首页> 外文期刊>International Journal of Heat and Mass Transfer >Influence of entrance geometry on flow field and heat transfer performance in stationary two-pass smooth parallelogram channels
【24h】

Influence of entrance geometry on flow field and heat transfer performance in stationary two-pass smooth parallelogram channels

机译:入口几何形状对固定二通平滑平行四边形通道中流场和传热性能的影响

获取原文
获取原文并翻译 | 示例
       

摘要

PIV and Infrared Thermometry measurements are respectively conducted to study the effects of entrance geometry and Reynolds number (Re) on the detailed flow fields and local temperature distributions in a stationary two-pass smooth parallelogram channel with 180-deg sharp turn. Two entrance geometries, including a fully developed inlet condition (FDI) as well as an asymmetrically and suddenly contracted inlet condition (ASI), are investigated. The smooth parallelogram channel has equal adjacent sides of 45.5 mm in length and two pairs of adjacent angles are 45-deg and 135-deg. Local (Nu_0) and regionally averaged (Nu_0) Nusselt numbers over entire top and bottom walls along the first and second passages and through the bend region with the associated pressure drop are examined under Re ranging from 5000 to 20,000. Moreover, cross-sectional secondary-flow patterns as well as the near-wall streamwise mean velocity components and turbulent kinetic energy are analyzed to correlate the relationship between flow characteristics and heat transfer distributions at Re= 10,000. The most distinct finding of the present study is that the asymmetric thermal and fluid flow features on the top and bottom wall side, in contrast to symmetric ones in the corresponding square and rectangular channels. The affected top and bottom wall Nu_0 distributions of ASI respectively extends downstream to the mid-turn and the middle of second pass. Compared with FDI, ASI elevates the Nu_0 about 65.3-70.1%, 14.2-13.7%, and 23.9-14.0% in the first passage, turn region, and second passage, respectively, under constant flow rate condition. Thermal performance factors of the ASI are about 43.5% and 53.7% higher than the FDI at Re = 5000 and 20,000, respectively. Moreover, the correlations of Nu_0 and fanning friction factor (f_0) with Re are obtained and further compared with those of the corresponding square channels available from the literature.
机译:分别进行PIV和红外测温,以研究入口几何形状和雷诺数(Re)对固定的180度急转弯两通平滑平行四边形通道中详细流场和局部温度分布的影响。研究了两种入口几何形状,包括完全发展的入口条件(FDI)以及不对称且突然收缩的入口条件(ASI)。光滑的平行四边形通道的相邻边的长度相等,为45.5 mm,两对相邻的角度分别为45度和135度。在Re的范围从5000到20,000的条件下,检查沿第一通道和第二通道的整个顶壁和底壁上的局部(Nu_0)和区域平均(Nu_0)的努塞尔特数,并通过弯曲区域以及相关的压降。此外,分析了二次流的横截面模式以及近壁流平均速度分量和湍动能,以关联Re = 10,000时流动特性与传热分布之间的关系。本研究最明显的发现是,与相应的正方形和矩形通道中的对称流动相反,顶壁和底壁侧的流动和流体流动不对称。 ASI的受影响的顶壁和底壁Nu_0分布分别向下游延伸至第二道次中线和中间。与FDI相比,在恒定流量条件下,ASI在第一通道,转弯区域和第二通道中分别将Nu_0升高了65.3-70.1%,14.2-13.7%和23.9-14.0%。在Re = 5000和20,000时,ASI的热性能系数分别比FDI高约43.5%和53.7%。此外,获得了Nu_0和扇形摩擦因数(f_0)与Re的相关性,并将其与可从文献中获得的相应方形通道的相关性进行了比较。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号