首页> 外文期刊>Journal of aerosol medicine: the official journal of the International Society for Aerosols in Medicine >Characterization of the Spray Velocities from a Pressurized Metered-Dose Inhaler
【24h】

Characterization of the Spray Velocities from a Pressurized Metered-Dose Inhaler

机译:加压定量吸入器的喷雾速度表征

获取原文
获取原文并翻译 | 示例
           

摘要

Background: Pressurized metered dose inhalers (pMDIs) are widely used to deliver aerosolized medications to the lungs, most often to relieve the symptoms of asthma. Over the past decade, pMDIs have been modified in several ways to eliminate the use of chlorofluorocarbons in their manufacture while increasing efficacy. Numerical simulations are being used more frequently to predict the flow and deposition of particles at various locations, both inside the respiratory tract as well as in pMDIs and add-on devices. These simulations require detailed information about the spray generated by a pMDI to ensure the validity of their results. Methods: This paper presents detailed, spatially resolved velocity measurements of the spray emitted from salbutamol sulfate pMDIs obtained using optically triggered particle image velocimetry (PIV). Instantaneous planar velocity measurements were taken and ensemble-averaged at nine different times during the spray event ranging from 1.3 to 100 msec after a pneumaticallycontrolled actuation.Results and Conclusions: The mean spray velocities were shown to be bimodal in time, with two velocity peaks and velocity magnitudes found to be much lower than published data from instantaneous single point measurements. Planar velocity data at each time step were analyzed to produce prescriptive velocity profiles suitable for use in numerical simulations. Spray geometry data are also reported. Statistical comparisons from several thousand individual spray events indicate that there is no significant difference in measured velocity among (1) two brands of pMDI canisters, (2) two pMDIs of the same brand but having different lot numbers, and (3) a full pMDI versus an almost empty pMDI. The addition of a secondary air flow of 30 SLPM (to represent simultaneous inhalation and spray actuation) deflected the spray downward but did not have a significant effect on flow velocity. Further experiments with an added cylindrical spacer revealed that within the spacer, the spray direction and cone angle were altered, although the peak velocities remained similar.
机译:背景:加压计量吸入器(pMDIs)被广泛用于向肺部输送雾化药物,通常用于缓解哮喘症状。在过去的十年中,pMDI已通过多种方式进行了修饰,以消除氯氟烃在其制造过程中的使用,同时提高了功效。越来越多地使用数值模拟来预测颗粒在呼吸道内以及pMDI和附加设备中各个位置的流动和沉积。这些模拟需要有关pMDI产生的喷雾的详细信息,以确保其结果的有效性。方法:本文介绍了使用光学触发粒子图像测速仪(PIV)获得的硫酸沙丁胺醇pMDI发出的喷雾的详细空间分辨速度测量结果。在气动控制致动后的1.3至100毫秒的喷雾过程中,进行了瞬时平面速度测量,并在9个不同的时间进行了集合平均。发现速度幅度远低于瞬时单点测量的公开数据。分析每个时间步的平面速度数据,以生成适用于数值模拟的规定速度曲线。还报告了喷雾几何数据。来自数千次喷洒事件的统计比较表明,(1)两个品牌的pMDI滤罐,(2)同一品牌但具有不同批号的两个pMDI,以及(3)完整的pMDI在测量速度上没有显着差异。与几乎为空的pMDI相比。附加的30 SLPM二次气流(代表同时吸入和喷雾启动)使喷雾向下偏转,但对流速没有明显影响。使用附加的圆柱形垫片的进一步实验表明,尽管峰值速度保持相似,但在垫片内,喷雾方向和锥角均发生了变化。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号