首页> 外文期刊>Journal of biomechanical engineering. >Development of a Model Based Method for Investigating Facet Articulation
【24h】

Development of a Model Based Method for Investigating Facet Articulation

机译:基于模型的小关节发音研究方法的开发

获取原文
获取原文并翻译 | 示例
           

摘要

Reported investigations of facet articulation in the human spine have often been conducted through the insertion of pressure sensitive film into the joint space, which requires incision of the facet capsule and may alter the characteristics of interaction between the facet surfaces. Load transmission through the facet has also been measured using strain gauges bonded to the articular processes. While this method allows for preservation of the facet capsule, it requires extensive instrumentation of the spine, as well as strain-gauge calibration, and is highly sensitive to placement and location of the strain gauges. The inherently invasive nature of these techniques makes it difficult to translate them into medical practice. A method has been developed to investigate facet articulation through the application of test kinematics to a specimen-specific rigid-body model of each vertebra within a lumbar spine segment. Rigid-body models of each vertebral body were developed from CT scans of each specimen. The distances between nearest-neighboring points on each facet surface were calculated for specific time frames of each specimen's flexion/extension test. A metric describing the proportion of each facet surface within a distance (2 mm) from the neighboring surface, the contact area ratio (CAR), was calculated at each of these time frames. A statistically significant difference (p <0.037) was found in the CAR between the time frames corresponding to full flexion and full extension in every level of the lumbar spine (L1-L5) using the data obtained from the seven specimens evaluated in this study. The finding that the contact area of the facet is greater in extension than flexion corresponds to other findings in the literature, as well as the generally accepted role of the facets in extension. Thus, a biomechanical method with a sufficiently sensitive metric is presented as a means to evaluate differences in facet articulation between intact and treated or between healthy and pathologic spines.
机译:人们通常通过将压敏薄膜插入关节空间来进行对人体脊柱小关节运动的研究,这需要切开小关节囊并且可能会改变小关节表面之间的相互作用特性。还使用与关节突相连的应变仪测量了通过小平面的载荷传递。尽管此方法可以保留小平面囊,但它需要对脊柱进行广泛的仪器安装以及应变仪校准,并且对应变仪的放置和位置高度敏感。这些技术的固有侵入性使其难以将其转化为医学实践。已经开发出一种方法,通过将测试运动学应用于腰椎节段内每个椎骨的标本特有的刚体模型,来研究刻面的关节运动。通过每个标本的CT扫描建立每个椎体的刚体模型。针对每个样本的屈曲/延伸测试的特定时间范围,计算出每个小平面上最近邻点之间的距离。在每个这些时间范围内,计算出一个度量值,该度量值描述了距相邻表面距离(2毫米)内每个小平面的比例,接触面积比(CAR)。使用从本研究评估的七个标本中获得的数据,在腰椎各个水平(L1-L5)对应于完全弯曲和完全伸展的时间范围之间,CAR的统计学差异显着(p <0.037)。小平面的接触区域在伸展上大于屈曲的发现与文献中的其他发现以及小平面在伸展中的公认作用相对应。因此,提出了一种具有足够灵敏度量的生物力学方法,作为评估完整脊椎和治疗脊椎之间或健康脊椎和病理脊椎之间的小关节运动差异的一种手段。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号