 bar)条件下以化学计量比和1500 RPM的功率进行点火,在进气冲程的早期设定喷射正时,以促进均匀混合气的形成。多孔注射器。通过早期进气喷射在汽缸壁和活塞顶上观察到液体撞击,并且采用多种喷射策略以试图减少撞击并改变混合物的制备和随后的燃烧。在发动机冷却液温度为50和90°C的情况下,研究了异辛烷和泵级汽油的影响。汽油喷雾剂在90°C时表现出严重的变形和单个喷雾羽流的部分塌陷,从而导致相对于异辛烷而言不同的混合物形成过程,在此发动机温度下没有这种作用。每个循环使用多次燃料喷射,但在单次喷射策略下保持相同的总空燃比,观察到直接撞击在壁上的显着减少,并且相对于单次喷射,火焰增长不同。这些结果表明,喷射策略和燃料类型在混合气制备过程中也起着重要作用,即使对于均质的早期直接喷射也是如此,而且仅单独使用不同类型的多次喷射策略就有可能显着改变缸内现象,燃烧和潜在的废气排放。版权所有©2007 SAE International。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号