首页> 外文期刊>International Journal of Applied Ceramic Technology / Functional Ceramics >Fabrication of Nitrogen-Containing Cordierite Ceramics
【24h】

Fabrication of Nitrogen-Containing Cordierite Ceramics

机译:含氮堇青石陶瓷的制备

获取原文
获取原文并翻译 | 示例
       

摘要

We have investigated the crystallization behavior of cordierite-based oxynitride glass prepared by melting a powder mixture of cordierite and silicon nitride. The results indicated that two polymorphs exist: a stable a-form, which has a low coefficient of thermal expansion, and a metastable μ-form. The time-temperature-transformation diagram of the crystallization of the α-form shows a typical C-shaped curve that has a nose around 1420 K. Above 1373 K, the α-form can be directly obtained by the isothermal crystallization of the oxynitride glass and the μ-form inverts to the α-form at temperatures below 1273 K. We also have fabricated an α-cordierite ceramic that has a nitrogen content of 1.55 mass%, which is much lower than the content of the batch composition (5 mass%); this is mainly owing to the decomposition reaction of nitrogen in the oxynitride melts and glasses during heat treatment. However, the fabricated nitrogen-containing α-cordierite ceramics showed the coefficient of thermal expansion of 10~(-7) K~(-1) which is comparable with that of the oxide α-cordierite ceramics. Moreover, Young's modulus of the α-cordierite ceramics improved with the incorporation of nitrogen.
机译:我们已经研究了通过熔化堇青石和氮化硅的粉末混合物制备的堇青石基氧氮化物玻璃的结晶行为。结果表明存在两种多晶型物:具有低热膨胀系数的稳定的α-形式和亚稳态的μ-形式。 α-型结晶的时间-温度-转变图显示出典型的C形曲线,其鼻子在1420 K附近。在1373 K以上,α-型可以通过氧氮化玻璃的等温结晶直接获得。并且在低于1273 K的温度下μ形式转变为α形式。我们还制造了α堇青石陶瓷,其氮含量为1.55质量%,远低于批料成分(5质量%)的含量。 %);这主要是由于热处理过程中氮氧化物在熔体和玻璃中的分解反应所致。然而,所制备的含氮α-堇青石陶瓷的热膨胀系数为10〜(-7)K〜(-1),与氧化物α-堇青石陶瓷相当。此外,随着氮的掺入,α-堇青石陶瓷的杨氏模量提高。

著录项

  • 来源
  • 作者单位

    Department of Materials Science and Engineering, Kyushu University, Fukuoka 819-0395, Japan;

    Department of Materials Science and Engineering, Kyushu University, Fukuoka 819-0395, Japan;

    Department of Materials Science and Engineering, Kyushu University, Fukuoka 819-0395, Japan;

    Department of Materials Science and Engineering, Kyushu University, Fukuoka 819-0395, Japan;

    Department of Materials Science and Engineering, Kyushu University, Fukuoka 819-0395, Japan;

    Department of Materials Science and Engineering, Kyushu University, Fukuoka 819-0395, Japan;

    Nippon Tungsten Co. Ltd., Fukuoka 812-8538, Japan;

  • 收录信息 美国《科学引文索引》(SCI);美国《工程索引》(EI);美国《生物学医学文摘》(MEDLINE);
  • 原文格式 PDF
  • 正文语种 eng
  • 中图分类
  • 关键词

  • 入库时间 2022-08-17 13:40:36

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号