首页> 外文期刊>Particulate Science and Technology: An International Journal >Modeling of particle size distribution and energy consumption of wet milled maize at varying soaking period and method in the production of Ogi
【24h】

Modeling of particle size distribution and energy consumption of wet milled maize at varying soaking period and method in the production of Ogi

机译:改变浸泡期湿磨玉米粒度分布和能耗的建模及ogi

获取原文
获取原文并翻译 | 示例
           

摘要

Energy consumptions and particles size distribution of soaked maize grains at varying time were studied and modeled.Rosin-Rammler-Bennet(RRB) model well fitted first milling size distribution with a high coefficient of determination(R~2) and low root mean square error(RSME).The milling energy of maize grains decreased significantly(p < 0.05) with increase in soaking time.The milling energy decrease from 32 to 8.72 kWh/kg and 32.00 to 9.00 kWh/kg for maize variety E9W at 24th hour soaking conditions of 28 and 65°C,respectively.Similar observations for A4W,B2Y and C3Y at 24 h of soaking were recorded.The Work index,Kick's and Rittinger's constants decreased with increase in soaking time.There was significant difference(p < 0.05) in values obtained for Bond work index,Rittinger's and Kick's constants;these decreased with increase in soaking time.Predicted energy consumption followed similar trend.The interaction effect between energy consumption,Moisture content,and Milling time showed a high ft~2(0.8767-0.99349);while the regressed model for determining energy consumption from relationship between the mass,moisture content,milling time and the ratio of the geometric diameter mean and final size of the product were also established in this work with R2 ranging from 0.9355 to 0.967.
机译:研究了不同时间浸泡玉米晶粒的能量消耗和颗粒尺寸分布,并模拟了rOSIN-Rammler-ennet(RRB)模型井拟合的第一铣削尺寸分布,具有高系数(R〜2)和低根均方误差(rsme)。玉米谷物的铣削能量显着下降(p <0.05),浸泡时间增加。在第24小时浸泡条件下,铣削能量从32〜8.72千瓦时/千克和32.00至9.00千瓦时/千克。分别为28和65°C。记录了24小时的A4W,B2Y和C3Y的混合观察。作品指数,踢腿和频率的常数随着浸泡时间的增加而下降。有统计学意义(P <0.05)用于债券工作指数,Rittinger和Kick常量获得的值;这些随着浸泡时间的增加而减少。预测的能耗遵循类似的趋势。能耗,水分含量和铣削时间之间的相互作用效应显示高FT〜2(0.8767-0.99349);在这项工作中也建立了用于从质量,水分含量,铣削时间和几何直径平均值和最终尺寸的几何直径平均值和最终尺寸的关系中确定能量消耗的回归模型。 R2范围从0.9355到0.967。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号