【24h】

DESIGN AND DEVELOPMENT OF A NOVEL SOFT-AND-RIGID HYBRID ACTUATOR SYSTEM FOR ROBOTIC APPLICATIONS

机译:机器人应用新型刚柔混合动力系统的设计与开发

获取原文

摘要

This paper presents the design and development of a pneumatic soft-and-rigid hybrid actuator system that consists of half-bellow shaped soft sections in-between block shape rigid sections. The hybrid actuator architecture allows for selective actuation of each soft section (acting as a joint) with precise control over its bending motion. The soft half-bellow section is designed as a series of hollow ridges extending straight to a flat base. This geometry provides forward and backward bending motion when subjected to positive and negative pressure, respectively. Bending occurs as the ridges of the soft section expanc. And contract more than the flat base due to pressure variations. The rigid sections serve as connections between soft actuator sections and enhance force transfer. As a case study, a hybrid actuator system was designed as a soft robotic digit with three soft joints and four rigid connecting sections. Finite element analysis was performed to evaluate the design parameters such as number of ridges and materials for the robotic finger. The joints (from proximal to distal) were designed to have four, three, and two ridges, respectively, to generate the desired range of angular motion. Fabrication of the finger was done with silicone rubber RTV-4234-T4 and PMC polyurethane rubber using a combination of compression molding and overmolding processes. The angular and translational displacements of the robotic finger were experimentally and numerically evaluated at different pressures. The trajectory of the fingertip is comparable to those reported in literature for continuous soft actuators with a similar length. The significance of this actuator system is that both range of angular and translational motions are achieved at low pressure, less than 70kPa, as opposed to reported pressures of greater than lOOkPa. The presented results show the great potential of the soft robotic finger for use in robotic, rehabilitation, and assistive device applications.
机译:本文介绍了一种气动刚柔混合执行器系统的设计和开发,该系统由位于块状刚性部分之间的半波纹状柔性部分组成。混合执行器架构允许对每个软部分(充当关节)进行选择性控制,并对其弯曲运动进行精确控制。柔软的半波纹管部分设计为一系列空心脊,这些空心脊直接延伸到平坦的基座。当分别承受正压和负压时,此几何形状可提供向前和向后的弯曲运动。弯曲发生在软截面的隆起处。由于压力变化,收缩量比平底还要大。刚性部分用作软促动器部分之间的连接,并增强了力的传递。作为案例研究,混合执行器系统被设计为具有三个软关节和四个刚性连接部分的软机器人手指。进行了有限元分析以评估设计参数,例如机器人手指的脊数和材料。关节(从近端到远端)设计为分别具有四个,三个和两个脊,以生成所需的角度运动范围。用硅橡胶​​RTV-4234-T4和PMC聚氨酯橡胶通过压缩成型和包覆成型工艺的组合来制作手指。在不同压力下,通过实验和数值方法评估了机械手指的角位移和平移位移。指尖的轨迹可与文献中报道的具有相似长度的连续式软执行器相媲美。该致动器系统的重要性在于,在小于70kPa的低压下实现了角运动和平移运动的范围,这与所报道的大于100kPa的压力相反。呈现的结果表明,柔软的机械手指在机器人,康复和辅助设备应用中具有巨大的潜力。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号