涂料涂覆设备_国内外标准网文献检索下载

1.[标准] Standard Terminology for Paint Roller Application Tools

涂料滚筒应用工具的标准术语

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D7802-12(2024)

发布时间：
2024-02-01

中标分类：
-

国标分类：
01.040.87 词汇 - 涂料和颜料工业 (词汇)

87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This standard establishes the definitions or terminology used in the manufacturing and testing of paint rollers.1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2.[标准] Standard Practice for Physical Characterization of Paint Brushes

油漆刷物理特性的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D5301-92(2024)

发布时间：
2024-02-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This practice covers the dimensions, terminology, materials and characteristics generally considered of importance to those within, or dealing with paint brushes, and describes methods of determining these parameters. This practice is not meant to be a definitive analytical method to deformulate brushes.1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1It is important to recognize that a brush can be a mixture of several chemically different filaments or bristles, or both, in several cross sections, thicknesses and lengths. The following procedures will be helpful in identifying brush composition.
3.[标准] 滚筒刷质量分级

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/CIQA 45-2023

发布时间：
2023-01-13

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：
2023-01-13

摘要：范围:本文件规定了滚筒刷的一般要求，测试环境及准备要求，分级、试验方法和评价。本文件适用于生产、验收、测试、评价滚筒刷;主要技术内容:首先明确标准的适用范围：本标准主要为了便利滚筒刷产品出口贸易，关注于产品质量及其质量分级，本标准规定了滚筒刷的一般要求、分级与评价。本标准第3章给出了本文件中需要用到的术语和定义，共定义了滚筒刷等17项术语和定义。本标准第4章给出了滚筒刷的一般要求，包括原材料要求、产品外观要求。本标准第5章给出了滚筒刷的测试环境及准备要求。本标准第6章给出了依据多项指标要求划分的A、B、C三个质量等级的质量等级划分表，以及评价确定滚筒刷质量等级的规定
4.[标准] 油漆刷质量分级评价技术规范

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/CAB 0165-2022

发布时间：
2022-08-24

中标分类：
Y 轻工、文化与生活用品

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：
2022-08-24

摘要：范围:本标准规范了油漆刷的一般要求、分级与评价。本标准适用于油漆刷的质量等级评价;主要技术内容:本标准规范了油漆刷的一般要求、分级与评价。本标准适用于油漆刷的质量等级评价
5.[标准] Standard Test Method for Filling Material Shedding of Paint Brushes

油漆刷填充材料脱落的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D7834-13(2019)

发布时间：
2019-10-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This test method describes the procedure for testing the shedding properties of both natural bristle and synthetic filament paint brushes (referred as filling material).1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
6.[标准] Standard Practice for Preparation of Paint Brushes for Evaluation

评定用油漆刷制备的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D5068-04(2019)

发布时间：
2019-10-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This practice describes the preparation of paint brushes for evaluation.1.2This practice is applicable to paint brushes 50 to 100 mm (2 to 4 in.) in width.1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1Until the paint brush is fully conditioned and wetted with paint, only part of the paint loaded onto the brush can be transferred to the surface being painted. By properly preparing the brush before use, the amount of paint delivered to the surface can be made more uniform and reflect real use.
7.[标准] Standard Practice for Preparation of Paint-Roller Covers for Evaluation of Architectural Coatings

建筑涂料评定用漆辊盖的制备

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D5069/D5069M-13(2019)

发布时间：
2019-10-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This practice covers the preparation or breaking-in of paint-roller covers for evaluation.1.2This practice is applicable to paint-roller covers having nap lengths up to 13 mm [1/2in.]. Longer pile rollers can be adapted.1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1Until a paint-roller cover is saturated with paint, only part of the paint loaded onto the paint-roller cover can be transferred to a surface being painted. The remainder of the paint is absorbed into the fabric of the paint-roller cover. The amount of paint absorbed by a paint-roller cover is inversely proportional to the amount already present within the paint-roller cover. By saturating the paint-roller cover before testing, quantitative inaccuracies of the amount of paint delivered to a surface are eliminated.4.1.1Using a saturated paint-roller cover enables the user to apply paint at controllable spreading rates.4.1.2Using a saturated paint-roller cover affords reproducibility, when repeating a test.
8.[标准] Standard Test Method for Evaluation of Cleanability of Paint Brushes

评定油漆刷清洁性的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D5913-96(2019)

发布时间：
2019-10-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This test method covers a laboratory procedure for the evaluation or comparison of the cleanability of paint brushes, or both, when used with latex paints.1.2This test method is applicable to paint brushes up to 100 mm (4 in.) in width and of similar head dimensions as described in PracticeD5301.1.3The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1The final appearance of a paint brush after it has been used and cleaned is related to the ability of the brush to perform consistently upon repeated use. This test method offers a subjective visual criteria that provides a rank order of cleanability of the filaments of a brush after use.
9.[标准] Standard Specification for Cautionary Labeling of Extension Poles For Use With Paint Applicators Distributed In North America

用于北美分布的涂漆机的延长杆警示标签标准规范

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D7054-04(2019)

发布时间：
2019-10-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This specification covers generally recognized requirements for the cautionary labeling to be placed on extension poles manufactured or sold, or both, for the use with paint preparation and application tools. This specification does not address any other labeling, construction, or safety requirements.1.2The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
10.[标准] Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:2017)

用于无空气喷涂的橡胶和/或塑料软管和软管组件 - 规格（ISO/DIS 8028:2016）

发布单位：
国际组织-欧洲标准化委员会(IX-CEN)

标准状态：
现行

标准号：
EN ISO 8028:2018

发布时间：
2018-01-31

中标分类：
G42 化工 - 橡胶制品及其辅助材料 - 胶管、胶带、胶布

国标分类：
23.040.70 管道部件和管道 - 软管和软管组件

87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：
2018-01-31

摘要： ISO 8028:2017 specifies the requirements for four types of hose and hose assemblies for use in airless paint spraying. The four types are differentiated by burst pressure and operating temperature, and can be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
11.[标准] Spray booths for organic coating material - Safety requirements

有机涂料喷涂室 - 安全要求

发布单位：
国际组织-欧洲标准化委员会(IX-CEN)

标准状态：
现行

标准号：
EN 16985:2018

发布时间：
2018-12-05

中标分类：
A20/39 综合 - 基础标准

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：
2018-12-05

摘要： This European Standard deals with all significant hazards, hazardous situations and hazardous events relevant to spray booths for the application of organic liquid and powder coating materials, when they are used as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse.See Annex A for significant hazards.Interfaces between spray booths and other machinery used in coating application are given in Figure 1.The specific significant risks related to the use of this machinery with foodstuff and pharmaceutical products are not dealt with in this standard.The specific significant risks related to drying operation of combined spraying and drying booths are not dealt with in this standard, but in EN 1539:2015.This European Standard is not applicable to:-spaces for application of organic coating material consisting only of an extraction wall;-platforms attached to spray booths (e.g. for touch-up jobs);-flock booths (see EN 50223:2015);-spray booths with airflow from vertical inlet to horizontal extraction or from horizontal inlet to vertical extraction.This European Standard is not applicable to machinery manufactured before the date of its publication as European Standard.
12.[标准] Standard Practice for Measuring Curl in Paint Brush Filling Material

油漆刷填充材料卷曲测量标准实践

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6957-12(2018)

发布时间：
2018-09-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This practice describes the procedure for measuring curl in synthetic filament.1.2This practice is applicable to filament 2 to 5 in. (50.8 to 127 mm) in length.1.3This practice is applicable to tapered filament or level filament.1.4This practice is applicable to loose filling material and material removed from a brush.1.5The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1It is important for the manufacturing and performance of a brush to have filaments with minimal curl.
13.[标准] 精密涂布生产线

发布单位：
中国-广东省地方标准(CN-DB44)

标准状态：
作废

标准号：
DB44/T 2044-2017

发布时间：
2017-08-28

中标分类：
Y99 轻工、文化与生活用品 - 轻工机械 - 其他轻工机械

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：
2017-11-28

摘要：本标准规定了精密涂布生产线的术语和定义、型号、型式与基本参数、技术要求、试验方法、检验规则、标志、包装、运输和贮存一般原则；本标准适用于对基材表面进行功能性涂层加工的精密涂布生产线（简称生产线），其中适用的基材包括纸张、塑料薄膜、金属箔、布等。本标准适用于热风干燥的精密涂布生产线
14.[标准] Standard Test Method for Bulk Density of Level Paintbrush Filaments

水平画笔长丝的体积密度的标准测试方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D5959-12(2017)

发布时间：
2017-06-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This test method covers a procedure for measuring the weight of filaments per unit volume.1.2This test method is applicable only to monofilament with consistent longitudinal (level) profiles.1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1Filaments are available in a variety of cross sections and materials. A measure of bulk density permits the brushmaker to estimate the weight of filament required to prepare a given number of brushes.
15.[标准] Standard Test Method for Bulk Density of Tapered Paintbrush Filaments

锥形油漆刷长丝的体积密度的标准测试方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6737-12(2017)

发布时间：
2017-06-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This test method covers a procedure for measuring the weight of filaments per unit volume.1.2This method is applicable only to monofilament with tapered longitudinal profiles.1.3The values given in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1Filaments are available in a variety of cross-sections and materials. A measure of bulk density permits the brushmaker to estimate the weight of filament required to prepare a given number of brushes.
16.[标准] Standard Test Method for Testing Fracture of Level Paintbrush Filaments

用于测试水平画笔长丝断裂的标准测试方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D7233-08(2017)

发布时间：
2017-06-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This test method covers a procedure for determining the number of fractures present when paintbrush filaments are bent.1.2This method is applicable only to monofilaments with consistent longitudinal cross sectional dimensions commonly referred to as “level” filaments.1.3The values derived are in percent fractured filaments. For example, 2 fractured out of 18 filaments tested =2/18or 11 %.1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1This method is intended to evaluate filaments for suitability of use in paintbrushes prior to manufacture. Filament fracture resistance is very important because paintbrushes are bent or flexed during painting and it is necessary that the filaments are not permanently deformed with usage.
17.[标准] Standard Terminology for Paint Brush Application Tools

油漆刷应用工具的标准术语

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D7801-17

发布时间：
2017-06-01

中标分类：
-

国标分类：
01.040.87 词汇 - 涂料和颜料工业 (词汇)

87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This standard establishes the definitions for terminology used in testing and manufacturing of paint brushes.1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
18.[标准] Standard Test Method for Fiber Shedding of Paint Roller Covers

油漆滚筒盖纤维脱落标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D7804-12(2017)

发布时间：
2017-06-01

中标分类：
-

国标分类：
87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： 1.1This test method describes a procedure for determining the amount of releasable fibers transferred from a paint roller cover to a surface being painted.1.2This test method is applicable to pile fabric paint roller covers.1.3Because both the application and panel evaluation are subjective, this test method should be used only for comparative testing within one facility using one operator for each set of applications, as the end result assigned by different facilities may not agree.1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Hazards.1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1fibers that are released during painting can lead to a finish that is aesthetically unacceptable.
19.[标准] Rubber and/or plastics hoses and hose assemblies for airless paint spraying — Specification

橡胶和/或塑料软管和软管组件用于无气喷涂 - 规格

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 8028:2017

发布时间：
2017-12-05

中标分类：
-

国标分类：
83.140.40 橡胶和塑料制品 - 软管

87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：

摘要： ISO 8028:2017 specifies the requirements for four types of hose and hose assemblies for use in airless paint spraying. The four types are differentiated by burst pressure and operating temperature, and can be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
20.[标准] Paints and varnishes - Standard panels for testing (ISO 1514:2016)

油漆和清漆 - 测试标准面板（ISO 1514:2016）

发布单位：
国际组织-欧洲标准化委员会(IX-CEN)

标准状态：
现行

标准号：
EN ISO 1514:2016

发布时间：
2016-08-17

中标分类：
P50 土木、建筑 - 城乡规划与市政工程 - 城乡规划

国标分类：
87.040 涂料和颜料工业 - 涂料和清漆

87.100 涂料和颜料工业 - 涂料涂覆设备

实施时间：
2016-08-17

摘要： ISO 1514:2016 specifies several types of standard panels and describes procedures for their preparation prior to painting. These standard panels are for use in general methods of test for paints, varnishes and related products.