首页> 外文期刊>Journal of toxicology and environmental health, Part A >Gene-expression profiling of human mononuclear cells from welders using cDNA microarray.
【24h】

Gene-expression profiling of human mononuclear cells from welders using cDNA microarray.

机译:使用cDNA芯片从焊工对人单核细胞进行基因表达谱分析。

获取原文
获取原文并翻译 | 示例
       

摘要

A toxicogenomic chip developed to detect welding-related diseases was tested and validated for field trials. To verify the suitability of the microarray, white blood cells (WBC) or whole blood was purified and characterized from 20 subjects in the control group (average work experience of 7 yr) and 20 welders in the welding-fume exposed group (welders with an average work experience of 23 yr). Two hundred and fifty-three rat genes homologous to human genes were obtained and spotted on the chip slide. Meanwhile, a human cDNA chip spotted with 8600 human genes was also used to detect any increased or decreased levels of gene expression among the welders. After comparing the levels of gene expression between the control and welder groups using the toxicogenomic chips, 103 genes were identified as likely to be specifically changed by welding-fume exposure. Eighteen of the 253 rat genes were specifically changed in the welders, while 103 genes from the human cDNA chip were specifically changed. The genes specifically expressed by the welders were associated with inflammatory responses, toxic chemical metabolism, stress proteins, transcription factors, and signal transduction. In contrast, there was no significant change in the genes related to short-term welding-fume exposure, such as tumor necrosis factor (TNF)-alpha and interleukin. In conclusion, if further validation studies are conducted, the present toxicogenomic gene chips could be used for the effective monitoring of welding-fume-exposure-related diseases among welders.
机译:测试并验证了开发用于检测焊接相关疾病的毒理基因组芯片以进行现场试验。为了验证微阵列的适用性,从对照组的20名受试者(平均工作经验为7年)和暴露于焊接烟气的组中的20名焊工(焊缝为23年的平均工作经验)。获得了与人类基因同源的253个大鼠基因,并将其点在芯片载玻片上。同时,点有8600个人类基因的人类cDNA芯片也用于检测焊工之间基因表达的任何升高或降低水平。在使用毒理基因组芯片比较了对照组和焊工组之间的基因表达水平后,确定了103种可能被焊烟暴露特异性改变的基因。在253个大鼠基因中,有18个在焊工中被专门改变,而来自人类cDNA芯片的103个基因被特别改变。焊工特别表达的基因与炎症反应,有毒化学代谢,应激蛋白,转录因子和信号转导有关。相反,与短期焊接烟雾接触有关的基因,例如肿瘤坏死因子(TNF)-α和白介素,没有显着变化。总之,如果进行进一步的验证研究,则当前的毒物基因组基因芯片可用于有效监测焊工中与焊接烟雾接触有关的疾病。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号