美国给水工程协会_国内外标准网文献检索下载

1.[标准] Magnetic Inductive Flowmeters

磁感应流量计

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C751-19

发布时间：
2020-04-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this document is to review magnetic inductive flowmeter (magmeter) principles of operation, calibration, and selection. The performance and the reliability of these meters with no moving parts will be discussed. The meters require less maintenance and are more accurate than mechanical meters in use today. Magmeters are used in a wide variety of applications including the measurement of wastewater, raw water, treated water, and revenue generation and in different stages of the treatment process such as the measurement of settled water, supernatant water, and backwash water and for proportional chemical addition (pacing). These meters have also been widely used in large-diameter intercity custody transfer pipeline applications.
2.[标准] Transit-Time Flowmeters in Full Closed Conduits

全封闭管道中的渡越时间流量计

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C750-19

发布时间：
2020-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard describes transit-time ultrasonic flowmeters for water supply service application in pipes running full. An ultrasonic flowmeter is a meter that uses acoustic energy signals to measure liquid velocity. There are currently two distinct types of ultrasonic flowmeters available: Doppler-effect and transit-time. The Doppler-effect meter is used exclusively for liquids containing solid particles or gases, and the transit-time flowmeter is used in a wide variety of applications in the water industry.
3.[标准] Tendon-Prestressed Concrete Water Tanks

预应力钢筋混凝土水箱

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA D115-20

发布时间：
2020-07-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to provide the minimum requirements for fiberglass pressure pipe, including design, fabrication, and testing requirements. This standard can be referenced in specifications for purchasing and receiving fiberglass pressure pipe. This standard can be used as a guide for manufacturing this type of fiberglass pressure pipe. The stipulations of this standard apply when this document has been referenced and then only to fiberglass pressure pipe.
4.[标准] Stainless-Steel Pipe Flange Joints for Water Service - Sizes 2 In. Through 72 In. (50 mm Through 1,800 mm)

供水用不锈钢管法兰接头.尺寸2英寸通过72英寸（50毫米至1800毫米）

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C228-19

发布时间：
2019-04-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to provide the minimum requirements for quicklime and hydrated lime, including physical, chemical, sampling, packaging, shipping, and testing requirements.This standard can be referenced in documents for purchasing and receiving quicklime and hydrated lime and can be used as a guide for testing the physical and chemical properties of quicklime and hydrated lime samples. The stipulations of this standard apply when this document has been referenced and then only to quicklime and hydrated lime used in the treatment of potable water, wastewater, or reclaimed water.
5.[标准] Fabricated Steel and Stainless Steel Tapping Sleeves

装配式钢和不锈钢攻丝套筒

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C223-19

发布时间：
2019-05-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to provide minimum requirements for stainless steel and ductile-iron body knife gate valves with resilient and metal seats, including tapping knife gate valves, for use in water, wastewater, and reclaimed water systems, including materials, design, testing, rejection, marking, and shipping.
6.[标准] Factory-Coated Bolted Steel Tanks for Water Storage

工厂涂装的栓接钢制储水箱

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA D103-19

发布时间：
2019-07-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to provide minimum requirements for the design, construction, inspection, and testing of new cylindrical, factory-coated, bolted carbon steel tanks for the storage of water. This standard is only applicable to tanks with a base elevation substantially at ground level. This standard does not cover all details of design and construction. Details that are not addressed shall be designed and constructed to be as adequate and as safe as those that would otherwise be provided under this standard. This standard is not applicable to tanks of corrugated construction. This standard is not applicable to tanks constructed of stacked plates or sheets laminated to form multiple layers.
7.[标准] Thermosetting Fiberglass-Reinforced Plastic Tanks

热固性玻璃纤维增强塑料罐

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA D120-19

发布时间：
2019-10-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to provide purchasers, manufacturers, and suppliers with the minimum requirements for thermosetting FRP tanks, including material and design. This standard can be referenced in specifications for purchasing and receiving thermosetting FRP tanks.This standard can be used for manufacturing this type of tank. The stipulations of this standard apply when this document has been referenced, and then only to FRP tanks.
8.[标准] Electrodialysis and Ion-Exchange Membrane Systems

电渗析和离子交换膜系统

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA B116-19

发布时间：
2019-08-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard sets minimum requirements for ion-exchange membrane (IEM) systems such as electrodialysis (ED), electrodialysis reversal (EDR), electrodialysis metathesis (EDM), and electrodeionization (EDI) used for water and reclaimed water treatment systems.This standard can be referenced for design, procurement, installation, and commissioning of IEM systems used for water and reclaimed water treatment systems.
9.[标准] Plastic Ball Valves

塑料球阀

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C521-18

发布时间：
2019-01-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to define the minimum requirements for water supply service plastic ball valves, including materials, design, testing, and shipping.This standard describes plastic ball valves for water supply service. This standard covers threaded, union, fusion, or compression ended double- and single-seated nonmetallic ball valves for pressures 100 psi (689 kPa) and higher in sizes from ½-in. through 2-in. (13-mm through 50-mm) diameter for use in potable water systems with temperatures greater than 32°F (0°C) and less than 125°F (52°C).
10.[标准] Stainless Steel Fittings for Waterworks Service, Sizes 1/2 In. Through 72 In. (15 mm Through 1800 mm)

供水设施用不锈钢配件尺寸1/2英寸通过72英寸（15毫米至1800毫米）

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C226-19

发布时间：
2019-07-01

中标分类：
-

国标分类：
-

实施时间：
11.[标准] Quicklime and Hydrated Lime

生石灰和熟石灰

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA B202-19

发布时间：
2019-04-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to provide the minimum requirements for quicklime and hydrated lime, including physical, chemical, sampling, packaging, shipping, and testing requirements.This standard can be referenced in documents for purchasing and receiving quicklime and hydrated lime and can be used as a guide for testing the physical and chemical properties of quicklime and hydrated lime samples. The stipulations of this standard apply when this document has been referenced and then only to quicklime and hydrated lime used in the treatment of potable water, wastewater, or reclaimed water.
12.[标准] Microfiltration and Ultrafiltration Membrane Systems

微滤和超滤膜系统

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA B112-19

发布时间：
2019-05-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to provide a minimum set of requirements for MF and UF systems used for water and reclaimed water filtration systems. This standard is intended to assist with the design, procurement, installation, and commissioning of MF and UF systems.
13.[标准] Liquid Oxygen for Ozone Generation for Water, Wastewater, and Reclaimed Water Systems

用于水、废水和再生水系统臭氧生成的液氧

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
历史

标准号：
AWWA B304-18

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this standard is to provide the minimum requirements for LOX intended for water, wastewater, and reclaimed water systems. This standard includes physical, chemical, packaging, shipping, sampling, and testing requirements.This standard can be referenced in purchase documents for LOX and can be used as a guide for sampling and testing the physical and chemical properties of LOX samples. The stipulations of this standard apply when this document has been referenced and then only for LOX used for generation of ozone for water supply applications and in the treatment of potable water, wastewater, or reclaimed water.
14.[标准] Tape Coatings for Steel Water Pipe and Fittings

钢制水管和管件用胶带涂层

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C209-19

发布时间：
2019-12-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard describes protective coatings that consist of liquid adhesives and tapes and their applications to steel water pipe and fittings to be used for underground and underwater pipelines. Tape coatings conforming to this standard may be field- or shop-applied, without the use of heat (i.e., not hot-applied coatings), to uncoated pipe and fittings or as a joint coating to pipe and fittings protected with organic coatings. These liquid adhesives and tapes are not intended for use with either exposed steel joints or sections of steel pipe where coating of cement mortar or concrete has been applied directly onto the bare steel pipe.
15.[标准] Contact-Molded, Fiberglass-Reinforced Plastic Wash-Water Troughs and Launders

接触模制玻璃纤维增强塑料洗涤水槽和流槽

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA F101-19

发布时间：
2019-06-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard describes the minimum requirements for fiberglass-reinforced plastic wash-water troughs and launders made by the contact-molding process, including flat-bottom, round-bottom, and V-bottom troughs and launders. Requirements are included for materials, properties, design, construction, dimensions, tolerances, work quality, and appearance.This standard also describes the requirements for using general-purpose and chemical-resistant resins. These fabrications are generally used in municipal water supply service and industrial water supply service applications.
16.[标准] Knife Gate Valves, Sizes 2 In. (50 mm) Through 96 In. (2,400 mm)

刀闸阀尺寸为2英寸（50毫米）至96英寸（2400毫米）

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C520-19

发布时间：
2019-05-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard describes fabricated steel and stainless-steel tapping sleeves used to provide outlets and branches on existing pipe with or without interruption of service. They are intended for pipe sizes 4 in. (100 mm) through 48 in. (1,200 mm) with branch outlets through 36 in. (900 mm). This standard includes requirements for materials, dimensions, tolerances, finishes, and testing.
17.[标准] Matched-Die Molded, Fiberglass-Reinforced Plastic Weir Plates, Scum Baffles, and Mounting Brackets

匹配的模压玻璃纤维增强塑料堰板、浮渣挡板和安装支架

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA F102-19

发布时间：
2019-05-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard describes the minimum requirements for fiberglass-reinforced plastic weir plates, scum baffles, mounting brackets, lap plates, cover washers, and weir pans, fabricated with the matched-die molding process. Included are requirements for design, construction, dimensions, tolerances, physical properties, work quality, appearance, and installation. This standard contains the requirements for using general-purpose and chemical-resistant resins. These fabrications are generally used in municipal water supply service and industrial water supply service applications.This standard can be referenced in specifications for matched-die-molded, fiberglass-reinforced plastic weir plates, scum baffles, and mounting brackets. The stipulations of this standard apply when this document has been referenced and then only to matched-die-molded, fiberglass-reinforced plastic weir plates, scum baffles, and mounting brackets.
18.[标准] Aluminum Dome Roofs for Water Storage Facilities

储水设施用铝穹顶

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA D108-19

发布时间：
2019-11-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard establishes minimum criteria for the design, fabrication, and erection of structurally supported aluminum dome roofs. Aluminum dome roofs can be used on any size tank erected in accordance with AWWA standards. When this standard is specified, in the case of conflict between this standard and any other standard, the requirements of this standard shall govern. The dome shall be a spherical structure conforming to the dimensions of the tank. The tank shall be designed to support the aluminum dome roof.
19.[标准] Metal-Seated Gate Valves for Water Supply Service

供水用金属阀座闸阀

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C500-19

发布时间：
2019-06-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard describes iron-body, metal-to-metal seated, nonrisingstem (NRS) gate valves, including tapping gate valves, 3 in. (75 mm) through 72 in. (1,800 mm), and outside screw and yoke (OS&Y) rising-stem gate valves, 3 in. (75 mm) through 72 in. (1,650 mm), with either double-disc gates having parallel or inclined seats, or solid-wedge gates.These valves are suitable for use in approximately level settings within water systems. These valves are intended for applications where fluid velocities do not exceed 16 ft/sec (4.9 m/sec) when the valve is in the fully open position.
20.[标准] Ductile-Iron Compact Fittings

球墨铸铁紧固件

发布单位：
美国-美国给水工程协会(US-AWWA)

标准状态：
现行

标准号：
AWWA C153/A21.53-19

发布时间：
2019-11-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard describes 3-in. through 64-in. (80-mm through 1,600-mm) ductile-iron compact fittings to be used with ductile-iron pipe or pipe made of other materials with similar outside diameters for conveying potable water, wastewater, and reclaimed water. Fittings with mechanical joints are listed in this standard for the 3-in. through 64-in. (80-mm through 1,600-mm) sizes. Fittings with push-on joints and flanged joints are listed in this standard for the 54-in. through 64-in. (1,400-mm through 1,600-mm) sizes.