首页> 外文会议>International Conference on Nuclear Engineering >ANALYSIS OF TRANSIENT COOLANT VOID FORMATION DURING A GUILLOTINE-TYPE HX TUBE RUPTURE EVENT IN THE STAR-LM SYSTEM EMPLOYING A SUPERCRITICAL CO_2 BRAYTON CYCLE
【24h】

ANALYSIS OF TRANSIENT COOLANT VOID FORMATION DURING A GUILLOTINE-TYPE HX TUBE RUPTURE EVENT IN THE STAR-LM SYSTEM EMPLOYING A SUPERCRITICAL CO_2 BRAYTON CYCLE

机译:超临界CO_2 Brayton循环中的星LM系统中断臂型HX管破裂事件瞬态冷却剂空隙形成分析

获取原文

摘要

One proposed concept for the STAR-LM Lead Fast Reactor (LFR) incorporates a supercritical CO_2 gas turbine Brayton cycle to achieve high cycle efficiency and reduced plant footprint. In this design, 100+% of core full power is transferred by natural circulation from the core, located at the bottom of the reactor vessel, to in-vessel heat exchangers (HXs) located at the top of the vessel in the annulus between the core shroud and vessel inner wall. Although this approach extremely simplifies the plant design, the presence of the HX's within the vessel raises concerns regarding the potential rupture of a HX tube that would initiate a high-pressure blowdown of CO_2 into the lead coolant. The principal issue is to what extent, if any, is void entrained downwards with the coolant and then upwards through the core where adverse reactivity effects or degraded heat removal could result. To address this question, a scoping analysis of transient void formation during a guillotine-type HX tube rupture event in the STAR-LM employing a supercritical CO_2 Brayton cycle has been performed. The void formation process is evaluated by solving a coupled set of ordinary differential equations describing: ⅰ) the supercritical CO_2 blowdown, ⅱ) bubble center-of-mass trajectory, ⅲ) bubble growth rate, ⅳ) bubble gas internal energy, and ⅴ) discrete bubble formation rate due to Taylor instability at the bubble/coolant interface. The results indicate that for thermal hydraulic conditions consistent with the current STAR-LM design, the peak blowdown rate from a single tube rupture is ~ 2.5 kg/sec. The void formation process is dominated by large coherent gas bubbles that penetrate minimally downwards into the coolant due to the large coolant density. Rather, the gas pockets are predicted to periodically rise due to buoyancy and vent to the core cover gas region, as opposed to being swept downwards with the coolant. Moreover, the total CO_2 fraction that is rendered in the form of discrete bubbles during blowdown is found to be small (~ 3 %), and the bubbles are of fairly large diameter (≥ 0.7 cm). Thus, these discrete bubbles are also calculated to benignly rise to the cover gas region since the terminal rise velocity for the bubbles exceeds the average lead coolant down flow velocity below the HX.
机译:一个提出的概念的STAR-LM铅快堆(LFR)包括超临界CO_2燃气轮机Brayton循环,以实现高循环效率和降低植物足迹。在这种设计中,100 +%的核心全功率通过从位于反应器容器底部的核心的天然循环传递到位于血管顶部的容器热交换器(HXS)中核心护罩和容器内壁。虽然这种方法极为简化了工厂设计,HX存在的内血管引起了关于HX管会引发CO_2的高压放空到铅冷却剂的潜在破裂的担忧。主要问题是如果有的话,如果有的话,如果有的话,通过冷却剂向上夹带,然后通过核心向上通过不利的反应性效应或降低的热量去除。为了解决这个问题,在STAR-LM采用超临界CO_2布雷顿循环一个闸刀式HX管破裂事件期间的瞬态空隙形成的作用域分析已被执行。 ⅰ)超临界CO_2泄料,ⅱ)气泡中心的质量轨迹,ⅲ)气泡的增长速度,ⅳ)气泡气体的内部能量,并且ⅴ):空隙的形成过程是通过求解一耦合组常微分方程描述的评价离散泡沫形成速率由于在气泡/冷却剂界面泰勒不稳定。结果表明,与当前STAR-LM设计一致热工水力条件,从一个单一的管破裂峰值排污率是约2.5千克/秒。空隙形成过程由大的相干气泡主导,该气泡由于大的冷却剂密度而渗透到冷却剂中。相反,预测气体袋由于浮力和通风口到芯覆盖气体区域而定期上升,而不是用冷却剂向下扫描。而且,在排放期间离散气泡的形式呈现的总分数CO_2被发现是小(约3%),气泡是相当大直径(≥0.7厘米)的。因此,这些离散气泡还计算成良性地升到覆盖气体区域,因为气泡的终端上升速度超过了HX下方的平均铅冷却剂下流速度。

著录项

相似文献

  • 外文文献
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号