【24h】

Edge-based Refactored EPC for High Speed Mobility

机译:基于边缘的EPC高速移动性

获取原文

摘要

The current design of LTE is to deploy the EPC components in a core network, and the data traffic from UEs (User Equipment) is converged to these components. It will cause network congestion and inefficiencies with the increasing number of internet devices in the future. One distributed way to solve the network burden is to deploy the on demand EPC components close to the edge of network (near the base station; known as Edge-based EPC). At present, some researches directly use the current EPC components for edge deployment. However, it causes some problems. When a UE moves between two edge networks, it will face the inter-edge procedures to change of these serving edge components. The procedure involves many numbers of message exchanges between components for the re-establishment of the connection, which will affect the UE's experience. It represents that the current EPC architecture is not suitable for edge deployment. Based on our previous study, we had derived a Refactored EPC (R-EPC) architecture [1]. Then, we determine the deployment of the R-EPC components based on their responsibilities and call this architecture edge-based refactored EPC (abbreviated to E-R-EPC). In E-R-EPC, we deploy the common use of service triggering related components and the gateway responsible for data traffic to edge network, while deploying the components that record the location of UE to core network; thus, the UE can use the low-latency data traffic services in edge network, since the served recording location components are not changed, it can reduce the signaling cost to update the location information. Also, we propose a new handover procedure called inter-edge handover. Further, we compare the signaling cost and queuing delay of E-R-EPC with other architectures, the results of the proposed one showed good performance, especially in dealing with frequent movements of UE between two edge networks (e.g.: high-speed mobility); It proves E-R-EPC is a suitable reference for edge-designed networks.
机译:LTE的当前设计是将EPC组件部署在核心网络中,并且来自UE(用户设备)的数据业务被汇聚到这些组件。将来随着越来越多的互联网设备,这将导致网络拥塞和效率低下。解决网络负担的一种分布式方法是将按需EPC组件部署在靠近网络边缘(在基站附近;称为基于边缘的EPC)附近。目前,一些研究直接将当前的EPC组件用于边缘部署。但是,这会引起一些问题。当UE在两个边缘网络之间移动时,它将面临边缘间过程以更改这些服务边缘组件。该过程涉及组件之间的许多消息交换以重建连接,这将影响UE的体验。它表示当前的EPC体系结构不适合边缘部署。根据我们先前的研究,我们得出了重构EPC(R-EPC)架构[1]。然后,我们根据其职责确定R-EPC组件的部署,并将此架构称为基于边缘的重构EPC(缩写为E-R-EPC)。在E-R-EPC中,我们将服务触发相关组件和负责数据流量的网关部署到边缘网络,同时将记录UE位置的组件部署到核心网络。因此,UE可以在边缘网络中使用低等待时间的数据业务,因为所服务的记录位置分量没有改变,因此可以减少信令信息更新位置信息。另外,我们提出了一种新的切换过程,称为边缘间切换。此外,我们将E-R-EPC的信令成本和排队延迟与其他架构进行了比较,提出的结果显示出良好的性能,尤其是在处理UE在两个边缘网络之间频繁移动的情况下(例如:高速移动性);证明E-R-EPC是边缘设计网络的合适参考。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号