ASTM F2159-11 Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环塑料插入件的标准规范

基本信息

标准号

ASTM F2159-11

标准状态

历史

发布单位或类别

美国-美国材料与试验协会(US-ASTM);

发布日期

实施日期

废止日期

CCS分类

ICS分类

23.040.45 管道部件和管道 - 塑料配件

研制信息

起草单位

- 展开▼

起草人

归口单位

F17.10

摘要

1.1 This specification establishes requirements for sulfone plastic insert fittings and copper crimp rings for four sizes(3/8,½, and¾and 1) of cross-linked polyethylene (PEX) plastic tubing an polyethylene of raised temperature (PE-RT) tubing. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180°F (82°C). Included are the requirements for material, molded part properties, performance, workmanship, dimensions, and markings to be used on the fittings and rings.1.2Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following is an index of the appendix in this specification:GO/NO-GO Crimp GaugesAppendix X11.4The following precautionary caveat pertains only to the test method portions, Sections 11 and 12, of this specification.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. 1.1本规范规定了四种尺寸的砜塑料插入配件和铜压接环的要求(3./8.,½和¾和1）交联聚乙烯（PEX）塑料管-高温聚乙烯（PE-RT）管。这些配件适用于100 psi（690 kPa）的冷水和热水分配系统，其工作温度高达180℃°F（82°C）。包括对配件和环上使用的材料、模塑件特性、性能、工艺、尺寸和标记的要求。1.2单位—以英寸-磅为单位的数值应视为标准值。括号中给出的值是到国际单位制的数学转换，仅供参考，不被视为标准值。1.3以下是本规范附录的索引:通/止压规附录X11.4以下预防性警告仅适用于本规范第11节和第12节的试验方法部分。本标准并非旨在解决与其使用相关的所有安全问题（如有）。本标准的用户有责任在使用前制定适当的安全和健康实践，并确定监管要求的适用性。展开▼

关联标准

代替如下标准

1.ASTM F2159-10 Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing。

被如下标准代替

1. ASTM F2159-14 Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing。

相似标准

1.Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
机译：SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环或替代不锈钢夹塑料插入件的标准规范
2.Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
机译：SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环塑料插入件的标准规范
3.Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
机译：SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环塑料插入件的标准规范
4.Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
机译：SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环塑料插入件的标准规范
5.Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
机译：SDR9交联聚乙烯（PEX）管和SDR9高温聚乙烯（PE-RT）管用铜压接环或备用不锈钢夹的金属插入配件标准规范