首页> 外文期刊>New astronomy >Formation of high mass X-ray black hole binaries
【24h】

Formation of high mass X-ray black hole binaries

机译:高质量X射线黑洞双星的形成

获取原文
获取原文并翻译 | 示例
       

摘要

The discrepancy in the past years of many more black-hole soft X-ray transients (SXTs), of which a dozen have now been identified, had challenged accepted wisdom in black hole evolution. Reconstruction in the literature of high-mass X-ray binaries has required stars of up to ~ 40 M_⊙ to evolve into low-mass compact objects, setting this mass as the limit often used for black hole formation in population syntheses. On the other hand, the sheer number of inferred SXTs requires that many, if not most, stars of ZAMS masses 20-35 M_⊙ end up as black holes (Portegies Zwart et al., 1997; Ergma and van den Heuvel, 1998). In this paper we show that this can be understood by challenging the accepted wisdom that the result of helium core burning in a massive star is independent of whether the core is covered by a hydrogen envelope, or 'naked' while it burns. The latter case occurs in binaries when the envelope of envelope of the more massive star is transferred to the companion by Roche Lobe overflow while in either main sequence or red giant stage. For solar metallicity, whereas the helium cores which burn while naked essentially never go into high-mass black holes, those that burn while clothed do so, beginning at ZAMS mass ~ 20 M_⊙, the precise mass depending on the ~(12)C(α,γ)~(16)O rate as we outline. In this way the SXTs can be evolved, provided that the H envelope of the massive star is removed only following the He core burning. Whereas this scenario was already outlined in 1998 by Brown et al. [NewA 4 (1999) 313], their work was based on evolutionary calculations of Woosley et al. [ApJ 448 (1995) 315] which employed wind loss rates which were too high. In this article we collected results of lower, more correct wind loss rates, finding that these change the results only little. We go into the details of carbon burning in order to reconstruct why the low Fe core masses from naked He stars are relatively insensitive to wind loss rate. The main reason is that without the helium produced by burning the hydrogen envelope, which is convected to the carbon in a clothed star, a central ~(12)C abundance of ~ 1/3 remains unburned in a naked star following He core burning. The later convective burning through ~(12)C + ~(12)C reactions occurs at a temperature T ~ 80 keV. Finally, we show that in order to evolve a black hole of mass ≥ 10 M_⊙ such as observed in Cyg X-1, even employing extremely massive progenitors of ZAMS mass ≥ 60 M_⊙ for the black hole, the core must be covered by hydrogen during a substantial fraction of the core burning. In other works, the progenitor must be a WNL star. We evolve Cyg X-1 in an analogous way to which the SXTs are evolved, the difference being that the companion in Cyg X-1 is more massive than those in the SXTs, so that Cyg X-1 shines continuously.
机译:过去几年中,更多的黑洞软X射线瞬变(SXT)出现了差异,现在已经确定了其中的十二种,这已经挑战了黑洞演化中公认的智慧。高质量X射线双星文学的重建工作要求高达40 M_ stars的恒星演化为低质量的致密物体,这使该质量成为人口合成中常用于形成黑洞的极限。另一方面,要推断出的SXT数量庞大,则即使不是大多数,也要有许多20-35M_⊙的ZAMS恒星最终变成黑洞(Portegies Zwart等,1997; Ergma和van den Heuvel,1998)。 。在本文中,我们证明了这一点,可以通过挑战以下公认的观点来理解,即大质量恒星中氦核的燃烧结果与核被氢封壳覆盖还是在燃烧时“裸露”无关。后一种情况发生在双星中,这是因为在主序或红色巨星阶段,更大质量恒星的包络被罗氏·洛伯溢流转移到同伴时。就太阳金属性而言,裸露时燃烧的氦核基本上不会进入高质量黑洞,而穿衣服时燃烧的氦核则从ZAMS质量〜20M_⊙开始,确切的质量取决于〜(12)C我们概述了(α,γ)〜(16)O的比率。这样,只要大质量恒星的H包层仅在He核燃烧之后才被除去,就可以演化SXT。布朗等人在1998年已经概述了这种情况。 [NewA 4(1999)313],他们的工作基于Woosley等人的进化计算。 [ApJ 448(1995)315]使用了太高的风损率。在本文中,我们收集了更低,更正确的风损率的结果,发现这些结果对结果的影响很小。我们将深入研究碳燃烧的细节,以重建为什么裸露的He恒星中低铁心质量对风速损失相对不敏感的原因。主要原因是,由于没有燃烧氢包膜而产生的氦气,而氢包膜与对流的恒星中的碳对流,在He核燃烧后,裸星中约1/3的中心〜(12)C丰度仍未燃烧。后来通过〜(12)C +〜(12)C反应的对流燃烧发生在温度T〜80 keV处。最后,我们表明,为了产生质量≥10M_⊙的黑洞(例如在Cyg X-1中观察到的),即使使用质量非常大的ZAMS质量≥60M_⊙的祖先作为黑洞,也必须用在核心燃烧的大部分过程中产生氢。在其他作品中,祖先必须是WNL星。我们以类似于SXT进化的方式来进化Cyg X-1,不同之处在于Cyg X-1中的同伴比SXT中的同伴更大,因此Cyg X-1不断发光。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号