美国焊接协会_国内外标准网文献检索下载

1.[标准] Specification for Automotive Weld Quality - Arc Welding of Steel

汽车焊接质量规范.钢的电弧焊

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS D8.8M:2021

发布时间：
2021-01-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This specification describes weld geometry and workmanship criteria essential to ensure the quality of automotive and light truck weldments. This specification covers the arc and hybrid arc welding of coated and uncoated steels.
2.[标准] Specification for Carbon Steel Electrodes and Rods for Gas Shielded Arc Welding

气体保护电弧焊用碳钢焊条和焊条规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS A5.18/A5.18M:2021

发布时间：
2021-01-01

中标分类：
-

国标分类：
-

实施时间：
3.[标准] Specification for Friction Stir Welding of Aluminum Alloys for Aerospace Applications

航空航天用铝合金搅拌摩擦焊接规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS D17.3/D17.3M:2021

发布时间：
2021-01-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS D17.3/D17.3M:2021 covers the general requirements for the friction stir welding of aluminum alloys for aerospace applications. It includes the requirements for weldment design, qualification of personnel and procedures, fabrication, and inspection.
4.[标准] Bridge Welding Code (Joint Publication with AASHTO)

桥梁焊接规范（与AASHTO联合出版）

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS D1.5M/D1.5:2020

发布时间：
2020-01-01

中标分类：
-

国标分类：
-

实施时间：

摘要： This code covers the welding requirements for welded bridges made from carbon and low-alloy constructional steels and designed to AASHTO or AREMA requirements. This 2020 edition contains dimensions in metric SI Units and U.S. Customary Units. Clauses 1 through 9 constitute a body of rules for the regulation of welding in steel construction. Clauses 10 and 11 do not contain provisions, as their analogue D1.1 sections are not applicable to the D1.5 code. Clause 12 contains the requirements for fabricating fracture critical members.
5.[标准] Standard WPS for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1 1/2' Thick, E7018, As-Welded or PWHT Condition, Primarily Pipe Applications

1/8至1/2“厚的E7018焊态或焊后热处理条件下碳钢（M-1/P-1/S-1 第1组或第2组）的保护金属极电弧焊标准WPS 主要用于管道应用

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-208:2019

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-208:2019 contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for pipe applications.
6.[标准] Standard Welding Procedure Specification for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4' Thick, E6010 (Vertical Uphill), As-Welded Condition, Primarily Pipe Applications

1/8至3/4“厚E6010（垂直上坡）焊态碳钢（M-1/P-1/S-1 第1组或第2组）的保护金属极电弧焊标准焊接工艺规范主要用于管道应用

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-203:2019

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-203:2019 contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 3/4 inch [19 mm], using manual shielded metal arc welding with E6010 (vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for pipe applications.
7.[标准] Standard Welding Procedure Specification for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4' Thick, E6010 (Vertical Uphill) Followed by E7018 (Vertical Uphill), As-Welded Condition, Primarily Pipe Applications

1/8至3/4“厚E6010（垂直向上）和E7018（垂直向上）碳钢（M-1/P-1/S-1 第1组或第2组）焊接状态下主要用于管道应用的保护金属极电弧焊标准焊接工艺规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-201:2019

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-201:2019 contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 3/4 inch [19 mm], using manual shielded metal arc welding with E6010 (vertical uphill) followed by E7018 (vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for pipe applications.
8.[标准] Standard WPS for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1 1/2' Thick, E6010 (Vertical Downhill), Followed by E7018 (Vertical Uphill) As-Welded or PWHT Condition, Primarily Pipe Applications

1/8至1/2“厚E6010（垂直下坡）碳钢（M-1/P-1/S-1 第1组或第2组）的保护金属极电弧焊标准WPS 然后是E7018（垂直上坡）焊态或焊后热处理状态主要用于管道应用

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-206:2019

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-206:2019 contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual shielded metal arc welding with E6010 (vertical downhill) followed by E7018 (vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for pipe applications.
9.[标准] Railroad Welding Specification for Cars and Locomotives

铁路车辆和机车焊接规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS D15.1/D15.1M:2019

发布时间：
2019-03-08

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS D15.1/D15.1M:2019 establishes minimum welding standards for the manufacture and maintenance of railcars, locomotives, and their components, intended for North American railroad service. Clauses 4 through 17 cover the general requirements for welding in the railroad industry. Clauses 18 through 23 cover specific requirements for the welding of base metals thinner than 1/8 in [3 mm].
10.[标准] Standard WPS for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4' Thick, E6010 (Vertical Downhill Root with the Balance Vertical Uphill), As-Welded Condition, Primarily Pipe Applications

1/8至3/4“厚E6010（垂直下坡根部平衡垂直上坡）碳钢（M-1/P-1/S-1 第1组或第2组）的保护金属极电弧焊标准WPS 焊接状态主要用于管道应用

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-204:2019

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-204:2019 contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 3/4 inch [19 mm], using manual shielded metal arc welding with E6010 (vertical downhill root with the balance vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for pipe applications.
11.[标准] Specification for the Qualification of Resistance Welding Technicians

电阻焊技术人员资格认证规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS C1.5:2019

发布时间：
2019-06-14

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS C1.5:2019 establishes qualification requirements for a resistance welding technician (RWT). It describeshow qualifications are determined, and the practice by which qualification may be attained and maintained. The user of this specification will evaluate the qualifications of each candidate, and provide examinations to test the candidate's resistance welding skills and knowledge, as well as, his or her ability to apply the principles of resistance welding.This specification is intended to supplement the minimum requirements of employers, codes, other standards, ordocuments, and shall not be construed as a preemption of the employer's responsibility for the work or for the performance of the work. Resistance welding processes include spot welding, projection welding, seam welding, butt welding, flash welding, micro joining, resistance brazing, resistance soldering and resistance heating.It is understood not all of these disciplines are used in every situation and it shall be the responsibility of employers to determine their employee, who having qualified as a RWT, is capable of performing the specific duties involved in their career assignments. While the RWT has established excellent credentials, qualification to this specification alone may not legally qualify the technician to provide technical services to the public. Contract documents and building or jurisdiction laws may require technical services to be performed under the direction and responsibility of others such as a registered Professional Engineer (P.E.). The RWT designation DOES NOT imply the status of a registered P.E. under the laws of any state or other governmental entity.
12.[标准] Standard WPS for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 3/4' Thick, E6010 (Vertical Downhill) Followed by E7018 (Vertical Uphill), As-Welded Condition, Primarily Pipe Applications

1/8至3/4“厚E6010（垂直下坡）和E7018（垂直上坡）碳钢（M-1/P-1/S-1 第1组或第2组）的保护金属极电弧焊标准WPS 焊接状态主要用于管道应用

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-202:2019

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-202:2019 contains the essential welding variables for carbon steel in the thickness range of 1/8 through 3/4 inch, using manual shielded metal arc welding with E6010 (vertical downhill) followed by E7018 (vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This WPS was developed primarily for pipe applications.
13.[标准] Specification for Welding Earthmoving, Construction and Agricultural, and Ground-Based Material Handling Equipment

焊接土方、建筑、农业和地面材料搬运设备规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS D14.3/D14.3M:2019

发布时间：
2019-02-28

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS D14.3/D14.3M:2019 provides standards for producing structural welds used in the manufacture of earthmoving, construction, and agricultural equipment. Such equipment is defined as self-propelled, on- and off-highway machinery and associated implements. Manufacturers responsibilities are presented as they relate to the welding practices that have been proven successful within the industry in the production of weldments on this equipment. Basic dimensional weld details are defined and interpreted for application throughout the document. Provisions are made to identify base metals used in these weldments. Procedures to assure they are welded with compatible, identifiable welding processes and consumables are included with consideration given to factors that affect weldability.
14.[标准] Standard Welding Procedure Sspecification (WPS) for; Gas Tungsten Arc Welding of Carbon Steel (M-1/P-1/S-1, group 1 or 2), 1/8 through 1-1/2' think, ER70S-2, as-Welded or PWHT Ccondition (primarily pipe applications)

标准焊接工艺规范（WPS）；碳钢的钨极气体保护焊（M-1/P-1/S-1 第1组或第2组） 1/8至1-1/2英寸 ER70S-2 焊前或焊后热处理条件（主要是管道应用）

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-207:2019

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-207:2019 contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual gas tungsten arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for pipe applications.
15.[标准] Specification for Classification of Weld-Through Paint Primers

透焊涂料底漆分类规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS D3.9/D3.9M:2019

发布时间：
2019-05-14

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS D3.9/D3.9M:2019 prescribes the requirements for the classification of weld-through paint primers. The classification is based on paint film thickness and welding procedure. Manufacturers may classify their products to different film thicknesses or welding procedures if they provide the details of their tests.
16.[标准] Standard WPS for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1 1/2' Thick, E6010 (Vertical Uphill), Followed by E7018 (Vertical Uphill), As-Welded or PWHT Condition, Primarily Pipe Applications

1/8至1/2“厚E6010（垂直向上）碳钢（M-1/P-1/S-1 第1组或第2组）的保护金属极电弧焊标准WPS 然后是E7018（垂直向上）焊态或焊后热处理状态主要用于管道应用

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-205:2019

发布时间：
2019-03-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-205:2019 contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual shielded metal arc welding with E6010 (vertical uphill) followed by E7018 (vertical uphill). It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for pipe applications.
17.[标准] Specification for the Design of Welded Joints in Machinery and Equipment

机械和设备焊接接头设计规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS D14.4/D14.4M:2019

发布时间：
2019-01-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS D14.4/D14.4M:2019 sets forth requirements dealing with the allowable stresses, welded joint design, workmanship, procedure and performance qualification, inspection, repair and post weld treatments of welded connections used in machinery and equipment, subject to static and cyclic loading. It is intended to be used in conjunction with other specifications that provide application specific requirements (such as D14.1, D14.3, etc.). In the event a conflict arises between the application specific standard and AWS D14.4/D14.4M, the application specific standard shall take precedence. The intent of this document is to establish the effect of weld joint geometry, welding practices, and quality control on allowable stress levels. The specification also provides practices that can be used for examination of welded joints used in fabrication of machinery and equipment.
18.[标准] Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2), 1/8 inch 3 mm through 1-1/2 inch 38 mm Thick, E6010 (Vertical Downhill) Followed by E7018, As-Welded or PWHT Condition, Primarily Plate and Structural Application

1/8英寸[3 mm]至1-1/2英寸[38 mm]厚E6010（垂直下坡）和E7018焊态或焊后热处理条件下碳钢（M-1/P-1 第1组或第2组）的保护金属极电弧焊标准焊接工艺规范（SWPS）主要用于板材和结构应用

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS B2.1-1-026:2018

发布时间：
2018-04-10

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS B2.1-1-026:2018 contains the essential welding variables for carbon steel in the thickness range of 1/8 through 1-1/2 inch, using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications.
19.[标准] Guide for Joining of Solid Solution Austenitic Stainless Steels

固溶奥氏体不锈钢连接指南

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
现行

标准号：
AWS G2.3M/G2.3:2019

发布时间：
2018-08-16

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS G2.3M/G2.3:2019 presents a description of wrought solid solution austenitic stainless steels and the processes and procedures that can be used for the joining of these materials.This standard discusses the welding processes and welding parameters, qualifications, inspection and repair methods, cleaning, and safety considerations. Practical information has been included in the form of figures, tables, and graphs that should prove useful in determining capabilities and limitations in the joining of austenitic stainless steels.
20.[标准] Specification for Carbon Steel Electrodes and Rods for Gas Shielded Arc Welding

气体保护电弧焊用碳钢焊条和焊条规范

发布单位：
美国-美国焊接协会(US-AWS)

标准状态：
历史

标准号：
AWS A5.18/A5.18M:2017

发布时间：
2018-07-01

中标分类：
-

国标分类：
-

实施时间：

摘要： AWS A5.18/A5.18M:2017 prescribes the requirements for classification of solid carbon steel electrodes and rods, composite stranded carbon steel electrodes, and composite metal cored carbon steel electrodes for gas shielded arc welding. Classification is based on chemical composition of the electrode for solid electrodes and rods, chemical composition of weld metal for composite stranded and composite metal cored electrodes and the as-welded mechanical properties of the weld metal for each. Additional requirements are included for manufacturing, diameters, lengths, and packaging. A guide is appended to the specification as a source of information concerning the classification system employed and the intended use of the electrodes and rods. This specification makes use of both U.S. Customary Units and the International System of Units (SI). Since these units are not equivalent, each system must be used independently of the other.