VERIFICATION OF THE STANDARD MACHINE FOR THE MACRO RANGE OF INSTRUMENTED INDENTATION TEST

机译：验证仪表缩进测试宏范围的标准机

获取原文

页面导航

摘要
著录项
相似文献
相关主题

摘要

A new calibration machine according to the requirements given by ISO 14577-3 [1] was described in [2]. The results of the verification are reported in this paper. It is shown that the calibration machine can be used as a national standard for the materials parameter of the instrumented indentation test.

机译：根据ISO 14577-3 [1]给出的要求，在[2]中描述了一种新的校准机。本文报告了验证结果。结果表明，校准机可用作仪表压痕试验材料参数的国家标准。

著录项

来源
《Symposium on Recent Advancements in the Theory and Practice of Hardness Measurement》|2009年||共5页
会议地点
作者
Harald Kohlhoff; Christian Ullner;
展开▼
作者单位

展开▼
会议组织
原文格式 PDF
正文语种
中图分类 TB926;
关键词
indentation; standard; verification;

机译：缩进;标准;验证;

相似文献

外文文献
中文文献
专利

1. Concrete and Quantitative Analyses on Instrumented Indentation Test (Proposal of new theory for determination procedures of optimum machine frame compliance in micro and macro test range of ISO 14577-1) [J] . Tatsuya Ishibashi, Yusuke Yoshikawa, Kensuke Miyahara, 材料試験技術 . 2016,第2期

机译：仪器压痕测试的具体和定量分析（关于在ISO 14577-1的微观和宏观测试范围内确定最佳机架符合性的确定程序的新理论的建议）
2. Effect and measurement of the machine compliance in the macro range of instrumented indentation test [J] . Christian Ullner, Erhard Reimann, Harald Kohlhoff, Measurement . 2010,第2期

机译：在仪器压痕测试的宏观范围内对机器顺应性的影响和测量
3. Proposal for ISO 14577-Part 1: Test method (Verification of the calculation method of Young's modulus for wide range of materials and test forces ranging from micro to macro range with data un-calibrated machine frame compliance in its testing system) [J] . Tatsuya ISHIBASHI, Yusuke YOSHIKAWA, Masayuki YAMAMOTO, 材料試験技術 . 2017,第3期

机译：提议 ISO 14577 第1部分：试验方法（杨氏模量为宽范围的材料和试验力范围从微观到宏观范围在其测试系统数据未校准的机架柔度的计算方法的确认）
4. VERIFICATION OF THE STANDARD MACHINE FOR THE MACRO RANGE OF INSTRUMENTED INDENTATION TEST [C] . Harald Kohlhoff, Christian Ullner Symposium on Recent Advancements in the Theory and Practice of Hardness Measurement . 2009

机译：验证仪表缩进测试宏范围的标准机
5. On the use of Raman spectroscopy and instrumented indentation for characterizing damage in machined carbide ceramics [D] . Groth, Benjamin Peter 2013

机译：关于使用拉曼光谱和仪器压痕来表征机械加工硬质合金的损伤
6. Mechanical properties of orthodontic wires derived by instrumented indentation testing (IIT) according to ISO 14577 [O] . Spiros Zinelis, Youssef S Al Jabbari, Marianna Gaintantzopoulou, 2015

机译：通过仪器压痕测试（IIT）根据ISO 14577得出的正畸钢丝的机械性能
7. Indentation Modulus, Indentation Work and Creep of Metals and Alloys at the Macro-Scale Level: Experimental Insights into the Use of a Primary Vickers Hardness Standard Machine [O] . Alessandro Schiavi, Claudio Origlia, Alessandro Germak, 2021

机译：宏观尺度水平的压痕模量，压痕工作和金属和合金的蠕变：实验见解使用主要维克斯硬度标准机器
8. Description of the Nano delta Indenter (R); An Ultra-Low-Load Microhardness Indentation Test Machine. [R] . Schmale, D. T., Bourcier, R. J. 1989

机译：Nano delta Indenter（R）的描述;超低负荷显微硬度压痕试验机。

VERIFICATION OF THE STANDARD MACHINE FOR THE MACRO RANGE OF INSTRUMENTED INDENTATION TEST

摘要

著录项

相似文献

相关主题

期刊订阅