首页> 外文会议>2014 International Conference on Green Computing Communication and Electrical Engineering >A novel high gain DC-DC multilevel boost converter using voltage-lift switched-inductor cell
【24h】

A novel high gain DC-DC multilevel boost converter using voltage-lift switched-inductor cell

机译:一种采用升压开关电感单元的新型高增益DC-DC多电平升压转换器

获取原文
获取原文并翻译 | 示例

摘要

This paper presents a novel high gain DC-DC multilevel boost converter using voltage-lift switched-inductor (VLSI) cell. Cascading of conventional boost converters is not a viable solution to achieve high voltage gain. Thus, DC-DC multilevel converters are employed to achieve high conversion ratio. The proposed high gain DC-DC multilevel boost converter topology is non-isolated which combines the function of voltage-lift switched-inductors (VLSI) cell and voltage multiplier cell. In this paper voltage-lift switched-inductor (VLSI) cell is used to improve the boost capability of multilevel DC-DC converter. 2N capacitors, 2N+3 diodes, two inductors and single switch are needed to design proposed N-level DC-DC topology. Proposed DC-DC multilevel converter topology can be synthesized by using low voltage rating devices because blocking voltage across each power devices is less. The main advantage of this multilevel topology is high conversion ratio is achieved without using coupled inductor, transformer and extreme duty cycle. The conversion ratio of this multilevel DC-DC converter is depends upon the duty cycle and number of levels present in the voltage multiplier cell. The proposed DC-DC multilevel converter has been designed for three levels with rated power 200W, input supply voltage is 12V, output voltage is 288V and switching frequency is 50kHz. The proposed DC-DC multilevel converter topology is simulated in MATLAB/SIMULINK. The simulation results will verify the validity of the analytical design.
机译:本文提出了一种采用升压开关电感(VLSI)单元的新型高增益DC-DC多电平升压转换器。传统升压转换器的级联不是实现高电压增益的可行解决方案。因此,采用DC-DC多电平转换器来实现高转换率。所提出的高增益DC-DC多电平升压转换器拓扑是非隔离的,该拓扑结合了升压开关电感(VLSI)单元和电压倍增单元的功能。本文采用升压开关电感(VLSI)单元来提高多电平DC-DC转换器的升压能力。设计建议的N级DC-DC拓扑需要2N个电容器,2N + 3个二极管,两个电感器和一个开关。提议的DC-DC多电平转换器拓扑可以通过使用额定电压较低的设备进行合成,因为每个电源设备之间的阻塞电压都较小。这种多级拓扑的主要优点是无需使用耦合的电感器,变压器和极端占空比即可实现高转换率。该多电平DC-DC转换器的转换比取决于占空比和电压倍增单元中存在的电平数量。提出的DC-DC多电平转换器已针对额定功率为200W的三个电平进行设计,输入电源电压为12V,输出电压为288V,开关频率为50kHz。在MATLAB / SIMULINK中对提出的DC-DC多电平转换器拓扑进行了仿真。仿真结果将验证分析设计的有效性。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号