首页> 外国专利> Household Multi-Products through-Cutting Box, Integrated with suspension openings, with claw back-section replacement, simultaneously as a high-edge surface in joint combination, with pressure-relieving knife-strength areas and arc-cutting profile

Household Multi-Products through-Cutting Box, Integrated with suspension openings, with claw back-section replacement, simultaneously as a high-edge surface in joint combination, with pressure-relieving knife-strength areas and arc-cutting profile

机译:家用多产品直通切割盒,集成有悬架开口,可更换爪后部,同时作为高边表面联合使用,具有卸压刀强度区域和弧形轮廓

摘要

Household products-through-cutting box (1)-, with non-injurious holding contours, suspension openings, claw back-cutting replacement, joint combination, knife arch profile,.. with flat partitions for several different average products box-shaped and in the rear area the knife-mounted guide-ladder with which several products are simultaneously separated, at the back is a covered saw-room with knife-storage-fixed-clamp (2). with side or middle-length axle shaft support,... with opening stop or box total opening stop in one unit,... with low approx.1 mm high lines at box contour slopes,just without these 4-box-shaped corners..... with at least approximately 1cm opening also integrated in the lower part of the knife handle opening page,Yeah. with this opening, the box is hung, stored, and thus the stored knife is specially secured with... with opening shape between left and right knife guide lips,...with in upper rear lid area between joint areas up to 4-finger-wide indentations, finger-hand, contours,..... with a thumb-grip mounted in the front middle approx.8 cm long x 2 cm wide in the edge of the box,... can also be adjusted or disabled by means of an average process,......with top and bottom opening to hang to the box,... with a small pencil in the intermediate-area edge, and an opening as a U-claw protection on the other opposite-shaft edge,Yeah. with matching new knife-pressure-relief slightly curved total through-cutting blade-length profile = characterized by the fact that the box shaft axis at the side of the shaft-shaft-holder or there in the middle with wide joint (3) simultaneously as an opening stop,Box total opening stop has, at the same time as a high-edge surface is made of a unit (4), and below with approximately 1 mm high lines, box contour bridge is made just without the 4-box shape corners (4).
机译:家用产品直切式包装盒(1)-,具有无伤害的固定轮廓,悬吊开口,爪形反切替换,接头组合,刀弓轮廓,..带有用于多个不同形状的普通产品的平面隔板后面是装有刀片的导向梯,可同时分离出几种产品,后面是带顶棚的锯室,锯室带有固定刀夹(2)。带侧面或中等长度的轴支撑,...带一个限位器或一个箱的总限位器,...在箱形轮廓斜线上只有低大约1 mm高的线,而没有这四个箱形拐角.....在刀柄开口页的下部也集成了至少约1cm的开口,是的。有了这个开口,就可以将盒子挂起来,存放起来,这样就可以用……专门固定存放的刀子了……在左,右刀口之间有开口形状,……在关节区域之间的上后盖区域中最多可达4个。手指宽的压痕,手指,手掌的轮廓.....在前中部装有拇指握把,盒子的边缘大约长8 cm x宽2 cm,也可以调节或通过一般的过程来禁用.........顶部和底部的开口挂在盒子上,...在中间区域的边缘上用一支小铅笔,在开口处有​​一个U形爪保护的开口其他相对轴的边缘,是的。带有匹配的新的刀压释放装置,略微弯曲的总直切刀片长度轮廓=特征在于,箱形轴的轴同时位于轴-轴支架的一侧或中间,并带有宽缝(3)作为高空挡块,箱体总高挡块具有一个高边表面,同时由一个单元(4)构成,而在下面有大约1毫米高的线的情况下,箱形轮廓桥只是不带4个箱形形角(4)。

著录项

  • 公开/公告号DE202019004966U1

    专利类型

  • 公开/公告日2020-03-26

    原文格式PDF

  • 申请/专利权人 HELMUT LUTZENBERGER;

    申请/专利号DE202019004966U1

  • 发明设计人

    申请日2019-11-26

  • 分类号B26D3/30;B26B3;

  • 国家 DE

  • 入库时间 2022-08-21 11:01:01

相似文献

  • 专利
获取专利

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号