首页> 外文期刊>International Journal of Metalcasting: Leading the Transfer of Research and Technology for the Global Metalcasting Industry >Effects of Carbon Balance and Heat Treatment on Hardness and Volume Fraction of Retained Austenite of Semi-multi-alloyed White Cast Iron
【24h】

Effects of Carbon Balance and Heat Treatment on Hardness and Volume Fraction of Retained Austenite of Semi-multi-alloyed White Cast Iron

机译:碳平衡与热处理对半多合金白铸铁保留奥氏体硬度和体积分数的影响

获取原文
获取原文并翻译 | 示例
           

摘要

The heat treatment behavior of semi-multi-alloyed white cast iron with relatively lower carbide-forming elements compared with regular multi-alloyed white cast iron was investigated. The semi-multi-alloyed white cast iron with carbon balance (C-bal) of - 0.68 to + 0.53 wt% was prepared by varying chromium (Cr) content from around 3-9 wt% under the fixed contents of 2 wt% molybdenum (Mo), 1 wt% tungsten (W) and 5 wt% vanadium (V). After annealing, the test specimens were hardened after austenitizing at 1050 degrees C and 1100 degrees C. The tempering was carried out between 400 and 600 degrees C. In as-hardened state, the macro-hardness and micro-hardness increased greatly as the C-bal rose from - 0.68 to - 0.01 wt% and then decreased gradually with an increase in the C-bal value. The volume fraction of retained austenite (V-gamma) increased continuously as the C-bal increased, and more V-gamma was obtained in the case of hardening from higher austenitizing temperature. In tempered state, the hardness curve showed an evident secondary hardening due to the precipitation of fine secondary carbides during holding and the transformation of retained austenite to martensite during post-cooling. The maximum tempered macro-hardness (H-Tmax) was obtained by tempering at 500-550 degrees C. The highest values, 862 HV30 and 795 HV0.1, were obtained in the specimen with - 0.01 wt%C-bal where the V-gamma was about 2%. As the C-bal value increased, the maximum tempered micro-hardness (HTmax-M) increased remarkably toward - 0.01 wt%C-bal and then it decreased regardless of austenitizing temperature. At the same C-bal value, the HTmax-M of specimens hardened from 1100 degrees C were larger than those hardened from 1050 degrees C. It was found that the 10-50% V-gamma in as-hardened state was necessary to obtain hardness over 800 HV30 and 750 HV0.1 by tempering. The degree of secondary hardening (Delta Hs) increased with an increase in the C-bal and the V-gamma in the as-hardened state.
机译:研究了与常规多合金白铸铁相比,具有相对较低的碳化物成形元素的半多合金白色铸铁的热处理行为。通过在2wt%钼的固定含量下,通过在2wt%钼的固定含量下,通过在2wt%的固定含量为约3-9wt%的碳平衡(C-BAL)的半多合金白色铸铁 - 0.68至+ 0.53wt% (Mo),1wt%钨(W)和5wt%钒(V)。退火后,在1050℃和1100℃的奥氏体化后,试样硬化。在400-600℃之间进行回火在以硬化状态下进行,宏观硬度和微硬度大大增加为C. -BAL从 - 0.68至-0.01wt%上升,然后随着C-BAL值的增加而逐渐降低。保留奥氏体(V-Gamma)的体积分数连续增加,随着C-BAL的增加,在高奥氏体化温度的情况下获得更多V-γ。在钢化状态下,硬度曲线由于在冷却后沉淀过程中,由于在保持期间的细次级碳化物沉淀而沉淀出明显的第二硬化。通过以500-550℃的回火来获得最大钢化宏观硬度(H-Tmax)。在标本中获得最高值862HV30和795 HV0.1 - 0.01wt%C-BAL的样品-Gamma约为2%。随着C-BAL值的增加,最大钢化微硬度(HTMAX-M)显着朝向 - 0.01wt%C-BAL增加,然后无论奥氏体化温度如何降低。在相同的C-BAL值下,从1100℃硬化的样品HTMAX-M大于1050℃的硬化的样品的HTMAX-M.发现它是必要的10-50%V-GAMMA以获得通过回火超过800 HV30和750 HV0.1的硬度。二次硬化程度(Delta HS)随着C-BAL和v-γ的增加而增加的级别的状态。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号