雾化剂罐_国内外标准网文献检索下载

1.[标准] Standard Guide for Determining Cross-Section Averaged Characteristics of a Spray Using Laser-Diffraction Instruments in a Wind Tunnel Apparatus

在风洞设备中用激光衍射仪测定喷雾横截面平均特性的标准指南

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM E2872-14(2024)

发布时间：
2024-02-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1The purpose of this guide is to define a test procedure for applying the laser diffraction (LD) method to estimate an average droplet size distribution that characterizes the flux of liquid droplets produced by a specified spray generation device under specified gas co-flow conditions using a specified liquid. The intended scope is limited to artificially generated sprays with high speed co-flow. The droplets are assumed to be in the size range of 1 µm to 2000 µm in diameter and occur in sprays that are contained within a volume as small as a few cubic centimetres or as large as a cubic metre. The droplet sizes are assumed to be distributed non-uniformly within the spray volume.1.2This guide is intended primarily to guide measurement of performance of nozzles and atomizers using LD instruments.1.3Non-uniform sprays require measurements across the entire spray cross section or through several chords providing a representative sample of the overall spray cross section. The aim of multiple-chord measurements is to obtain a single droplet size distribution that characterizes the whole spray rather than values from a single chordal measurement.1.4Use of this guide requires that the instrument does not interfere with spray production and does not significantly impinge upon or disturb the co-flow of gas and the spray. This technique is, therefore, considered non-intrusive.1.5The computation of droplet size distributions from the light-scattering distributions is done using Mie scattering theory or Fraunhofer diffraction approximation. The use of Mie theory accounts for light refracted through the droplet and there is a specific requirement for knowledge of both real (refractive) and imaginary (absorptive) components of the complex index of refraction. Mie theory also relies on an assumption of droplet homogeneity. The Fraunhofer diffraction approximation does not account for light refracted through the droplet and does not require knowledge of the index of refraction.1.6The instruments shall include data-processing capabilities to convert the LD scattering intensities into droplet size distribution parameters in accordance with PracticeE799and Test MethodE1260.1.7The spray is visible and accessible to the collimated beam produced by the transmitter optics of the LD instrument. The shape and size of the spray shall be contained within the working distance of the LD system optics as specified by the instrument manufacturer.1.8The size range of the LD optic should be appropriate to the spray generation device under study. For example, the upper bound of the smallest droplet size class reported by the instrument shall be not more than1/4the size ofDV0.1.1.9The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.10This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.11This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1This guide provides a means of using an LD instrument to obtain a droplet size distribution from a spray in gas co-flow that approximates a flux-sensitive sample.45.2In many sprays, the experimenter shall account for spatial segregation of droplets by size. This guide provides a means of spatial averaging the droplet distribution.5.3The results obtained will be statistical in nature and refer to the time average of droplet size distribution of the entire spray.5.4This guide is used to calibrate a spray generation device to produce a desired droplet size distribution under prespecified environmental and co-flow conditions or characterize an unknown spray while minimizing the uncertainty in the measurement.
2.[标准] Standard Test Method for Measuring Aspiration Potential of Aerosol Products

测量气溶胶产品吸入电位的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D7952-15(2021)

发布时间：
2021-11-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This test method covers a small-scale laboratory procedure to determine the aspiration potential of aerosol products by determining spray pattern and aerosol deposition rates.1.2This test method has been developed to address a need to identify which aerosol products may present an aspiration risk such that special labeling and/or child-resistant packaging would be appropriate. Studies based on this method may allow the development of a practice to identify such aerosol products.1.3Although this method may be useful for testing non-pressurized aerosol products, its development has been limited to testing pressurized aerosols.1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1This test method provides a means of measuring whether or not an aerosol product may present an aspiration risk if a dispensed aerosol gets into one’s mouth.4.2The degree of risk for aspiration of an aerosol depends both on spray pattern as well as aerosol deposition rate.24.3This test method will be used to determine the need for child-resistant packaging of aerosol products.
3.[标准] Aerosol containers - Metal containers with 25,4 mm aperture - Dimensions of valve cups

气溶胶容器 - 具有25,4 Mm孔径的金属容器 - 阀杯尺寸

发布单位：
国际组织-欧洲标准化委员会(IX-CEN)

标准状态：
现行

标准号：
EN 14848:2020

发布时间：
2020-01-15

中标分类：
B92 农业、林业 - 农、林机械与设备 - 畜牧、家禽机械与设备

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：
2020-01-15

摘要： This document specifies the critical dimensions of valve cups suitable for clinching into 25,4 mm aperture metal aerosol containers.This document is applicable to aperture metal aerosol containers which are used with the metal aerosol containers in accordance with EN 14847 and EN 15006.This European Standard does not specify dimples on aperture metal aerosol containers.NOTETo provide satisfactory filling in production, dimples are no longer considered essential but might still be used. Their presence could cause damage of the 25,4 mm aperture and their presence on lacquered cups can give rise to coating defects at the dimple feature. Thus, in the interest of simplicity and reduction of difficulties, dimples are excluded from this standard.
4.[标准] Aerosol containers - Compartmented aerosol dispensers

气溶胶容器.分隔式气溶胶分配器

发布单位：
国际组织-欧洲标准化委员会(IX-CEN)

标准状态：
现行

标准号：
EN 15009:2020

发布时间：
2020-10-07

中标分类：
L78 电子元器件与信息技术 - 信息处理技术 - 数据通信

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：
2020-10-07

摘要： This document specifies the relationship between the nominal volume of product and the maximum nominal brimful capacity of the outer container of the compartmented aerosol dispenser.
5.[标准] Commission Decision (EU) 2021/149 of 17 November 2020 on State aid SA.50707 2019/C (ex 2018/FC) – Spain – Air Nostrum fleet renewal (notified under document C(2020) 7913) (Only the Spanish version is authentic) (Text with EEA relevance)

委员会2020年11月17日关于国家援助的2021第149号决定（欧盟） 50707 2019/C（ex 2018/FC）-西班牙-诺斯特朗航空机队更新（根据文件C（2020）7913通知）（只有西班牙版本是真实的）（与欧洲经济区相关的文本）

发布单位：
-

标准状态：
现行

标准号：
32021D0149

发布时间：
2020-11-17

中标分类：
A14 综合 - 经济、文化 - 图书馆、档案、文献与情报工作

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： Commission Decision (EU) 2021/149 of 17 November 2020 on State aid SA.50707 2019/C (ex 2018/FC) – Spain – Air Nostrum fleet renewal (notified under document C(2020) 7913) (Only the Spanish version is authentic) (Text with EEA relevance)
6.[标准] Standard Test Method for Determining Liquid Drop Size Characteristics in a Spray Using Optical Nonimaging Light-Scattering Instruments

用光学非成像光散射仪器测定喷雾中液滴尺寸特性的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM E1260-03(2020)

发布时间：
2020-04-01

中标分类：
-

国标分类：
17.180.30 光学和光学测量 - 光学测量仪器

55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1The purpose of this test method is to obtain data which characterize the sizes of liquid particles or drops such as are produced by a spray nozzle or similar device under specified conditions using a specified liquid. The drops will generally be in the size range from 5-μm to the order of 1 000-μm diameter; they will occur in sprays which may be as small as a few cubic centimetres or as large as several cubic metres. Typically the number density of the particles can vary significantly from one point to another.1.2This test method is intended primarily for use in standardizing measurements of the performance of sprayproducing devices. It is limited to those techniques and instruments that operate by passing a beam of light through the spray and analyzing the light scattered by the droplets to derive size information. Such techniques do not produce images of individual drops, and therefore, are known as “optical (nonimaging) instruments.”1.3The measurements made, when referred to the entire spray being sampled, may be flux sensitive or spatial, as defined in PracticeE799, depending on the techniques used with a particular instrument.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1The purpose of this test method is to provide data on liquid drop-size characteristics for sprays, as indicated by optical nonimaging light-scattering instruments. The results obtained generally will be statistical in nature. The number of variables concerned in the production of liquid spray, together with the variety of optical, electronic, and sampling systems used in different instruments, may contribute to variations in the test results. Care must be exercised, therefore, when attempting to compare data from samples obtained by different means.
7.[标准] Standard Guide for Determining Cross-Section Averaged Characteristics of a Spray Using Laser-Diffraction Instruments in a Wind Tunnel Apparatus

在风洞设备中使用激光衍射仪测定喷雾横截面平均特性的标准指南

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
历史

标准号：
ASTM E2872-14(2019)

发布时间：
2019-10-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1The purpose of this guide is to define a test procedure for applying the laser diffraction (LD) method to estimate an average droplet size distribution that characterizes the flux of liquid droplets produced by a specified spray generation device under specified gas co-flow conditions using a specified liquid. The intended scope is limited to artificially generated sprays with high speed co-flow. The droplets are assumed to be in the size range of 1 to 2000 µm in diameter and occur in sprays that are contained within a volume as small as a few cubic centimetres or as large as a cubic metre. The droplet sizes are assumed to be distributed non-uniformly within the spray volume.1.2This guide is intended primarily to guide measurement of performance of nozzles and atomizers using LD instruments.1.3Non-uniform sprays require measurements across the entire spray cross section or through several chords providing a representative sample of the overall spray cross section. The aim of multiple-chord measurements is to obtain a single droplet size distribution that characterizes the whole spray rather than values from a single chordal measurement.1.4Use of this guide requires that the instrument does not interfere with spray production and does not significantly impinge upon or disturb the co-flow of gas and the spray. This technique is, therefore, considered non-intrusive.1.5The computation of droplet size distributions from the light-scattering distributions is done using Mie scattering theory or Fraunhofer diffraction approximation. The use of Mie theory accounts for light refracted through the droplet and there is a specific requirement for knowledge of both real (refractive) and imaginary (absorptive) components of the complex index of refraction. Mie theory also relies on an assumption of droplet homogeneity. The Fraunhofer diffraction approximation does not account for light refracted through the droplet and does not require knowledge of the index of refraction.1.6The instruments shall include data-processing capabilities to convert the LD scattering intensities into droplet size distribution parameters in accordance with PracticeE799and Test MethodE1260.1.7The spray is visible and accessible to the collimated beam produced by the transmitter optics of the LD instrument. The shape and size of the spray shall be contained within the working distance of the LD system optics as specified by the instrument manufacturer.1.8The size range of the LD optic should be appropriate to the spray generation device under study. For example, the upper bound of the smallest droplet size class reported by the instrument shall be not more than1/4the size ofDV0.1.1.9The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.10This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.11This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1This guide provides a means of using an LD instrument to obtain a droplet size distribution from a spray in gas co-flow that approximates a flux-sensitive sample.45.2In many sprays, the experimenter shall account for spatial segregation of droplets by size. This guide provides a means of spatial averaging the droplet distribution.5.3The results obtained will be statistical in nature and refer to the time average of droplet size distribution of the entire spray.5.4This guide is used to calibrate a spray generation device to produce a desired droplet size distribution under prespecified environmental and co-flow conditions or characterize an unknown spray while minimizing the uncertainty in the measurement.
8.[标准] Popravek Direktive Komisije (EU) 2016/2037 z dne 21. novembra 2016 o spremembi Direktive Sveta 75/324/EGS glede najvišjega dovoljenega tlaka aerosolnih razpršilnikov in za prilagoditev njenih določb o označevanju Uredbi (ES) št. 1272/2008 Evropskega parlamenta in Sveta o razvrščanju, označevanju in pakiranju snovi ter zmesi (UL L 314, 22.11.2016)

第21号委员会指令（EU）2016/2037勘误表 2016年11月22日欧洲议会和理事会第1272/2008号法规（EC）修订了关于气溶胶分配器最大允许压力的理事会指令75/324/EEC 并将其标签规定修改为欧洲议会和理事会关于物质和混合物分类、标签和包装的第1272/2008号法规（OJ L 3142016年11月22日）

发布单位：
-

标准状态：

标准号：
32016L2037R(02)

发布时间：
2018-02-17

中标分类：
A80 综合 - 标志、包装、运输、贮存 - 标志、包装、运输、贮存综合

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：
9.[标准] Standard Practice for Number of Strokes to Prime a Mechanical Pump Dispenser

给机械泵分配器注水的冲程数的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D3890-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the determination of the number of actuations required to prime a pump dispenser (spray and flow types) with a consumer-type product.1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======2.1This practice can be used to visually compare priming characteristics of different pump dispensers and different products.2.2This practice is suitable for establishing specifications for both the pump dispenser and the final package.
10.[标准] Standard Practice for Compatibility of Mechanical Pump Dispenser Components

机械泵分配器组件兼容性的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D4333/D4333M-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers testing of the components of mechanical pump dispensers (spray or flow types) for compatibility with products.1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======2.1This practice identifies the compatibility of the mechanical pump dispenser components with consumer-type products.
11.[标准] Standard Practice for Determination of the Output Per Stroke of a Mechanical Pump Dispenser

机械泵分配器每冲程输出量测定的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D4336-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the measurement of the mean quantity-by-weight of liquids dispensed from a mechanical pump dispenser (spray or flow type) with a consumer-type product on each actuation.1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1This practice can be used to compare the output per stroke of different pump dispensers for the purpose of establishing dosage and use instructions for products of consumer usage.3.2This practice is suitable for establishing specifications for both the pump dispenser and the final package.
12.[标准] Standard Practice for Rapid Pressure Determination of Pressurized Products (Withdrawn 2023)

加压产品的快速压力测定的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
作废

标准号：
ASTM D3070-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers rapid pressure determination for pressurized products.1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======2.1This practice is a rapid technique for quality control, formula development, etc., where speed is necessary and a high degree of accuracy is not essential.
13.[标准] Standard Practice for Effective Crimping on Outside Crimped Valves of Aerosol Containers (Withdrawn 2023)

气雾剂容器外压接阀有效压接的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
作废

标准号：
ASTM D3076-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the effective crimping on outside crimped valves within the wide parameters of containers and valves available.1.2Practices appear in the following order:SectionsOptical Comparator Practice4to7Caliper Practice8to121.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======5.1This practice provides information for the establishment of quality control procedures on filling lines.
14.[标准] Standard Practice for Seepage Rate of Aerosol Products (Withdrawn 2023)

气溶胶产品渗透速率的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
作废

标准号：
ASTM D3094-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the determination of approximate mass loss due to valve seepage rate2of aerosol products by the collection and measurement of gases seeping through the valve and into a special eudiometer tube, over a relatively short time period.1.2It can be shown that the average refrigeration-filled aerosol product seeps to the extent of approximately 3.0 mL when the corresponding mass loss is 0.10 oz (2.9 cm3)/year. This figure is partially based on air content and is subject to variations according to filling conditions. This practice is not considered dependable when applied to pressure-filled, unpurged aerosol products.1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======2.1This practice affords a more rapid answer to the ever-present problem of mass loss during storage. It is of particular value in determining the effectiveness of valve stake and clinch seal elastomers in contact with new formulations. This practice may also be used to evaluate new valves with standard mixtures.
15.[标准] Standard Practice for Determining the Peak Force-to-Actuate of a Mechanical Pump Dispenser

测定机械泵分配器的最大驱动力的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6534-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser.1.2The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific precautionary statements are given in Section5.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
16.[标准] Standard Practice for Determining the Dip Tube Length of a Mechanical Pump Dispenser

测定机械泵分配器浸渍管长度的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6535/D6535M-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the determination technique for a dip tube of a mechanical pump dispenser.1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======2.1This practice is to be used to determine the length of a dip tube of a mechanical pump dispenser that extends to the bottom-corner of a container.2.2This practice is to be used to determine the length of a dip tube of a mechanical pump dispenser that extends to the bottom-center of a container.
17.[标准] Standard Practice for Measuring the Dip Tube Length of a Mechanical Pump Dispenser

测量机械泵分配器的浸渍管长度的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6536/D6536M-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the measurement technique for a dip tube of a mechanical pump dispenser.1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======2.1This practice is to be used to measure the length of a specified dip tube from the bottom of the sealing surface to the end of the dip tube in a mechanical pump dispenser.2.2This practice is to be used to measure the exposed length of a specified dip tube of a mechanical pump dispenser.
18.[标准] Standard Practice for Basic Functional Stability of a Mechanical Pump Dispenser

机械泵分配器基本功能稳定性的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6633-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the determination of the basic functional stability of a mechanical pump dispenser with a product.1.2This practice covers accelerated usage evaluations of mechanical pump dispensers (spray or flow types) with a product.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.Specific precautions are given in Section5.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1This practice is used for determining the accelerated usage of a mechanical pump dispenser for consumer usage.
19.[标准] Standard Practice for Basic Storage Stability of a Mechanical Pump Dispenser

机械泵分配器基本贮存稳定性的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM D6654-18

发布时间：
2018-05-01

中标分类：
-

国标分类：
19.060 试验 - 机械试验

55.130 货物的包装和调运 - 雾化剂罐

实施时间：

摘要： 1.1This practice covers the determination of the basic storage stability of a mechanical pump dispenser with a product.1.2This practice covers an evaluation of the weight lost during storage of mechanical pump dispensers (spray or flow types) with a product.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======3.1Determining the storage of a mechanical pump dispenser for consumer usage. Products of consumer usage are of the personal care, household, insecticides, food, automotive, and institutional nature. Pharmaceutical and cosmetic products including perfume are not covered under this practice.
20.[标准] Aerosol containers - Aluminium containers - Dimensions of one-piece cans with 25,4 mm aperture

气溶胶容器 - 铝容器 - 具有25,4 mm孔径的单件罐的尺寸

发布单位：
国际组织-欧洲标准化委员会(IX-CEN)

标准状态：
现行

标准号：
EN 15008:2017

发布时间：
2017-03-22

中标分类：
J50/59 机械 - 金属切削机床

国标分类：
55.130 货物的包装和调运 - 雾化剂罐

实施时间：
2017-03-22

摘要： This European Standard specifies the dimensions and volumes for one-piece aluminium aerosol containers with a 25,4 mm aperture.This European Standard applies to one-piece containers of monobloc construction with an ogival, spherical or flat shoulder.