method of producing a deep and continuous druckmusters in thick textilgut and establishment of its implementation

• 1. 一种利用相转移催化剂实现直接生产ECH连续生产工业方法的建立浓度梯度的开车方法 [P] . 中国专利： CN109776456A . 2019-05-21
• 2. 一种连续深浮雕非球面微透镜阵列制作方法 [P] . 中国专利： CN100343698C . 2007.10.17
• 3. method of producing a deep and continuous druckmusters in thick textilgut and establishment of its implementation [P] . 法国专利： FR2191481A5 . 1974-02-01

  机译： 于深厚的绒毛的深而连续的鸭嘴兽的制作方法及其实现方法的建立

• 4. method of producing a deep and continuous druckmusters in thick textilgut and establishment of its implementation [P] . DD104576A5 . 1974-03-12

  机译： 于深厚的绒毛的深而连续的鸭嘴兽的制作方法及其实现方法的建立

• 5. method of producing a deep and continuous druckmusters in thick textilgut and establishment of its implementation [P] . 日本专利： JPS4948985A . 1974-05-11

  机译： 于深厚的绒毛的深而连续的鸭嘴兽的制作方法及其实现方法的建立

• 1. Research and implementation of continuous wave radar ranging method based on tri-frequency [J] . Yuan Qiping, Fan Lijie, Tong Zhengrong, 高技术通讯（英文版） . 2014,第002期
• 2. Comparative study of mining methods for reserves beneath end slope in flat surface mines with ultra-thick coal seams [J] . Zha Zhengao, Ma Li, Li Kemin, 矿业科学技术（英文版） . 2017,第006期
• 3. ESTABLISHMENT OF CREEP-FATIGUE DAMAGE EVALUATION AND NON-DISTRACTIVE TESTING METHODS FOR THICK WALL BOILER COMPONENT OF 2.25Cr-1 Mo STEEL [C] . Masashi Nakashiro, Takashi Yoshida, Yoshihiko Sakai, Joint ASME/JSME Pressure Vessels and Piping Conference . 1995
• 4. Implementation and microbial verification of HACCP (Hazard Analysis and Critical Control Point) systems and HACCP intervention methods in meat processing establishments for the reduction of foodborne pathogens. [D] . Dormedy, Erin Stafford. 1999
• 5. Cracking and segregation in high-alloy steel 0.4C1.5Mn2Cr0.35Mo1.5Ni produced by thick continuous casting [O] . Rensheng Chu, Zhanjun Li, Yong Fan, 2019
• 6. This article presents a new numerical model describing the behaviour of a thermally thick wood sample exposed to high solar heat flux (above 1 MW/m2). A preliminary study based on dimensionless numbers is used to classify the problem and support model building assumptions. Then, a model based on mass, momentum and energy balance equations is proposed. These equations are coupled with liquid-vapour drying model and pseudo species biomass degradation model. By comparing to a former experimental study, preliminary results have shown that these equations are not enough to accurately predict biomass behaviour under high solar heat flux. Indeed, a char layer acting as radiative shield forms on the sample exposed surface. In addition to this classical set of equations, it is mandatory to take into account radiation penetration into the medium. Furthermore, as biomass contains water, medium deformation consecutively to char steam gasification must also be implemented. Finally, with the addition of these two strategies, the model is able to properly capture the degradation of biomass when exposed to high radiative heat flux over a range of sample initial moisture content. Additional insights of biomass behaviour under high solar heat flux were also derived. Drying, pyrolysis and gasification fronts are present at the same time inside of the sample. The coexistence of these three thermochemical fronts leads to char gasification by the steam produced from drying of the sample, which it is the main phenomenon behind medium ablation. [O] . Pozzobon, Victor, Salvador, Sylvain, Bézian, Jean Jacques 2018
• 7. Manufacturing Methods and Technology Engineering (MM&TE) Program for the Establishment of Production Techniques for High Density Thick Film Circuits Used in Crystal Oscillators. Volume I [R] . Zilberstein, R. M. 1980

• 1. Feasibility Study on Continuous Mining Method in Deep Position of Jinchuan Nickel Mine, China [J] . . 矿物冶金与材料学报 . 2001,第002期
• 2. A Comparison Study of Deep Galerkin Method and Deep Ritz Method for Elliptic Problems with Different Boundary Conditions [J] . Jingrun Chen ,Rui Dul ,Keke Wu . 数学研究通讯 . 2020,第003期
• 3. Examination of Treatment Methods for a PEDOT:PSS Transparent Conductive Film Produced Using an Inkjet Method [J] . Atsushi Nitta ,Yuki Imamura ,Kazuya Kawahara . 材料物理与化学进展（英文） . 2017,第8期
• 4. 新型血脑屏障模型的建立一种新型微孔底膜插入式培养皿的制作方法 [C] . 赵康峰 ,蒲小平 ,杨秀伟 . 中国药学会学术年会 . 2004
• 5. 一种高产组织芯片制作方法的建立、应用与转化 [A] . 何德明 . 2013