ASTM D1280-14 Standard Guide for Total Immersion Corrosion Test for Soak Tank Metal Cleaners (Withdrawn 2023)

浸泡罐金属清洗剂总浸渍腐蚀试验标准指南

基本信息

标准号

ASTM D1280-14

标准状态

作废

发布单位或类别

美国-美国材料与试验协会(US-ASTM);

发布日期

实施日期

废止日期

CCS分类

ICS分类

71.100.40 化工产品 - 表面活性剂及其他助剂

研制信息

起草单位

- 展开▼

起草人

归口单位

D12.16

摘要

1.1This guide covers determination of the corrosive effects of soak tank metal cleaners on all metals other than aluminum and its alloys, under conditions of total immersion, by quantitative measurement of weight change or by qualitative visual determination of change. The test determines the effects of the cleaner on metals being cleaned, and does not determine the life of the cleaner or of the containing equipment.1.2When the test is used to assist in the choice of material for a specific use, the test conditions should simulate the conditions of use as closely as practicable.1.3Where no further processing subsequent to cleaning is indicated, a test for the effect of residual cleaner on the corrosion behavior of the material may be required.1.4The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage. ====== Significance And Use ======3.1This guide is used to distinguish soak tank metal cleaners that are excessively corrosive to metals (other than aluminum and its alloys which are covered by MethodD930). The users will define the degree of corrosion considered excessive, in terms of weight loss per unit of surface area or in terms of changes in appearance, or both. 1.1本指南涵盖了在全浸条件下，通过定量测量重量变化或定性目视测定变化，测定浸泡槽金属清洁剂对除铝及其合金以外的所有金属的腐蚀作用。该试验确定了清洁剂对被清洁金属的影响，但不确定清洁剂或容纳设备的寿命。1.2当测试用于帮助选择特定用途的材料时，测试条件应尽可能模拟使用条件。1.3如果清洁后未指示进一步处理，则可能需要测试残留清洁剂对材料腐蚀行为的影响。1.4以国际单位制表示的数值应视为标准值。括号中给出的值是英寸-磅单位的数学转换，仅供参考，不被视为标准值。1.5本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全和健康实践，并确定监管限制的适用性。试剂和材料有材料安全数据表。使用前检查其危险性。====意义和用途======3.1本指南用于区分对金属（方法覆盖的铝及其合金除外）具有过度腐蚀性的浸泡槽金属清洁剂D930). 用户将根据单位表面积的重量损失或外观变化或两者来定义被认为过度的腐蚀程度。展开▼

关联标准

代替如下标准

1.ASTM D1280-00(2007) Standard Guide for Total Immersion Corrosion Test for Soak Tank Metal Cleaners。

相似标准

1.Standard Guide for Total Immersion Corrosion Test for Soak Tank Metal Cleaners
机译：浸泡罐金属清洗剂总浸渍腐蚀试验标准指南
2.Standard Test Method for Total Immersion Corrosion Test for Soak Tank Metal Cleaners
机译：浸泡罐金属清洁剂全浸腐蚀试验的标准试验方法
3.Standard Test Method of Aerated Total Immersion Corrosion Test for Metal Cleaners (Withdrawn 2000)
机译：金属清洁剂充气全浸腐蚀试验的标准试验方法（2000年撤销）
4.Standard Test Method of Total Immersion Corrosion Test of Water-Soluble Aluminum Cleaners (Withdrawn 2001)
机译：水溶性铝清洁剂全浸腐蚀试验的标准试验方法（2001年撤销）
5.Standard Test Method of Aerated Total Immersion Corrosion Test for Metal Cleaners
机译：金属清洁剂充气全浸腐蚀试验的标准试验方法