首页> 外文会议>Conference on sensory phenomena and measurement instrumentation for smart structures and materials >Investigation of Transverse Stress Measurements by Using Embedded Fiber Bragg Grating Sensors subjected to Host Poisson's Effect
【24h】

Investigation of Transverse Stress Measurements by Using Embedded Fiber Bragg Grating Sensors subjected to Host Poisson's Effect

机译:使用嵌入式光纤布拉格光栅传感器进行横向应力测量的调查

获取原文
获取外文期刊封面目录资料

摘要

In many situations, it is desirable to measure the load acting in a specific direction by measuring the strain induced by Poisson effects in a direction perpendicular to the load direction. For this to be possible, a fixed relationship between the strains in both directions must be known. This can be useful, for example, when the geometry is such that there is not sufficient room to locate a strain gauge parallel to the load direction but a gauge can be placed in a transverse plane. In this paper, we investigate the use of a fiber Bragg grating in such an arrangement with the fiber embedded within the host material. The investigation is done by theoretical, numerical and experimental approaches and we concentrate on two aspects: (a) the non-uniform strain transfer, particular in axial strains, due to shear-lag effects, and (a) the effect of induced birefringence in the optical fiber due to a load cross to its axis. The results of these approaches indicate that the strains of an embedded fiber sensor subjected to transverse loads are dependent on the location of the embedded sensor and the material properties of the host material. The results also show that when the Young's modulus of the host material is much less than the modulus of the embedded sensor, the Bragg spectrum broadening due to induced birefringence is not significant. However, a lower host Young's moduus also results in longer sections on non-uniform axial strain near the ingress and egress sections of the optical fiber. These two factors must be balanced if we desire to use conventional methods of Bragg grating interrogation that measure only the central wavelength of the Bragg grating's spectrum. In the case investigated (Host Young's modulus of 4.83 GPa) full strain build-up requires approx4mm of fiber length at each end. Likewise, the transverse stress coupling into the fiber modifies its wavelength-shift-to-axial-strain-coefficient by about 6percent.
机译:在许多情况下,希望通过测量垂直于负载方向的方向上的泊松效果引起的菌株来测量作用在特定方向上的负荷。为了这一点,必须知道两个方向的应变之间的固定关系。例如,当几何形状使得没有足够的空间来定位与负载方向的应变仪来定位时,这可以是有用的,但是可以将规格放置在横向平面中。在本文中,我们研究了在这种布置中使用纤维在主体材料内的布置中的使用。调查是通过理论,数值和实验方法进行的,我们专注于两个方面:(a)由于剪切效应,特别是轴向菌株的非均匀应变转移,以及(a)诱导的双折射的效果光纤引起的负载交叉到其轴线。这些方法的结果表明,经过横向载荷的嵌入式光纤传感器的菌株取决于嵌入式传感器的位置和主体材料的材料特性。结果还表明,当主体材料的杨氏模量远小于嵌入式传感器的模量时,由于诱导的双折射而导致的布拉格光谱宽度不显着。然而,较低的宿主杨氏模型也导致较长的轴向应变靠近光纤的入口和出口部分附近的较长部分。如果我们希望使用仅测量布拉格光栅光栅的中心波长的布拉格光栅询问的传统方法,必须平衡这两个因素。在调查的情况下(宿主杨氏模量为4.83GPa),全菌株堆积需要大约4mm的纤维长度在每一端。同样地,横向应力耦合到纤维中通过大约6平方改变其波长移位到轴向应变系数。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号