...
首页> 外文期刊>International Journal of Solids and Structures >FAILURE CRITERION FOR MOISTURE-SENSITIVE PLASTIC PACKAGES OF INTEGRATED CIRCUIT (IC) DEVICES - APPLICATION OF VON-KARMANS EQUATIONS WITH CONSIDERATION OF THERMOELASTIC STRAINS
【24h】

FAILURE CRITERION FOR MOISTURE-SENSITIVE PLASTIC PACKAGES OF INTEGRATED CIRCUIT (IC) DEVICES - APPLICATION OF VON-KARMANS EQUATIONS WITH CONSIDERATION OF THERMOELASTIC STRAINS

机译:集成电路设备中对水分敏感的塑料包装的破坏准则-考虑热弹性应变的Von-Karmans方程的应用

获取原文
获取原文并翻译 | 示例
           

摘要

The maximum value of the von-Mises stress in the molding compound at the chip corner is suggested to be used as a suitable failure criterion for moisture-induced plastic packages of integrated circuit (IC) devices. This criterion is able to reflect the role of various geometric and materials characteristics affecting the package propensity to moisture-induced failures during high-temperature reflow soldering. It is suggested also that the von-Mises stress be determined from the constitutive equations which are a generalization of the von-Karman equations for large deflections of plates with consideration of thermoelastic strains. The generalized von-Karman equations are applied to the underchip layer of the molding compound and consider thermal effects associated with the thermal expansion (contraction) mismatch of the materials in the package, as well as with temperature gradients. The predicted stresses are in good agreement with experimental observations. The calculated von-Mises stresses can be used, particularly, for the development of ''Figures of Merit'' that would enable one to separate packages that need to be ''baked'' and ''bagged'' (or ''rebaked'' and ''rebagged'') from those that supposedly do not. The calculated stresses can be used also to judge whether the qualification test conditions for sufficiently reliable packages (say, thick packages with small chips) could be safely ''derated'' to an actual factory humidity profile. Finally, the calculated von-Mises stress can be helpful in the selection of the most feasible molding compound for the given package design. A more reliable (and more expensive) material might be needed in the case of a thin package with a large chip, while a low cost compound can be successfully employed in the case of a thick package with a small chip. (C) 1997 Elsevier Science Ltd. [References: 29]
机译:建议将芯片角处模塑料中的von-Mises应力最大值用作集成电路(IC)器件的湿气诱导塑料封装的合适失效准则。该标准能够反映出各种几何和材料特性的影响,这些特性会影响封装在高温回流焊过程中因水分引起的失效的倾向。还建议从本构方程确定von-Mises应力,本构方程是考虑了热弹性应变的板大挠度的von-Karman方程的推广。将通用的von-Karman方程应用于模塑料的芯片下层,并考虑与封装中材料的热膨胀(收缩)不匹配以及温度梯度相关的热效应。预测的应力与实验观察结果非常吻合。所计算出的von-Mises应力尤其可以用于开发“优点指标”,从而使人们能够分离需要“烘焙”和“装袋”(或“重新烘焙”)的包装”和“重新标记”)。计算出的应力还可以用于判断是否足够安全地将合格的包装(例如,带有小碎屑的厚包装)的合格测试条件安全地“降低”至实际的工厂湿度曲线。最后,对于给定的包装设计,计算出的von-Mises应力可能有助于选择最可行的模塑料。在具有大芯片的薄封装的情况下,可能需要更可靠(和更昂贵)的材料,而在具有小芯片的厚封装的情况下,可以成功地采用低成本的化合物。 (C)1997 Elsevier Science Ltd. [参考:29]

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号