燃料_国内外标准网文献检索下载

1.[标准] 车用乙醇汽油快速筛查技术规范

发布单位：
中国-安徽省地方标准(CN-DB34)

标准状态：
现行

标准号：
DB34/T 4693-2024

发布时间：
2024-01-11

中标分类：
E31 石油 - 石油产品 - 燃料油

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2024-02-11
2.[标准] 车用柴油快速筛查技术规范

发布单位：
中国-安徽省地方标准(CN-DB34)

标准状态：
现行

标准号：
DB34/T 4692-2024

发布时间：
2024-01-11

中标分类：
E31 石油 - 石油产品 - 燃料油

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2024-02-11
3.[标准] 轻质石油馏分和产品中烃族组成和苯含量的测定　多维气相色谱法

发布单位：
中国-国家标准(CN-GB)

标准状态：
即将实施

标准号：
GB/T 30519-2024

发布时间：
2024-09-29

中标分类：
E31 燃料油

国标分类：
75.160.20 液体燃料

实施时间：
2025-04-01

摘要：本文件描述了用多维气相色谱技术测定轻质石油馏分和产品中烯烃、芳烃等烃族组成和苯含量的试验方法。
本文件适用于终馏点不高于215 ℃的轻质石油馏分和产品（如汽油、汽油调合组分、溶剂油等）中烯烃、芳烃等烃族组成和苯含量的测定。测定浓度范围烯烃体积分数为0.5%～70%（质量分数为0.4%～64%），芳烃体积分数为1%～80%（质量分数为1.2%～92%），苯体积分数为0.2%～10%（质量分数为0.2%～12%）。测量含量超出上述范围的样品时，精密度尚未确定。
本文件也适用于终馏点不高于215 ℃、由其他非常规原油如页岩或油砂加工得到的汽油产品或由非石油矿物燃料合成加工的烃类燃料如费托合成油等，但尚未确定精密度。

获取标准
4.[标准] 木炭

发布单位：
中国-国家标准(CN-GB)

标准状态：
即将实施

标准号：
GB/T 17664-2024

发布时间：
2024-09-29

中标分类：
B73 木炭

国标分类：
75.160 燃料

实施时间：
2025-04-01

摘要：本文件规定了木炭的技术要求，描述了相应的试验方法，并规定了检验规则、标志、包装、运输、贮存等要求。
本文件适用于以木材、竹材、秸秆等生物质原料经炭化而制成的木炭的生产、贸易或流通。

获取标准
5.[标准] 焦炭溶损率及溶损后强度试验方法

发布单位：
中国-国家标准(CN-GB)

标准状态：
现行

标准号：
GB/T 44037-2024

发布时间：
2024-05-28

中标分类：
H32 焦炭

国标分类：
75.160.10 固体燃料

实施时间：
2024-12-01

摘要：本文件描述了测定焦炭溶损率及溶损后强度的原理、试验仪器、设备和材料、试样的采取和制备、试验步骤、结果计算及精密度的试验方法。
本文件适用于高炉炼铁用冶金焦炭溶损率及溶损后强度的测定，其他焦炭参照执行。

获取标准
6.[标准] Standard Test Method for Cetane Number of Diesel Fuel Oil

柴油十六烷值的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D613-24

发布时间：
2024-02-01

中标分类：
-

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：

摘要： 1.1This test method covers the determination of the rating of diesel fuel oil in terms of an arbitrary scale of cetane numbers using a standard single cylinder, four-stroke cycle, variable compression ratio, indirect injected diesel engine.1.2The cetane number scale covers the range from zero (0) to 100, but typical testing is in the range of 30 to 65 cetane number.1.3The values for operating conditions are stated in SI units and are to be regarded as the standard. The values given in parentheses are the historical inch-pound units for information only. In addition, the engine measurements continue to be in inch-pound units because of the extensive and expensive tooling that has been created for these units.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.For more specific warning statements, seeAnnex A1.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1The cetane number provides a measure of the ignition characteristics of diesel fuel oil in compression ignition engines.5.2This test method is used by engine manufacturers, petroleum refiners and marketers, and in commerce as a primary specification measurement related to matching of fuels and engines.5.3Cetane number is determined at constant speed in a precombustion chamber type compression ignition test engine. The relationship of test engine performance to full scale, variable speed, variable load engines is not completely understood.5.4This test method may be used for unconventional fuels such as synthetics, vegetable oils, and the like. However, the relationship to the performance of such materials in full scale engines is not completely understood.
7.[标准] Standard Specification for Leaded Aviation Gasolines

含铅航空汽油标准规范

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D910-24

发布时间：
2024-03-01

中标分类：
-

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：

摘要： 1.1This specification covers formulating specifications for purchases of aviation gasoline under contract and is intended primarily for use by purchasing agencies.1.2This specification defines specific types of aviation gasolines for civil use. It does not include all gasolines satisfactory for reciprocating aviation engines. Certain equipment or conditions of use may permit a wider, or require a narrower, range of characteristics than is shown by this specification.1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
8.[标准] Standard Test Method for Water Reaction of Aviation Fuels

航空燃料水反应的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D1094-24

发布时间：
2024-03-01

中标分类：
-

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：

摘要： 1.1This test method covers the determination of the presence of water-miscible components in aviation gasoline and turbine fuels, and the effect of these components on volume change and on the fuel-water interface.1.2The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.This standard involves the use of hazardous chemicals identified in Section7. Before using this standard, refer to suppliers' safety labels, Material Safety Data Sheets and other technical literature.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1When applied to aviation gasoline, water reaction volume change using the technique reveals the presence of water-soluble components such as alcohols. When applied to aviation turbine fuels, water reaction interface rating using the technique is not reliable in revealing the presence of surfactants which disarm filter-separators quickly and allow free water and particulates to pass; but can reveal the presence of other types of contaminants. Other tests, such as Test MethodD3948, are capable of detecting surfactants in aviation fuels.
9.[标准] Standard Test Method for Phosphorus in Gasoline

汽油中磷含量的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D3231-24

发布时间：
2024-03-01

中标分类：
-

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：

摘要： 1.1This test method covers the determination of phosphorus generally present as pentavalent phosphate esters or salts, or both, in gasoline. This test method is applicable for the determination of phosphorus in the range from 0.2 mg to 40 mg P/L or 0.0008 g to 0.15 g P/U.S. gal.1.2The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.For specific warning statements, see Section7and10.5.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1Phosphorus in gasoline will damage catalytic convertors used in automotive emission control systems, and its level therefore is kept low.
10.[标准] Standard Terminology of Coal and Coke

煤和焦炭的标准术语

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D121-15(2024)

发布时间：
2024-03-01

中标分类：
-

国标分类：
01.040.73 词汇 - 采矿和矿产品 (词汇)

01.040.75 词汇 - 石油及相关技术 (词汇)

73.040 采矿和矿产品 - 煤

75.160.10 燃料 - 固体燃料

实施时间：

摘要： 1.1This terminology defines the technical terms used in standards that are the responsibility of Committee D05 on Coal and Coke. The terms are used in:1.1.1The sampling of coal and coke under conditions required for most commercial and technical purposes related to coal and coke.1.1.2Bias and related statistical testing,1.1.3The description of coal, both visually in the field and microscopically in the laboratory,1.1.4Chemical and physical analyses of coal and coke,1.1.5Classification of coal, and1.1.6Certain other related practices and guides applicable to the coal and coke industries.1.2This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
11.[标准] Standard Test Method for Smoke Point of Kerosene and Aviation Turbine Fuel

煤油和航空涡轮燃料烟点的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D1322-24

发布时间：
2024-03-01

中标分类：
-

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：

摘要： 1.1This test method covers two procedures for determination of the smoke point of kerosene and aviation turbine fuel, a manual procedure and an automated procedure, which give results with different precision.1.2The automated procedure is the referee procedure.1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1This test method provides an indication of the relative smoke producing properties of kerosenes and aviation turbine fuels in a diffusion flame. The smoke point is related to the hydrocarbon type composition of such fuels. Generally the more aromatic the fuel the smokier the flame. A high smoke point indicates a fuel of low smoke producing tendency.5.2The smoke point is quantitatively related to the potential radiant heat transfer from the combustion products of the fuel. Because radiant heat transfer exerts a strong influence on the metal temperature of combustor liners and other hot section parts of gas turbines, the smoke point provides a basis for correlation of fuel characteristics with the life of these components.
12.[标准] 船用残渣燃料油中酚类和脂肪酸甲酯类化合物的测定气相色谱-质谱/质谱法

发布单位：
中国-行业标准-商品检验(CN-SN)

标准状态：
现行

标准号：
SN/T 5564-2023

发布时间：
2023-05-05

中标分类：
E31 石油 - 石油产品 - 燃料油

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2023-12-01
13.[标准] 柴油清净增效剂应用技术要求

发布单位：
中国-山东省地方标准(CN-DB37)

标准状态：
现行

标准号：
DB37/T 4594-2023

发布时间：
2023-03-29

中标分类：
E61 石油 - 石油产品添加剂 - 添加剂

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2023-04-29
14.[标准] 成品油质量追溯体系建设规范

发布单位：
中国-山东省地方标准(CN-DB37)

标准状态：
现行

标准号：
DB3705/T 24-2023

发布时间：
2023-12-15

中标分类：
E30 石油 - 石油产品 - 石油产品综合

国标分类：
75.160.01 燃料 - 燃料综合

实施时间：
2024-01-15
15.[标准] 四川省成品油快速筛查技术规范

发布单位：
中国-四川省地方标准(CN-DB51)

标准状态：
现行

标准号：
DB51/T 3054-2023

发布时间：
2023-04-28

中标分类：
E31 石油 - 石油产品 - 燃料油

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2023-06-01

摘要：本文件规定了车用汽油和车用柴油快速筛查的术语和定义、要求和试验方法、取样、方法验证、载具（车辆）要求及结果处理和报告等内容。本文件适用于四川省内生产、储运、销售和使用环节等成品油产品的快速筛查，不适用于对成品油产品质量的判定
16.[标准] 醇基燃料使用安全规范

发布单位：
中国-河北省地方标准(CN-DB13)

标准状态：
现行

标准号：
DB13/T 5742-2023

发布时间：
2023-07-28

中标分类：
E31 石油 - 石油产品 - 燃料油

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2023-08-28
17.[标准] 液化石油气气瓶追溯技术规范

发布单位：
中国-河南省地方标准(CN-DB41)

标准状态：
现行

标准号：
DB4114/T 185-2023

发布时间：
2023-06-28

中标分类：
C78 医药、卫生、劳动保护 - 劳动保护管理 - 安全卫生管理

国标分类：
75.160.30 燃料 - 气体燃料

实施时间：
2023-07-28

摘要：商丘市
18.[标准] 车用乙醇汽油（E10）快速筛检技术规范

发布单位：
中国-吉林省地方标准(CN-DB22)

标准状态：
现行

标准号：
DB22/T 3622-2023

发布时间：
2023-12-28

中标分类：
E31 石油 - 石油产品 - 燃料油

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2024-02-01
19.[标准] 柴油发动机氮氧化物还原剂尿素水溶液（AUS 32）快速筛检技术规范

发布单位：
中国-吉林省地方标准(CN-DB22)

标准状态：
现行

标准号：
DB22/T 3620-2023

发布时间：
2023-12-28

中标分类：
E31 石油 - 石油产品 - 燃料油

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2024-02-01
20.[标准] 车用柴油快速筛检技术规范

发布单位：
中国-吉林省地方标准(CN-DB22)

标准状态：
现行

标准号：
DB22/T 3621-2023

发布时间：
2023-12-28

中标分类：
E31 石油 - 石油产品 - 燃料油

国标分类：
75.160.20 燃料 - 液体燃料

实施时间：
2024-02-01