...
首页> 外文期刊>Arthroscopy: the journal of arthroscopic & related surgery : official publication of the Arthroscopy Association of North America and the International Arthroscopy Association >Femoral tunnel drilling angles for the posterolateral corner in multiligamentary knee reconstructions: Computed tomography evaluation in a cadaveric model
【24h】

Femoral tunnel drilling angles for the posterolateral corner in multiligamentary knee reconstructions: Computed tomography evaluation in a cadaveric model

机译:多韧带膝关节重建中后外侧角的股骨隧道钻孔角度:尸体模型中的计算机断层扫描评估

获取原文
获取原文并翻译 | 示例
           

摘要

Purpose: The goal of this study was to determine the best angle at which to drill the femoral tunnels of the popliteus tendon (PT) and fibular collateral ligament (FCL) in combined reconstructive procedures so as to avoid either short tunnels or tunnel collisions with the anterior cruciate ligament (ACL) and posterior cruciate ligament (PCL) femoral tunnels. Methods: Eight cadaveric knees were studied. ACL/PCL femoral tunnels were arthroscopically drilled. PT and FCL tunnels were drilled at 0° and 30° axial and coronal angulations. They were scanned by computed tomography to document relations of the PT and FCL tunnels to the intercondylar notch and ACL/PCL tunnels. A minimum tunnel length of 25 mm was required. Results: Drilling the PT tunnel at 0° axial angulation was associated with an increased risk of tunnel collision with the ACL (P <.001). Interference with the PCL tunnel can be avoided only if the K-wire guiding the PT tunnel is drilled with 30° coronal angulations (P <.001). The minimum tunnel length of the PT could be obtained only with both axial and coronal angulations of 30° (P =.003). Sufficient tunnel lengths of the FCL were obtained at all angulations evaluated (P =.036). However, only the tunnels drilled at 30° axial and 0° coronal angulations did not collapse with the ACL tunnels (P <.001). No intersections between FCL and PT tunnels were observed. Conclusions: When posterolateral reconstructions are performed in combination with concomitant anterior and posterior cruciate procedures, PT tunnels should be drilled at 30° axial and 30° coronal angulations. FCL tunnels should be drilled at 30° axial and 0° coronal angulations. These angulations should minimize such potential complications as short tunnels or collisions with the ACL/PCL tunnels. Clinical Relevance: Specific drilling angles are necessary to avoid short tunnels or collisions between the drilled tunnels when FCL and PT femoral tunnels are performed in multiligament knee reconstructions.
机译:目的:本研究的目的是确定在联合重建程序中钻出pop肌腱(PT)和腓骨副韧带(FCL)股骨隧道的最佳角度,以避免短隧道或隧道与股骨假体碰撞前交叉韧带(ACL)和后交叉韧带(PCL)股骨隧道。方法:研究八个尸体膝盖。关节镜下钻孔ACL / PCL股骨隧道。 PT和FCL隧道分别在0°和30°的轴向和日冕角度下钻孔。通过计算机断层扫描对其进行扫描,以记录PT和FCL隧道与con间切口和ACL / PCL隧道的关系。最小隧道长度为25 mm。结果:在0°轴向角上钻PT隧道与ACL发生隧道碰撞的风险增加相关(P <.001)。只有在引导PT隧道的K线钻有30°冠状角时才可以避免与PCL隧道的干扰(P <.001)。 PT的最小隧道长度只能在轴向和冠状角均为30°的情况下获得(P = .003)。在所有评估的角度下,都获得了足够的FCL隧道长度(P = .036)。但是,只有以30°轴向角和0°冠状角度钻出的隧道才不会因ACL隧道而塌陷(P <.001)。在FCL和PT隧道之间没有观察到交叉点。结论:当结合后外侧交叉手术进行后外侧重建时,应在轴向30°和冠状角30°处钻探PT隧道。 FCL隧道应在30°轴向角和0°冠状角下钻孔。这些角度应将诸如短隧道或与ACL / PCL隧道碰撞之类的潜在复杂性降至最低。临床意义:当在多韧带膝关节重建术中进行FCL和PT股骨隧道时,必须有特定的钻孔角度以避免短隧道或钻孔隧道之间发生碰撞。

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号