首页> 外文会议>Joint Rail Conference >Lateral stability performance in uni-directional rollingstock
【24h】

Lateral stability performance in uni-directional rollingstock

机译:单向轧机中的横向稳定性性能

获取原文

摘要

The worn wheel profiles generated by uni-directional wagon travel produce different profile shapes on the leading and trailing wheelsets of each bogie. In the case examined both leading and trailing wheels wear to profiles having greater effective wheel conicity. The leading worn wheels exhibit flange and tread wear and the worn profile has highly nonlinear conicity having little vertical displacement over the middle range of lateral displacement. A large vertical displacement is still achieved by the worn leading wheel profile in the last section of the flangeway clearance. The worn trailing wheels have only tread wear with near linear effective conicity across the flangeway. The hunting instability performances of the vehicle with the uni-directional wheel wear profiles is shown to have a higher critical speed than new wheel profiles due to the mismatch of the leading and trailing wheel profiles. The leading wheels of the bogie hunt with a wavelength of 26-30 m whilst the trailing wheels hunt at a wavelength of 12-16 m. Because of the differing frequency responses in the front and rear wheelsets of each bogie, lateral instability is damped for the worn wheel profiles. The worn profiles' curving performance is also improved due to increases in the total profile conicity. Individually the leading wheel worn profile with its nonlinear conicity across the flangeway has lower critical speed than a new wheel profile, the non-linear shape leading to chaotic lateral instability. The trailing wheel profile with its highly linear conicity across the middle of the flangeway has classic sinusoidal hunting at a much reduced critical speed and much reduced wavelength. The worn wheel profiles by themselves for both leading wheel and trailing wheel are found to have critical speeds 80% of the new wheel profile critical speed. In combination as found in a wagon operating in one direction, the leading and trailing wheel profiles produce a critical hunting speed 125% of the new wheel profiles' critical hunting speed.
机译:由单向马车行程产生的破旧轮廓在每个转向架的前导和尾随轮上产生不同的轮廓形状。在案例中,两者都磨损到具有更大有效轮型的曲线的曲线。领先的磨损轮表现出法兰和胎面磨损,磨损的轮廓具有高度非线性的,在横向位移的中间范围内具有很小的垂直位移。在Flangeway间隙的最后一部分中,磨损的前轮轮廓仍然可以实现大的垂直位移。穿着的后轮只有胎面磨损,靠近线性的近线有效的结合在整个气球。由于前轮和后轮轮廓不匹配,具有单向车轮磨损型材的车辆的捕冲不稳定性表现具有比新轮廓更高的临界速度。波长的前轮以波长为26-30米,而尾随车轮在波长为12-16米。由于每个转向架的前后轮和后轮的频率响应不同,横向不稳定性被损害磨损的轮廓。由于总型材的性是显着性的增加,磨损的曲线弯曲性能也得到改善。单独的前轮磨损轮廓具有其非线性圆形的非线性曲线具有比新的车轮轮廓更低的临界速度,导致混沌横向不稳定性的非线性形状。尾随车轮轮廓具有跨越幻灯道中间的高线性结合,具有经典的正弦狩猎,其临界速度大大降低,波长大大降低。对于前轮和后轮的自身磨损的轮廓突破具有临界速度的新轮廓临界速度的临界速度。结合在一个在一个方向上操作的无盖货车中发现,前缘和后轮型材产生了新轮廓的关键狩猎速度125%的临界狩猎速度。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号