石蜡、沥青材料和其他石油产品_国内外标准网文献检索下载

1.[标准] 环保净味沥青通用技术规范

发布单位：
中国-江苏省地方标准(CN-DB32)

标准状态：
现行

标准号：
DB32/T 4650-2024

发布时间：
2024-01-09

中标分类：
E43 石油 - 石油产品 - 石油沥青

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2024-02-09
2.[标准] 石油沥青性能等级评价试验方法

发布单位：
中国-国家标准(CN-GB)

标准状态：
即将实施

标准号：
GB/T 44357-2024

发布时间：
2024-08-23

中标分类：
E43 石油沥青

国标分类：
75.140 石蜡、沥青材料和其他石油产品

实施时间：
2025-03-01

摘要：本文件界定了石油沥青性能等级评价试验方法相关的术语和定义，描述了石油沥青性能等级评价试验条件、取样、试样准备、试验方法及试验结果评定。
本文件适用于不同用途的固体或半固体石油沥青结合料，也适合于液体沥青和乳化沥青的残留物。

获取标准
3.[标准] Standard Test Method for Toughness and Tenacity of Asphalt Materials

沥青材料韧性和韧性的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D5801-24

发布时间：
2024-01-15

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

91.100.50 建筑材料 - 粘合料、密封材料

实施时间：

摘要： 1.1This test method describes the procedure for measuring the toughness and tenacity of asphalt materials. Typically, the test method has been used to characterize elastomer-modified asphalts, although values for toughness and tenacity may be obtained for any type of polymer-modified or non-modified asphalt.1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.2.1Exception—Sample mass is given only in SI units. Sample mass as given in SI units should be regarded as standard. No other units of sample mass are included in this standard.1.3Warning—Mercury has been designated by the United States Environmental Protection Agency and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable Material Safety Data Sheet (MSDS) for details and EPA’s website—http://www.epa.gov/mercury/index.htm—for additional information. Users should be aware that selling mercury and/or mercury-containing products in your state may be prohibited by state law.1.4The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1This test method is useful in confirming that an asphalt cement has been modified with a material that provides a significant elastomeric component. Elastomer-modified asphalts can be characterized by their ability to be stretched to a large elongation while at the same time resisting further stretching. Toughness and tenacity are two parameters for measuring this ability.Note 1:The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of SpecificationD3666are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with SpecificationD3666alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of SpecificationD3666or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
4.[标准] 沥青混合料改性添加剂第8部分：高模量剂

发布单位：
中国-行业标准-交通(CN-JT)

标准状态：
现行

标准号：
JT/T 860.8-2023

发布时间：
2023-01-19

中标分类：
P66 土木、建筑 - 交通运输工程 - 公路工程

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

93.080.20 道路工程 - 道路建筑材料

实施时间：
2023-04-19

摘要：本部分适用于沥青混合料改性添加剂高模量剂的生产、检验和使用
5.[标准] 石油蜡熔点的测定冷却曲线法

发布单位：
中国-国家标准(CN-GB)

标准状态：
现行

标准号：
GB/T 2539-2023

发布时间：
2023-09-07

中标分类：
E42 石油 - 石油产品 - 石油蜡

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2024-04-01

摘要：本文件描述了冷却曲线法测定石油蜡熔点的方法。本文件适用于常温下固体石油蜡熔点的测定，不适用于石油脂、微晶蜡，以及石油脂、微晶蜡与石蜡或粗石蜡的混合物熔点的测定。

获取标准
6.[标准] 石油蜡和石油脂滴熔点测定法

发布单位：
中国-国家标准(CN-GB)

标准状态：
现行

标准号：
GB/T 8026-2023

发布时间：
2023-09-07

中标分类：
E42 石油 - 石油产品 - 石油蜡

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2024-04-01

摘要：本文件描述了石油蜡和石油脂滴熔点的测定方法。
本文件中方法A适用于石油蜡和石油脂滴熔点的测定。
本文件中方法B适用于石油蜡和石油脂生产过程滴熔点的测定，不适用于合成蜡、动物蜡和植物蜡与石油蜡的调和蜡滴熔点的测定。

获取标准
7.[标准] 全精炼石蜡

发布单位：
中国-国家标准(CN-GB)

标准状态：
现行

标准号：
GB/T 446-2023

发布时间：
2023-09-07

中标分类：
E42 石油 - 石油产品 - 石油蜡

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2024-04-01

摘要：本文件规定了全精炼石蜡的产品分类，技术要求和试验方法，取样和组批，标志、包装、运输、贮存及交货验收。本文件适用于以石油馏分为原料，经物理分离和深度精制等方法所得到的，用于工艺蜡烛、电子行业、航空航天、建筑建材、电力行业、精密铸造、涂料等领域的石蜡。

获取标准
8.[标准] 锂离子电池负极材料用沥青

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/CPCIF 0251-2023

发布时间：
2023-06-01

中标分类：
E 石油

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2023-09-01

摘要：范围:本文件规定了锂离子电池负极材料用沥青的产品分类、技术要求、试验方法、检测规则、包装、贮存、运输和质量证明。本文件适用于以煤沥青、含芳香烃石油类重质油为原料，经适当工艺生产得到的沥青产品。该产品主要用于锂离子电池负极材料的原料，还可用于冷捣糊、镁碳砖、三高石墨用粘结剂沥青;主要技术内容:本文件规定了锂离子电池负极材料用沥青的产品分类、技术要求、试验方法、检测规则、包装、贮存、运输和质量证明。本文件适用于以煤沥青、含芳香烃石油类重质油为原料，经适当工艺生产得到的沥青产品。该产品主要用于锂离子电池负极材料的原料，还可用于冷捣糊、镁碳砖、三高石墨用粘结剂沥青
9.[标准] SBS改性沥青生产技术规范

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/QGCML 1146-2023

发布时间：
2023-08-05

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2023-08-20

摘要：主要技术内容:本文件规定了SBS改性沥青生产技术规范的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存、检验报告、交货验收。本文件适用于SBS改性沥青的生产及检验
10.[标准] 低碳型SBS改性沥青混合料应用技术规程

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/SDASTC 007-2023

发布时间：
2023-10-30

中标分类：
E43 石油 - 石油产品 - 石油沥青

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2023-11-07

摘要：主要技术内容:本文件规定了低碳型SBS改性沥青混合料的原材料、性能要求、施工工艺、质量管理和检查验收。本文件适用于SBS改性沥青路面工程
11.[标准] 沥青混合料

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/CIPR 023-2023

发布时间：
2023-02-27

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2023-03-17

摘要：主要技术内容:本文件规定了沥清混合料的技术要求、试验方法、检验规则和运输。本文件适用于路面铺设的沥青混合物及其制备方法
12.[标准] 彩色沥青生产技术规范

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/QGCML 1147-2023

发布时间：
2023-08-05

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2023-08-20

摘要：主要技术内容:本文件规定了彩色沥青生产技术规范的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存、检验报告、交货验收。本文件适用于彩色沥青的生产及检验
13.[标准] 石油化工产品储运挥发性有机物冷凝回收液

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/CASME 628-2023

发布时间：
2023-08-18

中标分类：
E 石油

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2023-08-30

摘要：范围:本文件适用于石油化工产品储运过程中产生的挥发性有机物经冷凝回收后，资源化定向利用的C3～C12混合液体;主要技术内容:本文件规定了石油化工产品储运挥发性有机物冷凝回收液的技术要求、试验方法、检验规则、标志、包装、运输、贮存和安全
14.[标准] 环保沥青混合料

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/CIPR 022-2023

发布时间：
2023-02-28

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2023-03-07

摘要：主要技术内容:本文件规定了环保沥青混合料的技术要求、试验方法、检验规则和运输。本文件适用于路面铺设的沥青混合物及其制备方法
15.[标准] 通用型碳纤维可纺沥青

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/QGCML 1766-2023

发布时间：
2023-10-19

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：
2023-11-03

摘要：主要技术内容:本文件规定了通用型碳纤维可纺沥青的术语定义、产品分类、技术要求、试验方法、检验规则、标志、包装、运输及贮存、安全注意事项。本文件适用于以含芳香烃石油类重质油、煤沥青为原料，经适当工艺生产后得到的沥青产品，主要用于碳纤维的原料，还可用于其他工业产品的包覆或粘结剂沥青
16.[标准] Standard Practice for Infrared (IR) Procedure for Determination of Aromatic/ Aliphatic Ratio of Bituminous Emulsions

沥青乳液芳香/脂肪族比测定的红外（IR）程序的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6805-02(2023)

发布时间：
2023-01-01

中标分类：
-

国标分类：
71.080.10 有机化学 - 脂族烃

71.080.15 有机化学 - 芳香烃

75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：

摘要： 1.1This practice uses infrared analytical techniques to qualitatively determine in the laboratory a ratio of aromatic absorbance to aliphatic absorbance. This practice may be used to determine if the bitumen in the emulsion is predominantly aromatic or aliphatic in nature.1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1The results of this practice may be used to distinguish tar-based emulsion from an asphalt-based emulsion for specification compliance purposes.
17.[标准] Standard Test Method for Needle Penetration of Petroleum Waxes

石油蜡针入度的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D1321-23

发布时间：
2023-12-01

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：

摘要： 1.1This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle. This test method is applicable to waxes having a penetration of not greater than 250.Note 1:This test method is similar to the needle method for determining the penetration of bituminous material, Test MethodD5. Cone methods applicable to greases and to petrolatum are described in Test MethodsD217and Test MethodD937, respectively.1.2WARNING—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.1.3The values stated in SI units are to be regarded as the standard.1.3.1Exception—The values given in parentheses are for information only.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1Petroleum waxes differ in hardness. Needle penetration is a measurement of hardness. Hardness may have a significant effect upon other physical properties.
18.[标准] Standard Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent UV, Water Spray, and Condensation Method)

沥青材料加速老化试验条件和程序的标准实施规程（荧光紫外、喷水和冷凝法）

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D4799/D4799M-17(2023)

发布时间：
2023-02-01

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

91.100.50 建筑材料 - 粘合料、密封材料

93.080.20 道路工程 - 道路建筑材料

实施时间：

摘要： 1.1This practice describes test conditions and procedures for fluorescent UV and condensation exposures conducted according to PracticesG151andG154for bituminous roofing and waterproofing materials. (See TerminologyG113.)1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1This weathering apparatus is used for comparing the weathering characteristics of bituminous materials against a control material for which the outdoor weathering characteristics are known. It is not possible to establish a precise correlation between accelerated and natural weathering because (1) there are geographical climatic variations, local weather variations, and variations in local pollutants, and (2) the relation between accelerated and natural weathering is material dependent. Acceleration factors differ between materials as well as between formulations of the same material. GuideG141provides guidance regarding this issue.Note 1:This practice can be used for other than bituminous materials, but the significance and use have not been evaluated.
19.[标准] Standard Test Method for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method

用自动真空密封法测定压实沥青混合料的体积比重和密度的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6752/D6752M-23

发布时间：
2023-11-01

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：

摘要： 1.1This test method covers the determination of bulk specific gravity of compacted asphalt mixtures by the vacuum sealing method.1.2This method can be used for compacted cylindrical and cubical laboratory and field asphalt mixture specimens.1.3The bulk specific gravity of the compacted asphalt mixtures may be used in calculating the unit weight of the mixture.1.4The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.5The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1The results obtained from this method can be used to determine the unit weight of compacted asphalt mixtures, and in conjunction with Test MethodD3203/D3203M, to obtain percent air voids. These values in turn may be used in determining the relative degree of compaction.4.2Since specific gravity has no units, it must be converted to density in order to do calculations that require units. This conversion is made by multiplying the specific gravity at a given temperature by the density of water at the same temperature.4.3This method can be used for 100 mm [4 in.] and 150 mm [6 in.] diameter cylindrical as well as cubical asphalt mixture specimens to correct for inconsistencies in sample weight determinations resulting from drainage of water from samples and inaccuracy in saturated surface dry weight of absorptive coarse and open-graded mixes. Asphalt mixes such as stone matrix asphalt (SMA), porous friction course, and coarse-graded mixes with significant surface texture and interconnected voids can be tested with this method. Follow manufacturer recommendation for appropriate bag sizes to be utilized with cubical and abnormally shaped samples.4Note 1:The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of SpecificationD3666are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with SpecificationD3666alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of SpecificationD3666or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
20.[标准] Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

蒸馏法测定石油产品和沥青材料中水含量的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D95-23

发布时间：
2023-10-01

中标分类：
-

国标分类：
75.140 石油及相关技术 - 石蜡、沥青材料和其他石油产品

实施时间：

摘要： 1.1This test method covers the determination of water in the range from 0 % to 25 % by volume in petroleum products, tars, and other bituminous materials by the distillation method.Note 1:Volatile water-soluble material, if present, may be measured as water.1.2The specific products considered during the development of this test method are listed in Table 1. For bituminous emulsions refer to Test MethodD244. For crude oils, refer to Test MethodD4006(APIMPMSChapter 10.2).Note 2:With some types of oil, satisfactory results may be obtained from Test MethodD1796(APIMPMSChapter 10.6).1.3The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.For specific hazard statements, see Section6.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1A knowledge of the water content of petroleum products is important in the refining, purchase, sale, and transfer of products.5.2The amount of water as determined by this test method (to the nearest 0.05 % or 0.1 % by volume, depending on the trap size used) may be used to correct the volume involved in the custody transfer of petroleum products and bituminous materials.5.3The allowable amount of water may be specified in contracts.