首页> 外文期刊>Animal >An observational study investigating the association of ultrasonographically assessed machine milking-induced changes in teat condition and teat-end shape in dairy cows
【24h】

An observational study investigating the association of ultrasonographically assessed machine milking-induced changes in teat condition and teat-end shape in dairy cows

机译:调查超导评估机挤奶诱导的乳酸奶牛乳酸条件和乳酸末端形状变化的关联的观察研究

获取原文
获取原文并翻译 | 示例
           

摘要

Mechanical forces during machine milking induce changes in teat condition which can be differentiated into short-term and long-term changes. Machine milking-induced short-term changes in teat condition (STC) are defined as tissue responses to a single milking and have been associated with the risk of new intramammary infection. Albeit, their association with teat characteristics, such as teat-end shape, has not been investigated by rigorous methods. The primary objective was to determine the association of STC, as measured by ultrasonography, with teat-end shape. The second objective was to describe possible differences in the recovery time of teat tissue after machine milking among teats with different teat-end shapes. Holstein cows (n=128) were enrolled in an observational study, housed in free-stall pens with sand bedding and milked three times a day. Ultrasonography of the left front and right hind teat was performed after teat preparation before milking (t-1), immediately after milking (t(0)) and 1, 3, 5 and 7 h after milking (t(1), t(3), t(5), t(7)). The teat tissue parameters measured from ultrasound scans were teat canal length, teat-end diameter, teat-end diameter at the midpoint between the distal and proximal end of the teat canal, teat wall thickness, and teat cistern width. Teat-end shape was assessed visually and classified into three categories: pointed, flat and round. Multivariable linear regression analyses showed differences in the relative change of teat tissue parameters (compared with t-1) at t(0) among teats with different teat-end shapes, with most parameters showing the largest change for round teats. The premilking values were reached (recovery time) after 7 h in teats with a pointed teat-end shape, whereas recovery time was greater than 7 h in teats with flat and round teat-end shapes. Under the same liner and milking machine conditions, teats with a round teat-end shape had the most severe short-term changes. The results of this observational study indicated that teat-end shape may be one of the factors that contribute to the severity of STC.
机译:机器挤奶过程中的机械力诱导乳汁状况的变化,这可以分为短期和长期变化。机器挤奶诱导的乳酸条件(STC)的短期变化被定义为对单一挤奶的组织反应,并与新的内际感染的风险有关。尽管如此,它们与乳头特性的关系,例如乳头端形状,尚未通过严格的方法来研究。主要目的是确定STC的关联,通过超声检查测量,具有乳头末端形状。第二个目的是在用不同乳头端形状的乳头挤奶后描述乳汁组织恢复时间的可能差异。荷斯坦奶牛(N = 128)读入了一个观察研究,坐落在自由摊位的钢笔里,每天挤奶三次。在乳化(T-1)之前进行乳头制剂(T-1)后进行超声检查,在挤奶后立即进行挤奶后(T(0))和1,3,5和7小时(T(1),T( 3),T(5),T(7))。从超声波扫描测量的乳酸组织参数是乳酸管,乳酸管的远端和近端之间的中点的乳酸管长,乳头端直径,乳头壁厚和奶昔宽度。直观地评估乳头末端形状并将其分为三类:指向,平坦和圆形。多变量的线性回归分析显示出在不同乳头端形状的乳头奶嘴中乳酸组织参数(与T-1相比)的相对变化的差异,大多数参数显示圆奶头的最大变化。达到预流量的值(恢复时间)在具有尖端的乳头末端形状的乳头7小时后,而恢复时间在具有平坦和圆形末端形状的乳头中大于7小时。在相同的衬里和挤奶机条件下,具有圆形乳头末端形状的乳头具有最严重的短期变化。该观察性研究的结果表明,乳头端形状可能是有助于STC严重程度的因素之一。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号