...
首页> 外文期刊>Revista Latinoamericana de Metalurgia y Materiales >COMPORTAMIENTO EN DESGASTE DESLIZANTE DE POLIETILENO DE ALTA DENSIDAD ENTRECRUZADO CON RADIACIóN GAMMA ( SLIDING WEAR BEHAVIOUR OF HIGH DENSITY POLYETHYLENE CROSS-LINKED BY GAMMA RADIATION )
【24h】

COMPORTAMIENTO EN DESGASTE DESLIZANTE DE POLIETILENO DE ALTA DENSIDAD ENTRECRUZADO CON RADIACIóN GAMMA ( SLIDING WEAR BEHAVIOUR OF HIGH DENSITY POLYETHYLENE CROSS-LINKED BY GAMMA RADIATION )

机译:伽马辐射交联的高密度聚乙烯的滑动磨损行为(滑动磨损行为)

获取原文
           

摘要

El propósito del trabajo fue evaluar el comportamiento de polietilenos irradiados con rayos gamma sometidos a desgaste deslizante. Para ellos se utilizaron dos polietilenos lineales, que fueron irradiados con radiación gamma a temperatura ambiente, aplicándose a cada grupo dosis de 2, 5, 10 y 20 Mrad. Los estudios tribológicos fueron realizados usando un tribómetro Pin On Disc. Los ensayos se efectuaron aplicando cargas normales entre 2, 5 y 15 N. Se encontró que la velocidad de desgaste se incrementa con la carga aplicada en los materiales irradiados con bajas dosis, mientras que aquellos irradiados con las dosis más altas la velocidad de desgaste atraviesa por un valor máximo con la carga. The aim of this study was to determine the sliding wear behavior of γ-irradiated linear polyethylene. The polymers used were two linear polyethylenes that were irradiated by γ rays at room temperature. Equal total doses of 2, 5, 10 and 20 Mrad were applied. Tribological tests were performed in a Pin On Disc tribometer with normal loads between 2, 5 and 15 N. The results show that the wear rate increases with the applied load in the case of the samples irradiated with the lowest doses, while the wear rate displays a maximum with the applied load in the samples irradiated with the highest dose.
机译:这项工作的目的是评估受到伽玛射线滑动磨损的聚乙烯的行为。这些使用两种线性聚乙烯,它们在室温下用伽马射线辐照,每组分别施加2、5、10和20 Mrad的剂量。摩擦学研究使用Pin On Disc摩擦计进行。测试是在2、5和15 N的正常载荷下进行的。发现,随低剂量辐照的材料施加的载荷,磨损率会增加,而受到最高剂量辐照的材料的磨损率会通过随负载的最大值。这项研究的目的是确定γ辐照线性聚乙烯的滑动磨损性能。所用的聚合物是两种γ射线辐照的线性聚乙烯。在室温下发出光线。相等的总剂量分别为2、5、10和20 Mrad。摩擦测试是在销钉盘式摩擦计中进行的,正常载荷在2、5和15 N之间。结果表明,在样品受到最低剂量照射的情况下,磨损率随施加的载荷而增加,而磨损率显示最高剂量照射的样品中施加的负载最大。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号