首页> 外文会议>ASME conference on smart materials, adaptive structures and intelligent systems >MODELING AND EXPERIMENT OF A FLEXIBLE MODULE ACTUATED BY SHAPE MEMORY ALLOY WIRE
【24h】

MODELING AND EXPERIMENT OF A FLEXIBLE MODULE ACTUATED BY SHAPE MEMORY ALLOY WIRE

机译:形状记忆合金线驱动的柔性模块的建模与实验

获取原文

摘要

In recent years many investigations have been performed on design and fabrication of micro mechanical manipulators. One of the practical usages of this manipulator is endoscopy. In an endoscopy system, a small manipulator with high maneuverability and flexibility is required to support the probe's movement into a colon easier than classic manipulators. In this paper a basic flexible module is presented for use in such an application. The structure of presented module is simple and includes a compressive spring which could be bent to the sides. This tends to more simplicity in addition to proper flexibility. Connecting three wires of shape memory alloy (SMA) uniformly distributed in circumference of spring with an angle of 120 degrees, it is possible to provide an almost large displacement and orientation change between the end planes of module. By using three wires and stimulating them individually or together, different rotation regimes are provided. The flexible module deformation is modeled in this paper thoroughly. Deflection and orientation of spring as the basic structure of the module is studied under the loads. Also, Brinson model is used for modeling the shape memory alloy wire. Afterward, the spring model is coupled with SMA model to describe the dynamic behavior of module under a defined activation. The simulation is implemented in MATLAB-Simulink Though the developed simulation platform, the trajectory of module may be extracted and used for developing a modular manipulator. An experimental setup is prepared to verify the simulation results. Through the simulations, module performance in addition to proper geometrical parameters for the considered application is calculated through the simulations. It is shown that a proper relation between geometrical parameters of spring (like outer diameter, spring wire diameter and number of coils) in combination with a suitable SMA wire in diameter, affect the maximum deformation of SMA-actuated module.
机译:近年来,已经对微型机械操纵器的设计和制造进行了许多研究。该操纵器的实际用途之一是内窥镜检查。在内窥镜系统中,需要一个具有较高可操纵性和灵活性的小型操纵器,以比传统操纵器更容易地支持探头移入结肠。在本文中,提出了用于此类应用的基本柔性模块。提出的模块的结构很简单,并包括一个可以向侧面弯曲的压缩弹簧。除了适当的灵活性之外,这还趋于更加简单。将形状记忆合金(SMA)的三根导线以120度的角度均匀地分布在弹簧的圆周上,可以在模块的端面之间提供几乎很大的位移和方向变化。通过使用三根导线并单独或一起刺激它们,可以提供不同的旋转方式。本文对柔性模块的变形进行了全面建模。研究了在载荷作用下作为模块基本结构的弹簧的挠度和方向。而且,布林森模型用于对形状记忆合金线进行建模。然后,将弹簧模型与SMA模型耦合以描述模块在定义的激活下的动态行为。该仿真是在MATLAB-Simulink中实现的。尽管开发了仿真平台,但可以提取模块的轨迹并将其用于开发模块化机械手。准备了一个实验装置来验证仿真结果。通过仿真,通过仿真可以计算出模块性能以及适用于所考虑应用的适当几何参数。结果表明,弹簧的几何参数(如外径,弹簧线直径和线圈数量)与合适的SMA线直径的适当关系会影响SMA驱动模块的最大变形。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号