Experimental Research on the Measurement on line of the Actual Temperature and blacking of Hot Rolling Sheet

机译：热轧板实际温度和发黑度在线测量的实验研究

获取原文

获取原文并翻译 | 示例

页面导航

摘要
著录项
相似文献
相关主题

摘要

About practical radiate measurement of temperature, the radiation power of the object is relatedn ot only to the temperature, but also to the blacking. Furthmore, the blacking that is unknown or changeable constantly, which acts as interference has remained a real problem in radiate measurement of temperature. And emitting is related to many factors. In this case, the measurement of blacking on line is of great importance.

机译：关于温度的实际辐射测量，物体的辐射功率不仅与温度有关，而且与发黑有关。此外，未知的或不断变化的发黑现象（作为干扰）一直是辐射温度测量中的实际问题。排放与许多因素有关。在这种情况下，在线黑化的测量非常重要。

著录项

来源
《Fourth International Conference on Measurement and Control of Granular Materials (MCGM'97) September 17-19, 1997 Shenyang, P.R.China》|1997年|p.154-156|共3页
会议地点 Shenyang(CN);Shenyang(CN)
作者
Liu yongsheng; Liu zijing; Wei Yingjie; Wen shaofei;
展开▼
作者单位

展开▼
会议组织
原文格式 PDF
正文语种 eng
中图分类一般工业技术;
关键词
入库时间 2022-08-26 14:01:24

相似文献

外文文献
中文文献
专利

1. Enhancement of stretch formability of Mg-3Al-1Zn alloy sheet using hot rolling at high temperatures up to 823 K and subsequent warm rolling [J] . Xinsheng Huang, Kazutaka Suzuki, Naobumi Saito Scripta materialia . 2009,第4期

机译：通过在高达823 K的高温下热轧并随后进行热轧，可增强Mg-3Al-1Zn合金板的拉伸成形性
2. Effects of Chemical Composition and Rough Rolling Temperature on Deep Drawability of Extra Low C Sheet Steels with Hot Rolling at Ferrite Region [J] . Hidetaka Kawabe 材料とプロセス: 日本鉄鋼協会講演論文集 . 1996,第3期

机译：化学成分和粗轧温度对铁素体区热轧超低碳薄钢板深冲性的影响
3. Effects of Chemical Composition and Rough Rolling Temperature on Deep Drawability of Extra Low C Sheet Steels with Hot Rolling at Ferrite Region [J] . Hidetaka Kawabe 材料とプロセス: 日本鉄鋼協会講演論文集 . 1996,第3期

机译：化学成分及粗糙轧制温度对铁素体区热轧钢材钢材钢材深度拉伸性的影响
4. Experimental Research on the Measurement on line of the Actual Temperature and blacking of Hot Rolling Sheet [C] . Liu yongsheng, Liu zijing, Wei Yingjie, International conference on measurement and control of granular materials . 1997

机译：热轧板实际温度和黑色线测量的实验研究
5. An experimental study of hot rolling with low finishing temperature of an extra-low carbon steel. [D] . Hwu, Yhu-Jen. 1995

机译：超低碳钢低终轧温度热轧的实验研究。
6. Effect of Final Rolling Temperature on Microstructures and Mechanical Properties of AZ31 Alloy Sheets Prepared by Equal Channel Angular Rolling and Continuous Bending [O] . Laixin Shi, Lei Liu, Li Hu, 2020

机译：最终轧制温度对等通道角轧制和连续弯曲制备的AZ31合金板微结构和力学性能的影响
7. Measurement of actual stress and temperature on the roll surface during rolling. Measurement of temperature and heat flux distribution on the roll surface in cold rolling. [O] . Yotaro HATAMURA, Takesi YONEYAMA 1989

机译：轧制过程中辊表面上的实际应力和温度的测量。冷轧辊表面温度和热通量分布的测量。
8. Final report on numerical simulation of processes of hot sheet bending in the frame of the project EUREKA-FASP (EU353). v. 3. Pt. 5. Pt. 6. New source representation obtained by comparison with experimental temperature data; Parametric analyses of area heating processes in the sheet hot bending [R] . Carmignani, B. , Toselli, G. 1996

机译：关于EUREKa-Fasp（EU353）项目框架中热板弯曲过程数值模拟的最终报告。 v.3。pt。 5. pt。 6.通过与实验温度数据比较获得的新源表示;板材热弯曲区域加热过程的参数分析

Experimental Research on the Measurement on line of the Actual Temperature and blacking of Hot Rolling Sheet

摘要

著录项

相似文献

相关主题

期刊订阅