...
首页> 外文期刊>Mathematical Problems in Engineering >Dimensionless Analytical Solution and New Design Formula for Lateral-Torsional Buckling of I-Beams under Linear Distributed Moment via Linear Stability Theory
【24h】

Dimensionless Analytical Solution and New Design Formula for Lateral-Torsional Buckling of I-Beams under Linear Distributed Moment via Linear Stability Theory

机译:基于线性稳定性理论的线性分布弯矩下工字梁横向扭转屈曲的无量纲解析解和新设计公式

获取原文
获取原文并翻译 | 示例
           

摘要

Even for the doubly symmetric I-beams under linear distributed moment, the design formulas given by codes of different countries are quite different. This paper will derive a dimensionless analytical solution via linear stability theory and propose a new design formula of the critical moment of the lateral-torsional buckling (LTB) of the simply supported I-beams under linear distributed moment. Firstly, the assumptions of linear stability theory are reviewed, the dispute concerning the LTB energy equation is introduced, and then the thinking of Plate-Beam Theory, which can be used to fully resolve the challenge presented by Ojalvo, is presented briefly; secondly, by introducing the new dimensionless coefficient of lateral deflection, the new dimensionless critical moment and Wagner's coefficient are derived naturally from the total potential energy. With these independent parameters, the new dimensionless analytical buckling equation is obtained; thirdly, the convergence performance of the dimensionless analytical solution is discussed by numerical solutions and its correctness is verified by the numerical results given by ANSYS; finally, a new trilinear mathematical model is proposed as the benchmark of formulating the design formula and, with the help of 1st Opt software, the four coefficients used in the proposed dimensionless design formula are determined.
机译:即使对于线性分布弯矩下的双对称工字梁,不同国家/地区代码给出的设计公式也大不相同。本文将通过线性稳定性理论推导无量纲的解析解,并为线性分布弯矩下的简支工字梁的横向扭转屈曲(LTB)临界弯矩的临界弯矩设计新公式。首先回顾了线性稳定性理论的假设,介绍了有关LTB能量方程的争论,然后简要介绍了可以完全解决Ojalvo提出的挑战的板束理论的思想;其次,通过引入新的无量纲的横向挠度系数,新的无量纲的临界矩和瓦格纳系数自然地从总势能中导出。利用这些独立的参数,获得了新的无量纲分析屈曲方程。第三,通过数值解讨论了无量纲解析解的收敛性能,并通过ANSYS给出的数值结果验证了其正确性。最后,提出了一个新的三线性数学模型作为制定设计公式的基准,并借助1st Opt软件确定了所提出的无量纲设计公式中使用的四个系数。

著录项

  • 来源
    《Mathematical Problems in Engineering》 |2017年第12期|4838613.1-4838613.23|共23页
  • 作者单位

    Nanjing Inst Technol, Sch Architecture & Engn, Nanjing 211167, Jiangsu, Peoples R China;

    Northeast Petr Univ, Daqing 163318, Heilongjiang, Peoples R China;

    Northeast Petr Univ, Daqing 163318, Heilongjiang, Peoples R China;

    Northeast Petr Univ, Daqing 163318, Heilongjiang, Peoples R China;

  • 收录信息
  • 原文格式 PDF
  • 正文语种 eng
  • 中图分类
  • 关键词

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号