'Some rotomoulders are just full of HOT AIR OR 'THE CAUSE AND EFFECT OF POORLY VENTED MOULDS'.

Gareth McDowell

首页> 外文期刊>Rotoworld: magazine for the rotational molding & plastics design industries >'Some rotomoulders are just full of HOT AIR OR 'THE CAUSE AND EFFECT OF POORLY VENTED MOULDS'.

【24h】

'Some rotomoulders are just full of HOT AIR OR 'THE CAUSE AND EFFECT OF POORLY VENTED MOULDS'.

机译：“有些转轮动物只是充满了热空气，或者是“通风不良的模具的起因和作用”。

获取原文

获取原文并翻译 | 示例

获取外文期刊封面封底 >>

开具论文收录证明 >>

文献代查 >>

页面导航

摘要
著录项
相似文献
相关主题

摘要

In no particular order the typical issues that caused scrap and general grimacing were: shrinkage and warping (uncontrolled); under cure and over cure; wrong materials/ colours; wrong shot weight; missing nutserts; machine faults; contamination and pin-holing.

机译：造成报废和普遍卡住的典型问题没有特别的顺序：收缩和翘曲（不受控制）;治愈不足和过度治愈;材料/颜色错误;射重错误;缺少坚果;机器故障;污染和针孔。

著录项

来源
《Rotoworld: magazine for the rotational molding & plastics design industries》 |2015年第2期|共2页
作者
Gareth McDowell;
展开▼
作者单位

展开▼
收录信息
原文格式 PDF
正文语种 eng
中图分类合成树脂与塑料工业;
关键词

相似文献

外文文献
中文文献
专利

1. "Some rotomoulders are just full of HOT AIR OR "THE CAUSE AND EFFECT OF POORLY VENTED MOULDS". [J] . Gareth McDowell Rotoworld: magazine for the rotational molding & plastics design industries . 2015,第2期

机译：“有些转轮动物只是充满了热空气，或者是“通风不良的模具的起因和作用”。
2. Effects of equivalence ratio, thickness of rupture membrane and vent area on vented hydrogen-air deflagrations in an end-vented duct with an obstacle [J] . Zhang Su, Tang Zesi, Li Jialin, International journal of hydrogen energy . 2019,第47期

机译：当量比，破裂膜厚度和排气面积对带有障碍物的末端通气管道中氢气-空气爆燃的影响
3. Allied Moulded Products, Inc. offers NEMA 4X vent kit for electrical enclosures [J] . Electrical India . 2017,第5期

机译：联合模塑产品有限公司提供用于电气外壳的NEMA 4X通风套件
4. Modelling of the Effects of Mould Venting on the Injection Moulding Process [C] . D.M. Gao, S. Reymond, J.F. Hetu, Conference Proceedings at ANTEC '98 . 1998

机译：模具排气对注塑过程影响的建模
5. The structural use of hot press moulded glass reinforced polyester [D] . Mallin, Graham Michael. 1984

机译：热压模制玻璃纤维增强聚酯的结构用途
6. High Temperature Adiabatic Heating in µ-IM Mould Cavities—A Case for Venting Design Solutions [O] . Matthew Tucker, Christian A. Griffiths, Andrew Rees, 2020

机译：µ-IM模具型腔中的高温绝热加热—通风设计解决方案的案例
7. DESCRIPTION AND VERIFICATION BY EXPERIMENTS OF CRITICAL CONDITION FOR ONSET OF AIR ENTRAINMENT INTO MECHANICAL SMOKE VENT FROM LOWER AIR : Formulation of air entrainment into mechanical smoke vent opening for two-layer zone model Part1 [O] . Daisaku NII, Kazunori HARADA 2003

机译：通过降低空气夹风的空气夹风的临界条件的描述和验证：用于双层区域模型的机械烟雾通风口的空气夹带的配方
8. Venting of Noncondensible Gas from the Upper Head of a B and W Reactor Vessel Using Hot Leg U-Bend Vent Valves. [R] . Waterman, M. E., Kullberg, C. M., Wheatley, P. D. 1986

机译：使用热腿U形弯曲排气阀从B和W反应器容器的上部顶部排出不可冷凝气体。

'Some rotomoulders are just full of HOT AIR OR 'THE CAUSE AND EFFECT OF POORLY VENTED MOULDS'.

摘要

著录项

相似文献

相关主题

期刊订阅