首页> 外文期刊>Mechanics of materials >Micromechanical study of fabric evolution in quasi-static deformation of granular materials
【24h】

Micromechanical study of fabric evolution in quasi-static deformation of granular materials

机译:颗粒材料准静态变形过程中织物演化的微力学研究

获取原文
获取原文并翻译 | 示例
       

摘要

In micromechanical studies of granular materials, relations are investigated between macro-level, continuum characteristics and micro-level, (inter) particle characteristics. For quasi-static deformation of granular materials, the fabric tensor is an important micromechanical characteristic that describes the orientational distribution of contacts between particles. The evolution of the fabric tensor during quasi-static deformation has been investigated, using two-dimensional Discrete Element Method simulations of constant-pressure tests of a dense and a loose isotropic initial assembly. Invariants of the fabric tensor are the coordination number, i.e. the average number of contacts per particle, and the fabric anisotropy, i.e. the difference between the principal values of the fabric tensor. At large strains, both coordination number and fabric anisotropy become constant. This constant value is the same for the dense and the loose initial assembly, i.e. a critical fabric state is attained. The evolution towards the critical state value for coordination number is much faster than for fabric anisotropy. The three micromechanical mechanisms through which the fabric tensor can change are contact creation, contact disruption and contact reorientation. Contact disruption is the dominant mechanism (except at the steady state) that is strongly anisotropic. The rate of contact disruption decreases rapidly with increasing imposed strain. Contact creation is approximately an isotropic mechanism. The rate of contact creation is fairly constant over the range of imposed strains. Fabric change due to contact reorientation is small, except at the steady state. An evolution relation is proposed for the changes in the fabric tensor as a function of the fabric tensor and the strain increment tensor. With its coefficients obtained by fitting with the data for the fabric tensor from the Discrete Element Method simulations, good agreement is observed between results from these simulations and from the proposed fabricevolution relation.
机译:在颗粒材料的微机械研究中,研究了宏观水平,连续性特征和微观水平(内部)颗粒特征之间的关系。对于粒状材料的准静态变形,织物张量是重要的微机械特性,它描述了粒子之间接触的定向分布。使用二维离散元方法模拟密集和松散各向同性初始组件的恒压测试,研究了准静态变形过程中织物张量的演变。织物张量的不变性是配位数,即每个粒子的平均接触数,以及织物各向异性,即织物张量的主值之间的差。在大应变下,配位数和织物各向异性都变得恒定。该常数对于密实和松散的初始组件是相同的,即,达到临界织物状态。配位数向临界状态值的演化比织物各向异性要快得多。织物张量可以通过其改变的三个微机械机制是接触的产生,接触的破坏和接触的重新定向。接触破坏是强各向异性的主要机理(稳态时除外)。接触破坏的速率随着施加的应变的增加而迅速降低。接触的建立大致是各向同性的。在施加的应变范围内,接触产生的速率相当恒定。除了在稳态下,由于接触重新定向造成的织物变化很小。提出了一种关于织物张量随织物张量和应变增量张量变化的演化关系。通过将其系数与离散元素方法模拟中的织物张量的数据进行拟合,可以得出这些模拟结果与拟议的织物演化关系之间的一致性。

著录项

  • 来源
    《Mechanics of materials》 |2012年第1期|p.120-129|共10页
  • 作者

    N.P. Kruyt;

  • 作者单位

    Department of Mechanical Engineering, University of Twente, P.O. Box 217, 7500 AE Enschede, The Netherlands;

  • 收录信息 美国《科学引文索引》(SCI);美国《工程索引》(EI);
  • 原文格式 PDF
  • 正文语种 eng
  • 中图分类
  • 关键词

    granular media; micromechanics; deformation; fabric tensor;

    机译:颗粒状介质微力学形变;织物张量;

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号