...
首页> 外文期刊>SPE Reservoir Evaluation & Engineering >A Microvisual Study of the Displacement of Viscous Oil by Polymer Solutions
【24h】

A Microvisual Study of the Displacement of Viscous Oil by Polymer Solutions

机译:聚合物溶液置换粘性油的微观研究

获取原文
获取原文并翻译 | 示例
   

获取外文期刊封面封底 >>

       

摘要

Of the various enhanced-oil-recovery (EOR) polymer formulations, newly developed associative polymers show special promise. We investigate pore and pore-network scales because polymer solutions ultimately flow through the pore space of rock to displace oil. We conduct and monitor optically water/oil and polymer-solution/oil displacements in a 2D etched-silicon micromodel. The micromodel has the geometrical and topological characteristics of sandstone. Conventional hydrolyzed-polyacrylamide solutions and newly developed associative-polymer solutions with concentrations ranging from 500 to 2,500 ppm were tested. The crude oil had a viscosity of 450 cp at test conditions. Our results provide new insight regarding the ability of polymer to stabilize multiphase flow. At zero and low polymer concentrations, relatively long and wide fingers of injectant developed, leading to early water breakthrough and low recoveries. At increased polymer concentration, a much greater number of relatively fine fingers formed. The width-to-length ratio of these fingers was quite small, and the absolute length of fingers decreased. At a larger scale of observation, the displacement front appears to be stabilized; hence, recovery efficiency improved remarkably. Above a concentration of 1,500 ppm, plugging of the micromodel by polymer and lower oil recovery was observed for both polymer types. For tertiary polymer injection that begins at breakthrough of water, the severe fingers resulting from water injection are modified significantly. Fingers become wider and grow in the direction normal to flow as polymer solution replaces water. Apparently, improved sweep efficiency of viscous oils is possible (at this scale of investigation) even after waterflood-ing. The associative- and conventional-polymer solutions improved oil recovery by approximately the same amount. The associative polymers, however, showed more-stable displacement fronts in comparison to conventional-polymer solutions.
机译:在各种提高采油率(EOR)的聚合物配方中,新开发的缔合聚合物显示出特殊的前景。我们研究孔隙和孔隙网络尺度,因为聚合物溶液最终会流过岩石的孔隙空间以驱替石油。我们以二维蚀刻硅微模型进行光学和水/油及聚合物溶液/油的位移监测。该微模型具有砂岩的几何和拓扑特征。测试了常规水解聚丙烯酰胺溶液和新开发的浓度为500至2500 ppm的缔合聚合物溶液。在测试条件下,原油的粘度为450cp。我们的结果提供了有关聚合物稳定多相流能力的新见解。在聚合物浓度为零和低时,形成了相对较长和较宽的注入剂指状部,导致早期的水突破和低回收率。在增加的聚合物浓度下,形成大量的相对较细的指状物。这些手指的宽长比很小,并且手指的绝对长度减小。在更大的观察范围内,位移前沿似乎是稳定的。因此,回收效率显着提高。浓度高于1,500 ppm时,两种聚合物类型均观察到聚合物堵塞了微模型并降低了油回收率。对于从水的渗入开始的三次聚合物注入,由注入水引起的严重的手指被显着地改变。随着聚合物溶液替代水,手指变得更宽,并沿着正常流动的方向生长。显然,即使注水后,仍可以提高粘性油的扫油效率(在此调查规模下)。缔合聚合物溶液和常规聚合物溶液的采油率几乎相同。然而,与常规聚合物溶液相比,缔合聚合物显示出更稳定的位移前沿。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号