安全行业协会_国内外标准网文献检索下载

1.[标准] Acoustic Glassbreak Detector Standard - Features for Optimizing False Alarm Reduction and Detection

声学玻璃破裂探测器标准.优化减少和检测假警报的功能

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA GB-01-1994

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard details recommended design features to reduce the incidence of false alarms with acoustic glassbreak sensors, or any sensor which uses acoustic glassbreak sensing used in security systems. In addition, specific recommendations are made regarding content in sensor installation instructions and application instructions, also for the purpose of reducing false alarms.Recommendations on design features, installation instructions, and application instructions for maximizing lass break detection are also included. Since the technology of acoustic glass break detection can involve a trade-off between detection and false alarm immunity, a focus solely on false alarm immunity will compromise glass break detection. Detection therefore has equal emphasis in this standard.This standard recognizes that the majority of false alarms and missed detections for glassbreak sensors are due to application and installation errors, and that widespread instruction on application and installation will have the greatest impact toward minimizing false alarms while maximizing glass break detection.
2.[标准] SIA Point Identification Multiplex Protocol - Security and Life Safety Applications - Addressable Detectors, Annunciators and Other Associated Devices

SIA点识别多路传输协议.安全和生命安全应用.可寻址探测器信号器和其他相关设备

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA PID-01-1995

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard defines the SIA protocol for addressable multiplex, sensor, control and annunciation modules for Security and Life Safety systems. This protocol utilizes two way digital transmission scheme, which can be implemented at low cost over a two wire trunk. The trunk also supplies power to the remote devices.The protocol command set and response data allows highly reliable, error resistant transport of both analog and digital messages with fast response mode for any sensor or device in the alarm condition.Devices may be interfaced to the trunk in any order in a single ended or loop configurations.
3.[标准] Access Control Standard Protocol for the 26-bit Wiegand Reader Interface

26位Wiegand读卡器接口的访问控制标准协议

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA AC-01-1996

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： The specifications in this standard define a commonly used interface between card readers and control panels used in the Access Control, Security, Time and Attendance, and other related industries. The standardization of the interface makes the design of readers and control panels uniform for manufacturers and makes system design and integration systematic for architects, designers, specifiers and users.This standard provides specifications for the electrical elements that define the transfer of data from the reader to the control panel, power requirements/limitations, and control of devices contained on the reader. These elements are used to design functional electrical circuits that connect the reader and the control panel.This standard is for adoption by manufacturers to establish a common interface which provides compatibility and interoperability of readers and control panels and by consultants, specifiers and users setting criteria to achieve uniformity in the technical design criteria, requirements or guidelines of systems.
4.[标准] Audio Verification Standard Protocol for Audio Verification and Two-Way Voice - Monitoring Service Command Set

音频验证音频验证和双向语音监控服务命令集的标准协议

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA AV-01-1997

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： The purpose of this proposed standard is to define a basic set of responses to DTMF signals to control two-way voice, microphones, relays, and integrated home system features.This proposed standard describes command sets for controlling the following functions:two-way voice controlmicrophone zoningrelay control.This proposed standard also suggests a method for using computer-activated DTMF signals to control integrated home system features.
5.[标准] On-Premises RF Products - Technical Report - Terminology for Use in Specifying Product Parameters

内部射频产品.技术报告.用于规定产品参数的术语

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA RF-01-1997

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard defines common parameters and measures associated with on-premises RF equipment used in electronic security systems.The purpose of this standard is to enable accurate comparison of RF products to one another and to enable accurate determination of a product's suitability in a given application.
6.[标准] Digital Communication Standard - Ademco Contact ID Protocol - for Alarm System Communications

数字通信标准.报警系统通信用Ademco触点ID协议

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA DC-05-1999

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard details the specification for the "Ademco® Contact ID" communication format, originally developed by the Ademco Group, a division of the Pittway Corporation.The purpose of this standard is to detail the Contact ID signaling format such that it can be adopted by any manufacturer of digital transmitters or receivers. Documentation and distribution of this communication format is intended to provide an across-the-board compatability of equipment designed to this standard regardless of manufacturer.
7.[标准] Digital Communications Standard - SIA 2000 Protocol for Alarm System Communications

数字通信标准.报警系统通信的SIA 2000协议

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA DC-04-2000

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： The SIA-2000 protocol structures the communication between a control and a central station receiver. The basic form of this communication conveys information such as alarms, alarm cancels, troubles, and restorals. This involves tranfsferring information records from the control to the central station, and receiving acknowledgements from the receiver for each record.To support features such as remote panel programming and alarm verification through audio or video means, the protocol has provisions to extend the communication session. Once extended, the receiver can query the control for information or change the control's configuration. The extended session can also be used for verification. It is at this point, that communication using SIA-2000 ends and the appropriate form of communication for verification begins.
8.[标准] Access Control Guideline - Dye Sublimination Printing Practices for PVC Access Control Cards

访问控制指南.PVC访问控制卡的染料升华印刷规程

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA AC-03-2000

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： This guideline defines recommended practices for dye sublimination printing on cards made with Polyvinyl chloride (PVC), Polyvinyl chloride acetate PVCA, or PVC combined with other materials used in Security, Access Control, Time and Attendance, and other related industries.This report provides specifications for the mechanical elements that make up a PVC card and defines the precautions that are to be used in handling and printing on these cards.This guideline is for adoption by card and printer manufacturers to establish compatibility and interoperability of cards and printers. This guideline is for reference by consultants, specifiers and users to aid in the selection and use of this evolving technology.
9.[标准] Digital Communications Standard - Receiver-to-Computer Interface Protocol (Type 2) - for Central Station Equipment Communications

数字通信标准.中央站设备通信用接收器到计算机接口协议（类型2）

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA DC-07-2001

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard describes an interface format for communications between alarm signal receivers and automation computers. This standard is intended for use by equipment in security industry alarm monitoring centers, with possible uses in the areas of energy control and facilities monitoring and management.This standard provides a common interface format for across-the -board compatibility of equipment, regardless of manufacturer, and provides for all the known communication needs between the computer and receiver.This standard defines basic "codes" to identify commonly used dialer protocols used in alarm signal transmitters, as well as conditions in the central station equipment that require a technician or other manual attention.
10.[标准] Architectural Graphics Standard - CAD Symbols for Security System Layout - Release 3.0

建筑制图标准.安全系统布局用CAD符号.第3.0版

发布单位：
美国-安全行业协会(US-SIA)

标准状态：
现行

标准号：
SIA AG-01-2015

发布时间：

中标分类：
-

国标分类：
-

实施时间：

摘要： This standard details a Computer Aided Drafting (CAD) symbol library for security system layout. This set provides standardized, easily recognizable icons representing the form or function of the device and a reduced number of symbols through the development of generic icons with single-character attributes for the mount style and technology or device type.This standard was based on the American Society for Testing and Materials (ASTM) F967 Standard Practice for Security Engineer Symbols (manually drafted symbols) and subsequently updated to include symbols required for security system design and implementation.This standard is intended to provide uniformity in the design and layout of physical security systems, making CAD-generated construction drawings more easily read and understood by all in security management, design disciplines and construction trades.This standard is intended for implementation by architects, building contractors, system integrators, electrical contractors and security managers who use CAD to produce construction drawings, shop drawings and installation/as-built drawings, as well as all other entities that are involved with physical security system layouts. It is meant to serve as a model for elaboration and incorporation into computer products used either for security systems design and layout or other geographical displays of security systems.This standard is cosponsored by SIA and the International Association of Professional Security Consultants (IAPSC).