...
首页> 外文期刊>Applied bionics and biomechanics >Measurement of Flexion Angle of the Finger Joint during Cylinder Gripping Using a Three-Dimensional Bone Model Built by X-Ray Computed Tomography
【24h】

Measurement of Flexion Angle of the Finger Joint during Cylinder Gripping Using a Three-Dimensional Bone Model Built by X-Ray Computed Tomography

机译:使用X射线计算机断层扫描构建的三维骨模型测量手指接头弯曲角度

获取原文
           

摘要

Motion analysis of the thumb and the four fingers during human gripping of a cylindrical object is a prerequisite for designing motion mechanisms in electronic arm prostheses and robotic hands. Conventional measurement methods include the use of angle sensors or multiple video recording of markers. In the present study, we performed X-ray computed tomography (CT) imaging on fingers gripping cylinders of three different diameters (10, 60, and 120?mm) and constructed a bone model based on these CT images to directly measure the flexion angle of each finger joint. We then compared the results with the flexion angles of joints measured using other methods. The subjects comprised 10 Japanese men with no hand injuries or diseases. Our results showed that smaller cylinder diameters were associated with significant increases in the flexion angle of all the joints of the four fingers. When focusing on the distal interphalangeal joint (DIP), there was no significant difference between any of the fingers for each of the cylinders, except between the index and middle fingers for the 10?mm-diameter cylinder. When focusing on the 10?mm-diameter cylinder, the flexion angle of the proximal interphalangeal joint (PIP) of each finger was significantly larger than that of the DIP and metacarpophalangeal joint (MP). However, no such significant difference was noted for the 120?mm-diameter cylinder. The coupling ratio (CR), which is the ratio of the flexion angles of the DIP and PIP, was significantly smaller for the 10?mm-diameter cylinder than for the 60?mm-diameter cylinder. However, there were no significant differences in CR between any of the fingers. A comparison of our study results with those derived using other methods indicated quantitative consistency for the DIP and PIP. However, for the MP, we noted differences that may be explained by the difficulty in determining the longitudinal axis of the metacarpal using other methods.
机译:拇指和四个手指在人类抓握过程中的运动分析是设计电子手臂假体和机器人手中的运动机制的先决条件。传统的测量方法包括使用角度传感器或标记的多个视频记录。在本研究中,我们在手指上进行了X射线计算机断层扫描(CT)成像,夹持三个不同直径(10,60和120Ωmm)的夹持圆柱,并基于这些CT图像构建骨模型,以直接测量屈曲角度每个手指接头。然后,我们将结果与使用其他方法测量的接头的屈曲角进行比较。受试者包含10名日本男性,没有手伤或疾病。我们的研究结果表明,较小的圆柱体直径与四个手指所有关节的屈曲角度显着增加。在关注远端间关节(DIP)时,每个气缸的任何手指之间没有显着差异,除了10毫米圆柱的指数和中间手指之间。在聚焦在10×Mm直径的圆柱体上时,每个手指的近端间骨髓间接头(PIP)的屈曲角度显着大于浸渍和肌曲腭关节(MP)的屈曲角度。但是,对于120毫米圆柱体没有注意这种显着差异。耦合比(Cr),即倾斜和pip的屈曲角度的比率比为60×mm - 直径的圆筒的圆筒显着更小。然而,任何手指之间的Cr都没有显着差异。我们的研究结果与使用其他方法衍生的研究结果进行了比较,表明了DIP和PIP的定量一致性。然而,对于MP,我们注意到可以通过使用其他方法确定核心轴的纵向轴线来解释的差异。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号