滤波器_国内外标准网文献检索下载

1.[标准] Passive filter units for electromagnetic interference suppression - Part 3: Passive filter units for which safety tests are appropriate

电磁干扰抑制用无源滤波装置.第3部分:安全试验适用的无源滤波装置

发布单位：
国际组织-国际电工委员会(IX-IEC)

标准状态：
现行

标准号：
IEC 60939-3:2024 RLV

发布时间：
2024-02-12

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：

摘要： IEC 60939-3:2024 RLV contains both the official IEC International Standard and its Redline version. The Redline version is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.IEC 60939-3:2024 covers passive filters used to attenuate unwanted radio-frequency signals (such as noise or interference) generated from electromagnetic sources. Both single and multi-channel filters within one enclosure or which are built on a printed circuit board forming a compact entity are included within the scope of this document. This document applies to passive filter units for electromagnetic interference suppression for which safety tests are appropriate. This implies that filters specified according to this document will either be connected to mains supplies, when compliance with the mandatory tests of Table B.1 is necessary, or used in other circuit positions where the equipment specification specifies that some or all of these safety tests are required. This document applies to passive filter units, which will be connected to an AC mains or other supply (DC or AC) with a nominal voltage not exceeding 1 000 V AC, with a nominal frequency not exceeding 400 Hz, or 1 500 V DC. Note: For AC use, IEC 60384-14 applies to capacitors which will be connected to AC mains with a nominal frequency not exceeding 100 Hz. This document covers appliance filters (US) but does not cover facility filters, cord-connected filters or direct plug-in filters. These other filters will be covered by another sectional specification.This edition includes the following significant technical changes with respect to the previous edition:a) separated clauses for safety and performance tests;b) added note for use of multiple X capacitors bridging basic insulation in 3 phase filters;c) characteristics and conditions to substitute X and Y capacitors are now described in a separate Subclause 4.1;d) creepage and clearance tables updated and in line with the latest editions of IEC 60938-2 and IEC 60664-1;e) allowing voltage measurement for inductance measurements (7.3);f) added requirements for marking depending on remaining energy after disconnection;g) added content of CTL DSH 2044:2016 for temperature test of IEC filters;h) added note about temperature rise required specimens for safety testing;i) changed index of capacitors in Annex A to avoid confusion between index name and capacitor class;j) moved tests from group 1A to 2. Now, samples in group 1A need to be submitted without potting;k) revision of all parts of the document has taken place based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents. Annex X contains all cross-references of changes in clause/subclause numbers.
2.[标准] Passive filter units for electromagnetic interference suppression - Part 3: Passive filter units for which safety tests are appropriate

电磁干扰抑制用无源滤波装置.第3部分:安全试验适用的无源滤波装置

发布单位：
国际组织-国际电工委员会(IX-IEC)

标准状态：
现行

标准号：
IEC 60939-3:2024

发布时间：
2024-02-12

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：

摘要： IEC 60939-3:2024 is available as IEC 60939-3:2024 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60939-3:2024 covers passive filters used to attenuate unwanted radio-frequency signals (such as noise or interference) generated from electromagnetic sources. Both single and multi-channel filters within one enclosure or which are built on a printed circuit board forming a compact entity are included within the scope of this document. This document applies to passive filter units for electromagnetic interference suppression for which safety tests are appropriate. This implies that filters specified according to this document will either be connected to mains supplies, when compliance with the mandatory tests of Table B.1 is necessary, or used in other circuit positions where the equipment specification specifies that some or all of these safety tests are required. This document applies to passive filter units, which will be connected to an AC mains or other supply (DC or AC) with a nominal voltage not exceeding 1 000 V AC, with a nominal frequency not exceeding 400 Hz, or 1 500 V DC. Note: For AC use, IEC 60384-14 applies to capacitors which will be connected to AC mains with a nominal frequency not exceeding 100 Hz. This document covers appliance filters (US) but does not cover facility filters, cord-connected filters or direct plug-in filters. These other filters will be covered by another sectional specification.This edition includes the following significant technical changes with respect to the previous edition:a) separated clauses for safety and performance tests;b) added note for use of multiple X capacitors bridging basic insulation in 3 phase filters;c) characteristics and conditions to substitute X and Y capacitors are now described in a separate Subclause 4.1;d) creepage and clearance tables updated and in line with the latest editions of IEC 60938-2 and IEC 60664-1;e) allowing voltage measurement for inductance measurements (7.3);f) added requirements for marking depending on remaining energy after disconnection;g) added content of CTL DSH 2044:2016 for temperature test of IEC filters;h) added note about temperature rise required specimens for safety testing;i) changed index of capacitors in Annex A to avoid confusion between index name and capacitor class;j) moved tests from group 1A to 2. Now, samples in group 1A need to be submitted without potting;k) revision of all parts of the document has taken place based on the ISO/IEC Directives, Part 2:2021, and harmonization with other similar kinds of documents. Annex X contains all cross-references of changes in clause/subclause numbers.
3.[标准] 连接处设有固定组件滤波器

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/QGCML 2079-2023

发布时间：
2023-11-08

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：
2023-12-01

摘要：主要技术内容:本文件规定了连接处设有固定组件滤波器的术语和定义、构成及原理、技术要求、试验方法、检验规则、标志、包装、运输及贮存。本文件适用于连接处设有固定组件滤波器的生产及检验
4.[标准] 分布式发电及配电网系统无源滤波装置

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/CEEIA 675-2023

发布时间：
2023-03-27

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：
2023-03-27

摘要：范围:本文件规定了无源滤波装置（以下简称滤波装置）的术语和定义、功能要求、使用条件、技术要求、试验类别、试验项目、试验条件、试验方法、标志、包装、运输与储存等内容。本文件适用于交流频率50Hz、标称电压35kV及以下的分布式发电系统及输变电配电网系统中，采用机电开关或电子型开关投切的滤波装置;主要技术内容:本文件规定了无源滤波装置（以下简称滤波装置）的术语和定义、功能要求、使用条件、技术要求、试验类别、试验项目、试验条件、试验方法、标志、包装、运输与储存等内容。本文件适用于交流频率50Hz、标称电压35kV及以下的分布式发电系统及输变电配电网系统中，采用机电开关或电子型开关投切的滤波装置
5.[标准] 滤波器内部防震装置

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/QGCML 2080-2023

发布时间：
2023-11-08

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：
2023-12-01

摘要：主要技术内容:本文件规定了滤波器内部防震装置的术语和定义、构成及原理、技术要求、试验方法、检验规则、标志、包装、运输及贮存。本文件适用于滤波器内部防震装置的生产及检验
6.[标准] 用在于射频仪器上的抗干扰组件

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/QGCML 903-2023

发布时间：
2023-06-13

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：
2023-06-28

摘要：主要技术内容:本文件规定了用于射频仪器上的抗干扰组件的术语和定义、装置构成及原理、要求、试验方法、检验规则、标志、包装、运输及贮存。本文件适用于射频仪器上抗干扰组件的生产与检验
7.[标准] 方便角度调节滤波器安装机柜

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/QGCML 2078-2023

发布时间：
2023-11-08

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：
2023-12-01

摘要：主要技术内容:本文件规定了方便角度调节滤波器安装机柜的术语和定义、构成及原理、技术要求、试验方法、检验规则、标志、包装、运输及贮存。本文件适用于方便角度调节滤波器安装机柜的生产及检验
8.[标准] Passive filter units for electromagnetic interference suppression - Part 2: Sectional specification - Passive filter units for which safety tests are appropriate - Test methods and general requirements

电磁干扰抑制用无源滤波装置第2部分:分规范安全试验适用的无源滤波装置试验方法和一般要求

发布单位：
国际组织-国际电工委员会(IX-IEC)

标准状态：
现行

标准号：
IEC 60939-2:2005+AMD1:2023 CSV

发布时间：
2023-08-17

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：

摘要： IEC 60939-2:2005+AMD1:2023 applies to passive filter units for electromagnetic interference suppression which fall within the scope of the Generic Specification IEC 60939-1. The scope of this Sectional specification is restricted to passive filter units for which safety tests are appropriate. This implies that filters specified according to this Sectional specification will either be connected to mains supplies, when compliance with the mandatory tests of Table 3 is necessary, or used in other circuit positions where the equipment specification prescribes that some or all of these safety tests are required.
9.[标准] Amendment 1 - Passive filter units for electromagnetic interference suppression - Part 2: Sectional specification - Passive filter units for which safety tests are appropriate - Test methods and general requirements

修改件1.电磁干扰抑制用无源滤波单元.第2部分:分规范.安全试验适用的无源滤波单元-试验方法和一般要求

发布单位：
国际组织-国际电工委员会(IX-IEC)

标准状态：
现行

标准号：
IEC 60939-2:2005/AMD1:2023

发布时间：
2023-08-17

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：
10.[标准] 전자기 간섭 억제용 수동 필터류 — 제2부: 품종 규격 — 안전 시험이 적절한 수동 필터류 — 시험방법과 일반 요구사항

电磁干扰抑制用无源滤波装置第2部分:分规范安全试验适用的无源滤波装置试验方法和一般要求

发布单位：
韩国-韩国标准(KR-KS)

标准状态：
现行

标准号：
KS C IEC 60939-2-2023

发布时间：
2023-03-06

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：

摘要： 이 표준은 품목 규격 KS C IEC 60939-1의 범위에 해당하는 전자기 간섭 억제용 수동 필터에 적용된다. 이 표준은 안전 시험이 적절한 전자기 간섭 억제용 수동 필터에 적용한다. 이것은 이 표준에 명시된 필터는 주 전원에 연결되거나, 혹은 회로의 다른 부분에서 사용되며 장비 사양에서 일부 혹은 모든 안전 시험이 요구된다고 지시함을 의미한다. 이 표준은 교류 전원 또는 기타 공급선(직류 또는 교류)에 연결되었을 때, 정격 전압이 교류 1 000 V 이하이면서 공칭 주파수 400 Hz 이하이거나, 또는 정격 전압이 직류 1 000 V인 필터에 적용한다.
11.[标准] 石墨烯声表面波滤波器结构制备规范

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/NSSQ 008-2022

发布时间：
2022-11-25

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：
2022-11-28

摘要：范围:本文件适用于石墨烯声表面波滤波器结构领域;主要技术内容:本文件规定了石墨烯声表面波滤波器结构制备规范的术语和定义并对包括压电基片清洗、制备金属电极层、制作变形组件、制备石墨烯层等进行规范
12.[标准] 风力发电机组变流系统用机侧滤波器技术规范

发布单位：
中国-行业标准-能源(CN-NB)

标准状态：
现行

标准号：
NB/T 10437-2020

发布时间：
2020-10-23

中标分类：
L18 电子元器件与信息技术 - 电子元件 - 滤波器、延迟线

国标分类：
31.160 电子学 - 滤波器

实施时间：
2021-02-01

摘要：本文件规定了风力发电机组变流系统用机侧滤波器的技术要求、试验方法、检验规则及其产品的相关信息等。本文件适用于连接风力发电机绕组和机侧变流器之间用于滤波功能的组件,包含独立滤波器(外置)和附属于变流器的滤波器〈内置),双馈机组机侧滤波器范围、全功率机组机侧滤波器范围分别见图1和图2
13.[标准] “领跑者”标准评价要求电视

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/CECA-G 0055-2020

发布时间：
2020-08-14

中标分类：
M70 通信、广播 - 广播、电视设备 - 广播、电视设备综合

国标分类：
31.160 电子学 - 滤波器

实施时间：
2020-08-17

摘要：主要技术内容:文件规定了电视产品的“领跑者”标准评价的术语和定义、评价指标体系和评价方法。本文件适用于电视产品企业标准水平评价。电视产品主要功能是接收电视信号并将其转换为图像和声音，可以分为液晶电视、OLED 电视和激光电视。相关机构在制定企业标准“领跑者”评估方案时可参照使用，企业或相关机构在制定企业标准时也可参照使用
14.[标准] 전자기 간섭 억제용 수동 필터 — 제1부: 품목 규격

无源滤波器用于电磁干扰抑制第1部分:通用规范

发布单位：
韩国-韩国标准(KR-KS)

标准状态：
现行

标准号：
KS C IEC 60939-1-2019

发布时间：
2019-11-15

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：

摘要： 이 규격은 주파수가 100 Hz 이하이고 도체 사이의 전 압이 직류, 교류(실효값) 500 V 이하이거나 도체 와 접지 사이의 전압이 직류, 교류(실효값) 250 V 이하의 공칭 전압에 연결된 기구나 기계에 사용되는 전자파 장해 억제용 필터에 적용된다.
15.[标准] 전자기 간섭 억제용 수동 필터 — 제3부: 안전 시험이 적절한 수동 필터

用于电磁干扰抑制的被动滤波单元 - 第3部分:适用于哪些安全测试的被动滤波单元

发布单位：
韩国-韩国标准(KR-KS)

标准状态：
现行

标准号：
KS C IEC 60939-3-2019

发布时间：
2019-11-15

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：

摘要： 이 표준은 전자기 발생원에서 생성되는 원치 않는 고주파 신호(잡음이나 간섭 등의)를 감쇄시키기 위해 사용되는 수동 필터를 다룬다. 이 표준은 하나의 외함 안에 들어 있거나 인쇄 회로 기판에 설치되어 소형의 독립체(entity)를 형성하는 싱글 또는 멀티 채널 필터 모두를 포함한다. 이 표준은 용량성 성분을 사용하여 필터의 구성 내에 인덕턴스가 내재하는 필터에 적용된다. 유사하게, 인덕턴스 소자를 사용하여 필터의 구성 내에 정전 용량이 내재하는 필터 역시 이 표준을 따라야 한다. 주어진 부품이 커패시터, 인덕터 또는 필터 중 어떤 것으로 설계되었는지 밝히는 것은 제조사의 결정에 달려 있다. 필터는 저항기 및/또는 배리스터 또는 그와 유사한 부품 등 다른 부품을 포함할 수 있다. 이 표준은 안전 시험이 적절한 전자기 간섭 억제용 수동 필터에 적용한다. 이것은 이 표준에 명시된 필터는 주 전원에 연결되거나(이 경우, 표 3의 강제 시험 항목에 부합하여야 한다.), 혹은 회로의 다른 부분에서 사용되며 장비 사양에서 일부 혹은 모든 안전 시험이 요구된다고 지시함을 의미한다. 이 표준은 교류 전원 또는 기타 공급선(직류 또는 교류)에 연결되었을 때, 정격 전압이 교류 1 000 V 이하이면서 공칭 주파수 400 Hz 이하이거나, 또는 정격 전압이 직류 1 500 V인 필터에 적용한다.
16.[标准] 人造石英光学低通滤波器晶片

发布单位：
中国-国家标准(CN-GB)

标准状态：
现行

标准号：
GB/T 32988-2016

发布时间：
2016-10-13

中标分类：
L21 电子元器件与信息技术 - 电子元件 - 石英晶体、压电元件

国标分类：
31.160 电子学 - 滤波器

实施时间：
2017-09-01

摘要：本标准规定了人造石英光学低通滤波器晶片术语和定义、分级、要求、测试方法、检验规则及包装、标识、交货条件。本标准适用于人造石英光学低通滤波器晶片。

获取标准
17.[标准] 纤维光学滤波器第1部分：总规范

发布单位：
中国-国家标准计划(CN-PLAN)

标准状态：
正在征求意见

标准号：
20151493-T-339

发布时间：
2015-08-18

中标分类：
L51 电子元器件与信息技术 - 光电子器件 - 激光器件

国标分类：
31.160 电子学 - 滤波器

实施时间：

摘要：本规范规定了纤维光学滤波器的分类。它们是用于选择特定波长的无源器件，包括下列主要特性：a）它们是无源的，因为不含有光电器件或其它换能元件；b）它们放大了频谱强度分布以达到筛选一些波长而抑制另一些波长；c）它们是固定的，如放大频谱强度分布是固定的、不可调的；d）它们对光纤或光纤元件两部分有一个最大的光功率值；e）它们依据其特性不同，可分为以下几种：1）短波长通过式，2）长波长通过式，3）带通式，4）陷波式，也有以上种类组合的可能。本标准确定了下列统一要求：a）光学、机械和环境特性；b）用于合格评定的测量和试验程序
18.[标准] Passive filter units for electromagnetic interference suppression - Part 3: Passive filter units for which safety tests are appropriate

用于电磁干扰抑制的被动滤波单元 - 第3部分:适用于哪些安全测试的被动滤波单元

发布单位：
国际组织-国际电工委员会(IX-IEC)

标准状态：
已修订

标准号：
IEC 60939-3:2015

发布时间：
2015-08-12

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

实施时间：

摘要： IEC 60939-3:2015 covers passive filters used to attenuate unwanted radio-frequency signals (such as noise or interference) generated from electromagnetic sources. Both single and multi-channel filters within one enclosure or which are built on a printed circuit board forming a compact entity are included within the scope of this specification. This specification applies to passive filter units for electromagnetic interference suppression for which safety tests are appropriate. This implies that filters specified according to this specification will either be connected to mains supplies, when compliance with the mandatory tests of Table 3 is necessary, or used in other circuit positions where the equipment specification prescribes that some or all of these safety tests are required. This specification applies to passive filter units, which will be connected to an a.c. mains or other supply (d.c. or a.c.) with a nominal voltage not exceeding 1 000 V a.c., with a nominal frequency not exceeding 400 Hz, or 1 500 V d.c.
19.[标准] 电子元器件质量评定体系规范压电陶瓷陷波器第1部分：总规范鉴定批准

发布单位：
中国-行业标准-电子(CN-SJ)

标准状态：
现行

标准号：
SJ/T 2960.1-2013

发布时间：
2013-10-17

中标分类：
L21 电子元器件与信息技术 - 电子元件 - 石英晶体、压电元件

国标分类：
31.160 电子学 - 滤波器

实施时间：
2013-12-01
20.[标准] Piezoelectric filters of assessed quality - Part 1: Genericspecification

经质量评定的压电滤波器.第1部分:通用规格

发布单位：
国际组织-国际电工委员会(IX-IEC)

标准状态：
现行

标准号：
IEC 60368-1:2000+AMD1:2004 CSV

发布时间：
2013-05-28

中标分类：
-

国标分类：
31.160 电子学 - 滤波器

31.140 电子学 - 频率控制和选择用压电器件与介质器件

实施时间：

摘要： IEC 60268-1:2000+A1:2004 Specifies the methods of test and general requirements for piezoelectric filters of assessed quality using either capability approval or qualification approval procedures.This consolidated version consists of the fourth edition (2000)and its amendment 1 (2004). Therefore, no need to order amendment inaddition to this publication.