首页> 外文期刊>Remote Sensing of Environment: An Interdisciplinary Journal >Single tree identification using airborne multibaseline SAR interferometry data
【24h】

Single tree identification using airborne multibaseline SAR interferometry data

机译:使用机载多基线SAR干涉数据识别单棵树

获取原文
获取原文并翻译 | 示例
获取外文期刊封面目录资料

摘要

Remote sensing data allow large scale observation of forested ecosystems. Forest assessment benefits from information about individual trees. Multibaseline SAR interferometry (InSAR) is able to generate dense point clouds of forest canopies, similar to airborne laser scanning (ALS). This type of point cloud was generated using data from the Ka-band MEMPHIS system, acquired over a mainly coniferous forest near Vordemwald in the Swiss Midlands. This point cloud was segmented using an advanced clustering technique to detect individual trees and derive their positions, heights, and crown diameters. To evaluate the InSAR point cloud properties and limitations, it was compared to products derived from ALS and stereo-photogrammetry. All point clouds showed similar geolocation accuracies with 02-0.3 m relative shifts. Both InSAR and photogrammetry techniques yielded points predominantly located in the upper levels of the forest vegetation, while ALS provided points from the top of the canopy down to the understory and forest floor. The canopy height models agreed very well with each other, with R-2 values between 0.84 and 0.89. The detected trees and their estimated physical and structural parameters were validated by comparing them to reference forestry data. A detection rate of similar to 90% was achieved for larger trees, corresponding to half of the reference trees. The smaller trees were detected with a success rate of similar to 50%. The tree height was slightly underestimated, with a R-2 value of 0.63. The estimated crown diameter agreed on an average sense, however with a relatively low R-2 value of 0.19. Very high success rates (>90%) were obtained when matching the trees detected from the InSAR-data with those detected from the ALS- and photogrammetry-data. There, InSAR tree heights were in the mean 1-1.5 m lower, with high R-2 values ranging between 0.8 and 0.9. Our results demonstrate the use of millimeter wave SAR interferometry data as an alternative to ALS- and photogrammetry-based data for forest monitoring. (C) 2016 Elsevier Inc. All rights reserved.
机译:遥感数据允许对森林生态系统进行大规模观察。森林评估受益于有关单个树木的信息。多基线SAR干涉仪(InSAR)能够生成森林冠层的密集点云,类似于机载激光扫描(ALS)。这种类型的点云是使用来自Ka波段MEMPHIS系统的数据生成的,该数据是在瑞士中部土地的Vordemwald附近主要是针叶林上采集的。使用先进的聚类技术对该点云进行分割,以检测单个树木并得出其位置,高度和树冠直径。为了评估InSAR点云的性质和局限性,将其与ALS和立体摄影测量法得出的产品进行了比较。所有点云都显示相似的地理位置精度,相对位移为02-0.3 m。 InSAR和摄影测量技术均产生的点主要位于森林植被的上层,而ALS提供了从树冠顶部到林下和林底的点。冠层高度模型彼此非常吻合,R-2值在0.84和0.89之间。通过将其与参考林业数据进行比较,可以验证检测到的树木及其估计的物理和结构参数。对于较大的树木,达到了大约90%的检测率,相当于参考树木的一半。检测到较小的树木,成功率接近50%。树的高度被低估了,R-2值为0.63。估计冠的直径在一般意义上是一致的,但是R-2值相对较低,为0.19。将InSAR数据中检测到的树木与ALS和摄影测量数据中检测到的树木进行匹配,可获得很高的成功率(> 90%)。在那里,InSAR树高平均降低了1-1.5 m,R-2的高值介于0.8和0.9之间。我们的结果表明,毫米波SAR干涉测量数据可替代基于ALS和摄影测量的数据进行森林监测。 (C)2016 Elsevier Inc.保留所有权利。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号