国际标准化组织_国内外标准网文献检索下载

1.[标准] Best practices on the selection and use of personal protective equipment (PPE) designed to provide protection for firefighters

选择和使用为消防员提供保护的个人防护装备的最佳实践

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO/TR 21808:2024

发布时间：
2024-01-09

中标分类：
-

国标分类：
13.340.10 防护设备 - 防护服装

实施时间：

摘要： This document sets out the best practices for the selection and use of PPE designed to provide protection for firefighters while carrying out their duties.The PPE covered in this document is intended for firefighting personnel exposed to risks associated with but not necessarily limited to the following activities:—？structural firefighting;—？wildland firefighting;—？incidents involving hazardous materials;—？incidents involving motor vehicle;—？urban search and rescue.The purpose of this document is to highlight the main areas that a fire service needs to consider when providing PPE to its members. This document is a supplement to the information provided in the PPE standards or used in conjunction with them. Most paragraphs of the document contain bullet lists, these lists are provided for guidance only and they are not exhaustive.Cleaning, inspection and repair of firefighters' personal protective equipment (including care and maintenance) are covered by ISO 23616.
2.[标准] Information technology — Multimedia content description interface — Part 17: Compression of neural networks for multimedia content description and analysis

信息技术多媒体内容描述接口第17部分:多媒体内容描述和分析用神经网络的压缩

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO/IEC 15938-17:2024

发布时间：
2024-01-10

中标分类：
-

国标分类：
-

实施时间：

摘要： This document specifies Neural Network Coding (NNC) as a compressed representation of the parameters/weights of a trained neural network and a decoding process for the compressed representation, complementing the description of the network topology in existing (exchange) formats for neural networks. It establishes a toolbox of compression methods, specifying (where applicable) the resulting elements of the compressed bitstream. Most of these tools can be applied to the compression of entire neural networks, and some of them can also be applied to the compression of differential updates of neural networks with respect to a base network. Such differential updates are for example useful when models are redistributed after fine-tuning or transfer learning, or when providing versions of a neural network with different compression ratios.This document does not specify a complete protocol for the transmission of neural networks, but focuses on compression of network parameters. Only the syntax format, semantics, associated decoding process requirements, parameter sparsification, parameter transformation methods, parameter quantization, entropy coding method and integration/signalling within existing exchange formats are specified, while other matters such as pre-processing, system signalling and multiplexing, data loss recovery and post-processing are considered to be outside the scope of this document. Additionally, the internal processing steps performed within a decoder are also considered to be outside the scope of this document; only the externally observable output behaviour is required to conform to the specifications of this document.
3.[标准] Oil and gas industries including lower carbon energy — Specific requirements for offshore structures — Part 3: Topsides structure

包括低碳能源在内的石油和天然气工业海上结构的特殊要求第3部分:上部结构

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 19901-3:2024

发布时间：
2024-01-10

中标分类：
-

国标分类：
75.180.10 石油和天然气工业设备 - 勘探和钻采设备

实施时间：

摘要： This document provides requirements, guidance and information for the design and fabrication of topsides structure for offshore structures, including in-service, pre-service and post-service conditions.The actions on topsides structure and the action effects in structural components are derived from this document, where necessary in combination with other International Standards in the ISO 19901 series (e.g. ISO 19901-1 for wind actions - see 7.6.2, ISO 19901-2 for seismic actions - see 7.7) and ISO 19902 for fatigue design (see 6.7).This document is applicable to the following:—？topsides of fixed offshore structures;—？discrete structural units placed on the hull structures of floating offshore structures and mobile offshore units;—？topsides of arctic offshore structures, excluding winterization (see ISO？19906).If any part of the topsides structure forms part of the primary structure of the overall structural system which resists global platform actions, the requirements of this document are supplemented with applicable requirements in ISO？19902, ISO？19903, ISO？19904-1, ISO？19905-1, ISO？19905-3 and ISO？19906.For those parts of floating offshore structures and mobile offshore units that are chosen to be governed by the rules of a recognized classification society, the corresponding class rules supersede the associated requirements of this document.This document also addresses prevention, control and assessment of fire, explosions and other accidental events.The fire and explosion provisions of this document can be applied to those parts of the hulls of floating structures and mobile offshore units that contain hydrocarbon processing, piping or storage.NOTE？Requirements for structural integrity management are presented in ISO 19901-9.This document applies to structural components including the following:—？primary and secondary structure in decks, module support frames and modules;—？flare structures;—？crane pedestal and other crane support arrangements;—？helicopter landing decks (helidecks);—？permanent bridges between separate offshore structures;—？masts, towers and booms on offshore structures.This document provides requirements for selecting and using a national building standard with a correspondence factor for determining the resistance of rolled and welded non-circular prismatic components and their connections.
4.[标准] Metallic and other inorganic coatings — Review of methods of measurement of thickness

金属和其他无机涂层厚度测量方法综述

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 3882:2024

发布时间：
2024-01-10

中标分类：
-

国标分类：
25.220.40 表面处理和镀涂 - 金属镀层

25.220.20 表面处理和镀涂 - 表面处理

实施时间：

摘要： This document reviews methods for measuring the thickness of metallic and other inorganic coatings on both metallic and non-metallic substrates (see Tables？1, A.1 and A.2). It is limited to tests already specified, or to be specified, in International Standards and excludes certain tests that are used for special applications.
5.[标准] Drinking water, wastewater and stormwater systems and services — Guidelines for the provision of alternative water service for essential facilities during a crisis

饮用水、废水和雨水系统和服务——危机期间为基本设施提供替代水服务的指南

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 24595:2024

发布时间：
2024-01-10

中标分类：
-

国标分类：
13.060.01 水质 - 水质综合

03.080.30 服务 - 消费者服务

实施时间：

摘要： This document provides guidelines for alternative water service (AWS) provision during a crisis for the ongoing operation of essential facilities.This document addresses:—？AWS principles and methods;—？AWS operational planning and implementation.This document is not applicable to:—？planned water supply interruptions forming part of the drinking water utility's normal operations;NOTE？However, many of the principles and methods described can be appropriate in such circumstances.—？water supplied to temporary settlements, such as refugee camps;—？the development and implementation of a crisis management system for water service, which is covered by ISO 24518[1] and ISO/TS 24520,[2] or the development and implementation of AWS provision during a crisis for private users, which is covered by ISO 24527.[3]
6.[标准] Petroleum products and lubricants — Determination of the mechanical stability of greases in presence of water

石油产品和润滑剂.润滑脂在水中机械稳定性的测定

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 12921:2024

发布时间：
2024-01-10

中标分类：
-

国标分类：
75.100 石油及相关技术 - 润滑剂、工业油及相关产品

实施时间：

摘要： This document specifies a method for evaluating the change of consistency of a grease when it is submitted to working and prolonged working in presence of 10？% of water.
7.[标准] Soft soldering fluxes — Test methods — Part 17: Surface insulation resistance comb test and electrochemical migration test of flux residues

软钎焊焊剂试验方法第17部分:焊剂残留物的表面绝缘电阻梳形试验和电化学迁移试验

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 9455-17:2024

发布时间：
2024-01-10

中标分类：
-

国标分类：
25.160.50 焊接、钎焊和低温焊 - 钎焊和低温焊

实施时间：

摘要： This document specifies a method of testing for deleterious effects that can arise from flux residues after soldering or tinning test coupons. The test is applicable to type？1 and type？2 fluxes, as specified in ISO？9454-1, in solid or liquid form, or in the form of flux-cored solder wire, solder preforms or solder paste constituted with eutectic or near-eutectic tin/lead (Sn/Pb) or Sn95,5Ag3Cu0,5 or other lead-free solders as agreed between user and supplier (see ISO？9453).This test method is also applicable to fluxes for use with lead-containing and lead-free solders. However, the soldering temperatures can be adjusted with agreement between tester and customer.
8.[标准] Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience

金属材料焊接工艺规范和评定——基于以往焊接经验的评定

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 15611:2024

发布时间：
2024-01-10

中标分类：
-

国标分类：
25.160.01 焊接、钎焊和低温焊 - 焊接、钎焊和低温焊综合

实施时间：

摘要： This document gives the necessary information to explain the requirements referenced in ISO？15607 about the qualification of welding procedures based on previous welding experience.In addition, it gives the range of qualification.The use of this document can be restricted by an application standard or a specification.
9.[标准] Geographic information — Land Administration Domain Model (LADM) — Part 1: Generic conceptual model

地理信息——土地管理领域模型（LADM）——第1部分:通用概念模型

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 19152-1:2024

发布时间：
2024-01-09

中标分类：
-

国标分类：
35.240.70 信息技术应用 - 信息技术在自然科学中的应用

实施时间：

摘要： This document:—？defines a reference Land Administration Domain Model (LADM) covering basic information-related components of land administration/georegulation;—？provides an abstract, conceptual model with packages related to:—？parties (people and organizations),—？basic administrative units, rights, responsibilities and restrictions (RRRs),—？spatial units,—？a generic conceptual model (sources and versioned object);—？provides terminology for land administration/georegulation, based on various national and international systems, that is as simple as possible in order to be useful in practice. The terminology allows a shared description of different formal or informal practices and procedures in various jurisdictions;—？provides a content model independent of encoding, allowing for the support of various encodings;—？provides a basis for national and regional profiles;—？enables the combining of land administration/georegulation information from different sources in a coherent manner.The following are outside the scope of this document:—？interference with (national) land administration/georegulation laws with potentially legal implications due to the possibility of describing different types of systems but in the same notation;—？construction of external databases with party data, address data, land cover data, physical utility network data, archive data and taxation data. However, the LADM provides stereotype classes for these data sets to indicate which data set elements the LADM expects from these external sources, if available.This document provides the concepts and basic structure for standardization in the land administration/georegulation domain. It defines a general schema that permits regulatory information to be described. It also allows for the relationship to multiple parties and groups to be expressed together with a referencing structure so that sourcing of all information systems can be maintained. This document establishes the common elements and basic schema upon which more detailed schema can be established.
10.[标准] Clamp-in tyre valves for tyre pressure monitoring systems — Part 2: Test methods and performance

轮胎压力监测系统用夹式轮胎气门嘴第2部分:试验方法和性能

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 24163-2:2024

发布时间：
2024-01-09

中标分类：
-

国标分类：
83.160.01 轮胎 - 轮胎综合

实施时间：

摘要： This document specifies test methods for clamp-in tyre valves for tyre pressure monitoring systems (TPMSs).These methods are defined to determine the minimum level of performance requested.This document applies to the tyre valve assembled on the rim hole with diameter of 11,3？mm for passenger cars or for light duty vehicles.
11.[标准] Space systems — Design, testing and operation of a large constellation of spacecraft

航天系统大型航天器星座的设计、测试和运行

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO/TS 6434:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
49.140 航空器和航天器工程 - 航天系统和操作装置

实施时间：

摘要： This document provides requirements that are either unique or particularly relevant to large constellations of spacecraft operating in the LEO protected region throughout their life cycle, including planning, designing, testing, operating and disposal activities.The requirements in this document are applicable to large constellation owners. While some are directly applicable to the constellation owners, others are allocated to the manufactures or operators under the responsibility of the constellation owners.
12.[标准] Fire detection and alarm systems — Part 29: Video fire detectors

火灾探测和报警系统第29部分:视频火灾探测器

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 7240-29:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
13.220.20 消防 - 防火

实施时间：

摘要： This document specifies requirements, test methods and performance criteria for video fire detectors (VFDs), which operate in the visible spectrum, for use in fire detection and alarm systems installed in and around buildings (see ISO？7240-1). For the testing of other types of VFD working on different principles, this document can be used only for guidance.Detectors developed for the protection of specific risks that incorporate special characteristics (including additional features or enhanced functionality for which this document does not define a test or assessment method) are beyond the scope of this document.
13.[标准] Pneumatic fluid power — Compressed air pressure regulators and filter-regulators — Part 1: Main characteristics to include in supplier's literature and product-marking requirements

气动流体动力.压缩空气压力调节器和过滤调节器.第1部分:包括在供应商文献和产品标记要求中的主要特性

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 6953-1:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
23.100.50 流体动力系统 - 控制部件

实施时间：

摘要： This document specifies which characteristics of compressed air pressure regulators are required to be included in the literature from the supplier. It also applies to filter-regulators.This document applies to:—？manually controlled direct operated types (with relieving mechanisms such as a relieving pressure regulator, or without relieving mechanism),—？manually controlled internal pilot operating types (e.g. nozzle flapper), and—？pressure-pilot operated types.In addition, it specifies the product marking requirements for pressure regulators and filter-regulators.This document is applicable to compressed air pressure regulators with a rated inlet pressure of up to 2 500 kPa (25 bar)？and an outlet adjustment pressure of up to 1？600？kPa (16？bar) and to filter-regulators with rated inlet and outlet pressures of up to 1？600？kPa (16？bar), in which the major contaminants are removed by mechanical means.NOTE？The main characteristics to be included in the supplier's literature related to electrically modulated pneumatic continuous pressure control valves are specified in ISO？10094-1.？
14.[标准] Identification cards — Card service life — Part 2: Methods of evaluation

身份证使用寿命第2部分:评定方法

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO/IEC 24789-2:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
35.240.15 信息技术应用 - 识别卡和有关装置

实施时间：

摘要： This document provides methods of evaluation for ID-1 identification card service life for the applications provided in ISO/IEC 24789-1.The listed evaluation methods represent available tests, not mandatory tests. The selection of mandatory tests is listed in ISO/IEC 24789-1.
15.[标准] Artificial intelligence — Functional safety and AI systems

人工智能——功能安全与人工智能系统

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO/IEC TR 5469:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
35.020 信息技术、办公机械 - 信息技术(IT)综合

实施时间：

摘要： This document describes the properties, related risk factors, available methods and processes relating to:—？use of AI inside a safety related function to realize the functionality;—？use of non-AI safety related functions to ensure safety for an AI controlled equipment;—？use of AI systems to design and develop safety related functions.
16.[标准] Environmental management for concrete and concrete structures — Part 1: General principles

混凝土和混凝土结构的环境管理第1部分:一般原则

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 13315-1:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
91.080.40 建筑物结构 - 混凝土结构

13.020.10 环境保护 - 环境管理

91.100.30 建筑材料 - 混凝土和混凝土制品

实施时间：

摘要： This document provides a framework and basic rules on environmental management related to concrete and concrete structures. This includes the assessment of the environmental impacts and methods of implementing environmental improvement based on the assessment.This document is used for the environmental consideration in activities related to the production of concrete constituents, the production, recycling and disposal of concrete, and the design, execution, use and demolition of concrete structures. It is applied for their entire lifecycles, respective stages of the lifecycles, or certain ranges of the lifecycles. This document is applicable to newly produced concrete and newly constructed concrete structures, and also existing concrete and concrete structures.This document applies to single concretes, concrete families, single concrete structures, and concrete structure complexes. For materials other than concrete, the related ISO standards are applied where available. In the case where no ISO standard is available, such materials are appropriately dealt with referring to this document and the normative references.This document covers global, regional and local environments. This document does not directly deal with the environmental impacts resulting from the operation of equipment installed in concrete structures. However, the special properties of concrete and concrete structures affecting the operational efficiency of such equipment are considered in this document.This document covers secondary effects of the production of concrete and execution of concrete structures.NOTE？The secondary effects of the production of concrete include the future possibility of leaching of heavy metals from concrete or the absorption of heavy metals from the environment, the effect of waste treatments on the environment, etc.This document covers the economic and social effects of environmental consideration in the production of concrete and execution of concrete structures.
17.[标准] Identification cards — Card service life — Part 1: Application profiles and requirements

识别卡使用寿命第1部分:应用概况和要求

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO/IEC 24789-1:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
35.240.15 信息技术应用 - 识别卡和有关装置

实施时间：

摘要： This document comprises a methodology for determining a test plan to simulate a card's service life. The methodology defines two parameters of card service life: the expected card service life in years and the average number of uses per day.This document and ISO/IEC 24789-2, together along with ISO/IEC 10373-1 describe the evaluation methods to be used and their criteria.This document was originally developed for ID-1 cards conforming to ISO/IEC 7810 but can be useful in whole or in part for other types and form factors.
18.[标准] Water quality — Radium 226 — Test method using ICP-MS

水质镭226 ICP-MS试验方法

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 4685:2024

发布时间：
2024-01-09

中标分类：
-

国标分类：
13.060.60 水质 - 水的物理特性检验

17.240 计量学和测量、物理现象 - 辐射测量

实施时间：

摘要： This document specifies methods to determine 226Ra concentration by inductively coupled plasma mass spectrometry (ICP-MS). The mass concentrations obtained can be converted into activity concentrations.The method is applicable to test samples of drinking water, rainwater, surface and ground water, after proper sampling and handling, and test sample preparation.The detection limit depends on the sample volume, the instrument used, the background count rate, the detection efficiency, the counting time and the chemical yield. The detection limit of the method described in this document, using currently available equipment, is approximately 10？mBq·l-1, which is better than the WHO criteria for safe consumption of drinking water (1？Bq·l-1).This method covers the measurement of 226Ra in water at activity concentrations between 0,001？Bq·l？1 and 100？Bq·l？1. Samples with concentrations higher than 1？Bq·l？1 can be measured if a dilution is performed.The method described in this document is applicable in the event of an emergency situation.In this method, filtration of the test sample is necessary. The analysis of 226Ra adsorbed to suspended matter is not covered by this method. The analysis of the insoluble fraction requires a mineralization step that is not covered by this document. In this case, the measurement is made on the different phases obtained.It is the user’s responsibility to ensure the validity of this test method for the water samples tested.
19.[标准] Environmental solid matrices — Determination of elements using inductively coupled plasma optical emission spectrometry (ICP-OES)

环境固体基质电感耦合等离子体发射光谱法（ICP-OES）测定元素

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 22036:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
13.080.10 土质、土壤学 - 土壤的化学特性

实施时间：

摘要： This document specifies a method for the determination of the following elements in aqua regia, nitric acid or mixture of hydrochloric (HCl), nitric (HNO3) and tetrafluoroboric (HBF4)/hydrofluoric (HF) acid digests of soil, treated biowaste, waste, sludge and sediment:Aluminium (Al), antimony (Sb), arsenic (As), barium (Ba), beryllium (Be), bismuth (Bi), boron (B), cadmium (Cd), calcium (Ca), cerium (Ce), chromium (Cr), cobalt (Co), copper (Cu), dysprosium (Dy), erbium (Er), europium (Eu), gallium (Ga), gadolinium (Gd), germanium (Ge), gold (Au), hafnium (Hf), holmium (Ho), indium (In), iridium (Ir), iron (Fe), lanthanum (La), lead (Pb), lithium (Li), lutetium (Lu) magnesium (Mg), manganese (Mn), mercury (Hg), molybdenum (Mo), neodymium (Nd), nickel (Ni), palladium (Pd), phosphorus (P), platinum (Pt), potassium (K), praseodymium (Pr), rhodium (Rh), ruthenium (Ru), samarium (Sm), scandium (Sc), selenium (Se), silicon (Si), silver (Ag), sodium (Na), strontium (Sr), sulfur (S), tantalum (Ta), tellurium (Te), terbium (Tb), thallium (Tl), thulium (Tm), thorium (Th), tin (Sn), titanium (Ti), tungsten (W), vanadium (V), yttrium (Y), ytterbium (Yb), zinc (Zn) and zirconium (Zr).The method is also applicable to other extracts or digests originating from, for example, DTPA extraction, fusion methods or total digestion methods, provided the user has verified the applicability.The method has been validated for the elements given in Table？A.1 (sludge), Table？A.2 (compost) and Table？A.3 (soil). The method is applicable for other solid matrices and other elements as listed above, provided the user has verified the applicability.This method is also applicable for the determination of major, minor and trace elements in aqua regia and nitric acid digests and in eluates of construction products (EN 17200[22]).NOTE？Construction products include e.g. mineral-based products; bituminous products; metals; wood-based products; plastics and rubbers; sealants and adhesives; paints and coatings.
20.[标准] Traditional Chinese medicine — Rehmannia glutinosa root

中药地黄

发布单位：
国际组织-国际标准化组织(IX-ISO)

标准状态：
现行

标准号：
ISO 9109:2024

发布时间：
2024-01-08

中标分类：
-

国标分类：
11.120.10 制药学 - 药物

实施时间：

摘要： This document specifies the requirements and test methods for dried Rehmannia glutinosa root that is derived from Rehmannia glutinosa Libosch.Fresh Rehmannia glutinosa Libosch. and processed Rehmannia glutinosa Libosch. are excluded.This document is applicable to Rehmannia glutinosa root that is sold and used as a natural medicine in international trade, including Chinese materia medica (whole medicinal materials) and decoction pieces derived from this plant.