首页> 外国专利> Portable type Machine for making Snow Brand consulbar turbofan

Portable type Machine for making Snow Brand consulbar turbofan

机译:造雪机品牌领事涡轮风扇的便携式机器

摘要

Fabrication of the prototype Machine of Argentine industry to build Snow Blower type. A transportable Chassis consists of a Cylinder which is mounted on the Conical Plate with a u-shaped bracket 360s tour on the chassis.To turn on its Axis average cross-section has two Side brackets that allow Tilt vertically at an angle from the horizontal of 56s. In its interior operates a 16 Blade adjustable axial Propeller, driven by an electric motor 15 HP with a maximum speed of 1440 rpm.At the end of smaller diameter or u00f4salidau00f6 is a module of sprinklers - variable quantity between 24 and 32 - to spray water on the natural pre pressurized Air Flow generated by the Canon, forming Cloud droplets of 400 to 700 microM, which during his career in medi Or below zero Environment, crystallize as precipitating Snow Crystal.The pressure of work requires a minimum of 8 bar and supports up to 35 bar. Maximum performance is obtained between 18 and 30 bar.Part of the module, the u00f4nucleadoresu00f6 Peaks or Initiators, with a mixture of water / air / Oxygen or water are the shapers of the first Crystals are projected on the flow generated by the sprinklers and by contagion to the rest of the solidified droplets projected Mass.The required Compressed Air Compressor, is provided by a Bi Cylindrical, soundproof, Constant Flow pressure of 10 bar and a production of 300 litres / minute. The compressor motor is Three Phase 5.5 HP.The Water Supply is from an external Network - previously pressurized - and enter the Canon through a high-pressure Hose / S / n the Hydrant which connects to the Machine. The diameter of Hose and coupling of entrance is 50 mm.Water becomes a Quick Filter with Stainless Steel Mesh and from there to a Distribution Chamber below which are the Fares are excluded from each Circuit. Feeding the Initiators is performed through a 12.7 mm, Feeding the sprinklers with major Drivers of 25 mm. And in the module by Connecting hoses of 12.7 mm.The Electric Power is 380 W enters flexible cable to board general Controls. The estimated consumption of Resistance heating, Motors, Lights, Alarm is located in 18 kW / hour. The Dashboard contains: on / off switches, Indicator Lights: red, Yellow, Green Keys; Thermal Protection; Readers; contactors; phases; fuses; Hour Meter; etc.
机译:制造阿根廷工业原型机以制造吹雪机类型。便携式底盘由安装在圆锥板上的圆柱体组成,底盘上有一个u形支架360s环。要打开其轴的平均横截面,它有两个侧面支架,可让其垂直于水平方向倾斜一个角度。 56多岁在其内部装有一个16叶片可调轴向螺旋桨,由15 HP电动机驱动,最大速度为1440 rpm。在较小直径或 u00f4salida u00f6末端是一个喷头模块-数量在24到32之间-在佳能产生的自然预加压气流上喷水,形成400到700 microM的云滴,在他的职业生涯中(在中等或零环境以下)结晶为沉淀雪晶。工作压力至少需要8 bar,最高支持35 bar。在18至30 bar的压力下可获得最佳性能。模块的一部分,峰或引发剂以及水/空气/氧气或水的混合物是第一个晶体的整形器,投射在产生的气流上通过洒水喷头并通过接触其他凝固的液滴投射出质量。所需的压缩空气压缩机由双圆柱,隔音,恒定流量10 bar提供,产量为300升/分钟。压缩机电机为三相5.5 HP。供水来自外部网络-事先已加压-并通过与机器连接的高压消火栓// S / n进入佳能。软管的直径和入口接头的直径为50毫米。水成为带有不锈钢网的快速过滤器,并从那里到分配室,在该分配室的下面,每个回路都不含票价。通过12.7 mm进料引发剂,使用25 mm的主要驱动器进料洒水喷头。并在模块中通过连接12.7 mm的软管。功率为380 W,输入挠性电缆连接到板上的通用控件。电阻加热,电动机,电灯,警报器的估计消耗量为18 kW /小时。仪表板包含:开/关开关,指示灯:红色,黄色,绿色键;热保护;读者;接触器阶段保险丝;计时器;等等

著录项

  • 公开/公告号AR049688A4

    专利类型

  • 公开/公告日2006-08-30

    原文格式PDF

  • 申请/专利权人 PERICOLA GUILLERMO ARTURO;

    申请/专利号AR2005M101741

  • 发明设计人

    申请日2005-05-02

  • 分类号F25C3/04;

  • 国家 AR

  • 入库时间 2022-08-21 21:40:28

相似文献

  • 专利
  • 外文文献
  • 中文文献
获取专利

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号