...
首页> 外文期刊>The Science of the Total Environment >Impact of catalyst load, chemical oxygen demand and nitrite on disinfection and removal of contaminants during catalytic ozonation of wastewater
【24h】

Impact of catalyst load, chemical oxygen demand and nitrite on disinfection and removal of contaminants during catalytic ozonation of wastewater

机译:废水催化臭氧化过程中催化剂负载,化学需氧量和亚硝酸盐对消毒和污染物去除的影响

获取原文
获取原文并翻译 | 示例
           

摘要

Calcium-silicate mineral Polonite (R) and aluminum-based catalyst (AL-1010S), previously identified as promising materials for catalytic ozonation, were used as catalysts to investigate the impact of some operating conditions (ratio ozone feed concentration to catalyst load) and wastewater characteristics (chemical oxygen demand - COD and nitrite - NO2 concentration) on the disinfection and removal of contaminants of emerging concern (CECs) during catalytic ozonation of wastewater. Tests conducted in synthetic wastewater using two different ozone gas concentration (4 and 8 g (nm(3))) and 6 different catalyst loads provided ratios of 0.08, 0.11, 0.16, and 0.32. Results from the experiments indicated that the ratio of 0.11 was optimal and reached residual disinfection below 2 MPN mL(-1) from the initial concentration of 5 +/- 2 x 10 (5) MPN mL(-1) and removal of atrazine (ATZ) above 80% from the initial concentration of 100 +/- 10 mu g L-1 for an ozone dose of 41-45 mg L-1. Catalytic ozonation with the selected materials enhanced disinfection and ATZ removal from synthetic wastewater (SWW) in comparison to non-catalytic ozonation by making the treatment performance less sensitive to increased chemical oxygen demand (COD) and nitrite (NO2) in the matrix. Validation of the results in real wastewater effluents confirmed that catalytic ozonation enhanced disinfection. Catalytic ozonation using Polonite (R) and AL-1010S provided residual bacteria level of 0.6 +/- 0.42 MPN mL(-1) and 0.29 +/- 0.41 MPN mL(-1), while non-catalytic ozonation lead to an average residual bacteria level of 1.26 +/- 0.09 MPN mL(-1) for the same range of transferred ozone dose. However, under the conditions tested, a limited number of CECs were extracted at levels above the limits of quantification and further validation work required to evaluate the performance of catalytic ozonation for the removal of CECs. (C) 2018 Elsevier B.V. All rights reserved.
机译:先前被确定为催化臭氧化的有前途的材料的硅酸钙矿物矿物Polonite(R)和铝基催化剂(AL-1010S)被用作催化剂,以研究某些操作条件(臭氧进料浓度与催化剂负载比)的影响,以及废水的特征(化学需氧量-COD和亚硝酸盐-NO2浓度)对废水的催化臭氧化过程中的新出现的污染物(CEC)的消毒和去除。在合成废水中使用两种不同的臭氧气体浓度(4和8 g(nm(3)))和6种不同的催化剂负载进行的测试提供的比率为0.08、0.11、0.16和0.32。实验结果表明,最佳比例为0.11,从5 +/- 2 x 10(5)MPN mL(-1)的初始浓度到2 MPN mL(-1)以下达到残留消毒水平,并去除了r去津(臭氧剂量为41-45 mg L-1时,初始浓度为100 +/- 10μgL-1,高于80%。与非催化臭氧化相比,使用所选材料进行的催化臭氧化可增强对合成废水的消毒和ATZ去除,这使处理性能对基质中化学需氧量(COD)和亚硝酸盐(NO2)的敏感性降低。在实际废水中验证结果的结果证实了催化臭氧化技术可以提高消毒效果。使用Polonite(R)和AL-1010S进行催化臭氧化可提供0.6 +/- 0.42 MPN mL(-1)和0.29 +/- 0.41 MPN mL(-1)的残留细菌水平,而非催化臭氧化可导致平均残留对于相同范围的已转移臭氧剂量,细菌水平为1.26 +/- 0.09 MPN mL(-1)。但是,在所测试的条件下,提取的有限数量的CEC的含量超出了定量限制,并且需要进行进一步的验证工作来评估催化臭氧氧化法去除CEC的性能。 (C)2018 Elsevier B.V.保留所有权利。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号