力学试验_国内外标准网文献检索下载

1.[标准] 温度-湿度-振动-低气压综合环境试验系统

发布单位：
中国-国家标准(CN-GB)

标准状态：
即将实施

标准号：
GB/T 44279-2024

发布时间：
2024-08-23

中标分类：
N73 机械振动、冲击设备与动平衡机

国标分类：
19.060 力学试验

实施时间：
2025-03-01

摘要：本文件规定了温度-湿度-振动-低气压综合环境试验系统的组成、技术要求、检验规则、标志和包装，描述了温度-湿度-振动-低气压综合环境试验系统的检验方法。
本文件适用于温度-湿度-振动-低气压综合环境试验系统(以下简称“四综合试验系统”)的制造。

获取标准
2.[标准] 三轴同振电动振动试验系统

发布单位：
中国-国家标准(CN-GB)

标准状态：
即将实施

标准号：
GB/T 44401-2024

发布时间：
2024-08-23

中标分类：
N73 机械振动、冲击设备与动平衡机

国标分类：
19.060 力学试验

实施时间：
2025-03-01

摘要：本文件规定了三轴同振电动振动试验系统的基本参数、技术要求、检验规则、标志、包装和随机文件，描述了三轴同振电动振动试验系统的检验方法。本文件适用于三轴同振电动振动试验系统(以下简称“三轴振动系统”)的制造。

获取标准
3.[标准] 电动振动台双台并激振动试验系统

发布单位：
中国-国家标准(CN-GB)

标准状态：
即将实施

标准号：
GB/T 44400-2024

发布时间：
2024-08-23

中标分类：
N73 机械振动、冲击设备与动平衡机

国标分类：
19.060 力学试验

实施时间：
2025-03-01

摘要：本文件规定了电动振动台双台并激振动试验系统的技术要求、检验规则、标志、包装、运输和贮存，描述了电动振动台双台并激振动试验系统的检验方法。本文件适用于电动振动台双台并激振动试验系统(以下简称“双台系统”)的制造。由多个相同方向组成的多台并激的电动振动试验系统参照执行。

获取标准
4.[标准] Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe

测定高密度聚乙烯树脂或高密度聚乙烯波纹管慢速裂纹扩展阻力的缺口恒定连接应力（NCLS）试验的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM F2136-18(2024)

发布时间：
2024-02-01

中标分类：
-

国标分类：
19.060 试验 - 机械试验

83.140.01 橡胶和塑料制品 - 橡胶和塑料制品综合

实施时间：

摘要： 1.1This test method is used to determine the susceptibility of high-density polyethylene (HDPE) resins or corrugated pipe to slow-crack-growth under a constant ligament-stress in an accelerating environment. This test method is intended to apply only to HDPE of a limited melt index (0.947 g/cm3to 0.955 g/cm3). This test method may be applicable for other materials, but data are not available for other materials at this time.1.2This test method measures the failure time associated with a given test specimen at a constant, specified, ligament-stress level.1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4Definitions are in accordance with TerminologyF412, and abbreviations are in accordance with TerminologyD1600, unless otherwise specified.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1This test method does not purport to interpret the data generated.4.2This test method is intended to compare slow-crack-growth (SCG) resistance for a limited set of HDPE resins.4.3This test method may be used on virgin HDPE resin compression-molded into a plaque or on extruded HDPE corrugated pipe that is chopped and compression-molded into a plaque (see7.1.1for details).
5.[标准] Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

规定机械性能和性能检验用紧固件取样的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM F1470-24

发布时间：
2024-01-01

中标分类：
-

国标分类：
19.060 试验 - 机械试验

实施时间：

摘要： 1.1This practice provides sampling methods for determining how many fasteners to include in a random sample in order to determine the acceptability or disposition of a given lot of fasteners.1.2This practice is for mechanical properties, physical properties, performance properties, coating requirements, and other quality requirements specified in the standards of ASTM Committee F16. Dimensional and thread criteria sampling plans are the responsibility of ASME Committee B18.1.3This practice provides for two sampling plans: one designated the “detection process,” as described in TerminologyF1789, and one designated the “prevention process,” as described in TerminologyF1789.1.4This practice is intended to be used as either a Final Inspection Plan for manufacturers, or as a Receiving Inspection Plan for purchasers/users. It is not valid for third-party qualification testing.1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1Sampling shall be selected in a random manner, ensuring that any unit in the lot has an equal chance of being chosen. Sampling should not be localized by selections being taken from the top of a container or from only one container of multi-container lots.4.2The purchaser should be aware of the supplier's quality assurance system. This can be accomplished by auditing the supplier's quality system, if qualified auditors are available, or by third-party assessment certification, such as provided by IATF 16949, or ISO 9001.
6.[标准] 金属材料巴氏硬度试验第2部分：硬度计的检验与校准

发布单位：
中国-国家标准(CN-GB)

标准状态：
现行

标准号：
GB/T 43432.2-2023

发布时间：
2023-11-27

中标分类：
N71 仪器、仪表 - 试验机与无损探伤仪器 - 金属材料试验机

国标分类：
19.060 试验 - 机械试验

实施时间：
2024-06-01

摘要：本文件描述了用直接检验法和间接检验法检验巴氏硬度计（以下简称“硬度计”）的方法，规定了巴氏硬度计的分类、一般要求、直接检验法、间接检验法、检验周期和检验报告等要求。
本文件适用于巴氏硬度计的检验和校准，间接检验法还可独立地用于硬度计使用中的定期常规检验。

获取标准
7.[标准] 金属材料巴氏硬度试验第3部分：标准硬度块的标定

发布单位：
中国-国家标准(CN-GB)

标准状态：
现行

标准号：
GB/T 43432.3-2023

发布时间：
2023-11-27

中标分类：
N71 仪器、仪表 - 试验机与无损探伤仪器 - 金属材料试验机

国标分类：
19.060 试验 - 机械试验

实施时间：
2024-06-01

摘要：本文件规定了按GB/T 43432.2对巴氏硬度计进行间接检验所用的巴氏标准硬度块（以下简称标准块）的标定方法。
本文件适用于巴氏标准硬度块的标定。

获取标准
8.[标准] 电液伺服万能试验机

发布单位：
中国-国家标准(CN-GB)

标准状态：
现行

标准号：
GB/T 16826-2023

发布时间：
2023-11-27

中标分类：
N71 仪器、仪表 - 试验机与无损探伤仪器 - 金属材料试验机

国标分类：
19.060 试验 - 机械试验

实施时间：
2024-06-01

摘要：本文件规定了电液伺服万能试验机的主参数系列、技术要求、检验方法、检验规则、标志与包装等内容。本文件适用于最大试验力不大于10 MN用于金属和非金属材料力学性能试验的电液伺服万能试验机(以下简称试验机)的设计、制造和检验。电液伺服压力试验机的设计、制造和检验参照使用。

获取标准
9.[标准] 金属材料维氏硬度试验第2部分：硬度计的检验与校准

发布单位：
中国-国家标准计划(CN-PLAN)

标准状态：
正在起草

标准号：
20230594-T-604

发布时间：
2023-08-06

中标分类：
-

国标分类：
19.060 试验 - 机械试验

实施时间：
10.[标准] 金属材料维氏硬度试验第3部分：标准硬度块的标定

发布单位：
中国-国家标准计划(CN-PLAN)

标准状态：
正在起草

标准号：
20230595-T-604

发布时间：
2023-08-06

中标分类：
-

国标分类：
19.060 试验 - 机械试验

实施时间：
11.[标准] 电动振动试验系统

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/SZBX 148-2023

发布时间：
2023-11-14

中标分类：
N 仪器、仪表

国标分类：
19.060 试验 - 机械试验

实施时间：
2023-11-15

摘要：范围:本文件适用于试验用电动振动系统;主要技术内容:本文件规定了电动振动试验系统（以下简称振动系统）的系统组成、基本参数、技术要求、检验方法和检验规则等
12.[标准] 热塑性聚丙烯管材耐低温冲击性能试验方法

发布单位：
中国-团体标准(CN-TUANTI)

标准状态：
现行

标准号：
T/WJGY 014-2023

发布时间：
2023-09-25

中标分类：
-

国标分类：
19.060 试验 - 机械试验

实施时间：
2023-10-01

摘要：主要技术内容:原理、设备、试样、状态调节、试验步骤、结果计算和表示以及试验报告
13.[标准] Standard Practice for Verification and Classification of Extensometer Systems

伸长计系统的验证和分类的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM E83-23

发布时间：
2023-01-01

中标分类：
-

国标分类：
19.060 试验 - 机械试验

实施时间：

摘要： 1.1This practice covers procedures for the verification and classification of extensometer systems, but it is not intended to be a complete purchase specification. The practice is applicable only to instruments that indicate or record values that are proportional to changes in length corresponding to either tensile or compressive strain. Extensometer systems are classified on the basis of the magnitude of their errors.1.2Because strain is a dimensionless quantity, this document can be used for extensometers based on either SI or US customary units of displacement.Note 1:Bonded resistance strain gauges directly bonded to a specimen cannot be calibrated or verified with the apparatus described in this practice for the verification of extensometers having definite gauge points. (See procedures as described in Test MethodsE251.)1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
14.[标准] Standard Test Method for Compressive Strength of Masonry Prisms

砖石棱柱抗压强度的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
历史

标准号：
ASTM C1314-23a

发布时间：
2023-06-15

中标分类：
-

国标分类：
19.060 试验 - 机械试验

91.080.30 建筑物结构 - 砖石结构

实施时间：

摘要： 1.1This test method covers procedures for masonry prism construction and testing, and procedures for determining the tested compressive strength of masonry,fmt, used to determine compliance with the specified compressive strength of masonry,f ′m. When this test method is used for research purposes, the construction and test procedures within serve as a guideline and provide control parameters.1.2This test method also covers procedures for determining the compressive strength of prisms obtained from field-removed masonry specimens.1.3The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1This test method provides a means of verifying that masonry materials used in construction result in masonry that meets the specified compressive strength (Note 1).Note 1:A prism is an assembly of components used to measure or verify a property (in this case, the specified compressive strength of masonry,f 'm). Testing of prisms may be part of a project’s field quality control or assurance program. In these cases, prisms are built as companions to a masonry element (for example, a masonry wall, column, pilaster, beam, or other element) at a jobsite where the masonry element is site-constructed, or within a factory or shop where the element is shop-built. These prisms are not intended to replicate or model the performance or design attributes of the as-built element. Prisms may also be fabricated in a laboratory for research purposes (Appendix X2). In each scenario (field or research) the test procedures are structured so that masonry assembly tested compressive strength (fmt) is measured in an accurate and repeatable manner.4.2This test method provides a means of evaluating compressive strength characteristics of in-place masonry construction through testing of prisms obtained from that construction when sampled in accordance with PracticeC1532/C1532M. Decisions made in preparing such field-removed prisms for testing, determining the net area, and interpreting the results of compression tests require professional judgment.4.3If this test method is used as a guideline for performing research to determine the effects of various prism construction or test parameters on the compressive strength of masonry, deviations from this test method shall be reported. Such research prisms shall not be used to verify compliance with a specified compressive strength of masonry.Note 2:The testing laboratory performing this test method should be evaluated in accordance with PracticeC1093.4.3.1Appendix X2includes guidance information for the researcher on aspects of materials, construction, and analysis.
15.[标准] Standard Test Method for Compressive Strength of Masonry Prisms

砖石棱柱抗压强度的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM C1314-23b

发布时间：
2023-12-01

中标分类：
-

国标分类：
19.060 试验 - 机械试验

91.080.30 建筑物结构 - 砖石结构

实施时间：

摘要： 1.1This test method covers procedures for masonry prism construction and testing, and procedures for determining the tested compressive strength of masonry,fmt, used to determine compliance with the specified compressive strength of masonry,f ′m. When this test method is used for research purposes, the construction and test procedures within serve as a guideline and provide control parameters.1.2This test method also covers procedures for determining the compressive strength of prisms obtained from field-removed masonry specimens.1.3The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.4The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1This test method provides a means of verifying that masonry materials used in construction result in masonry that meets the specified compressive strength (Note 1).Note 1:A prism is an assembly of components used to measure (in this case, the tested compressive strength of masonry,fmt) or verify a property (in this case, the specified compressive strength of masonry,f 'm). Testing of prisms may be part of a project’s field quality control or assurance program. In these cases, prisms are built as companions to a masonry element (for example, a masonry wall, column, pilaster, or beam) at a jobsite where the masonry element is site-constructed, or within a factory or shop where the element is shop-built. While these prisms can be used to determine compliance with the specified compressive strength of masonry,f 'm, they are not intended to replicate or model all of the performance or design attributes of the as-built element. Prisms may also be fabricated in a laboratory for research purposes (Appendix X2). In each scenario (field or research) the test procedures are structured so that masonry assembly tested compressive strength (fmt) is measured in an accurate and repeatable manner.4.2This test method provides a means of evaluating compressive strength characteristics of in-place masonry construction through testing of prisms obtained from that construction when sampled in accordance with PracticeC1532/C1532M. Decisions made in preparing such field-removed prisms for testing, determining the net area, and interpreting the results of compression tests require professional judgment.4.3If this test method is used as a guideline for performing research to determine the effects of various prism construction or test parameters on the compressive strength of masonry, deviations from this test method shall be reported. Such research prisms shall not be used to verify compliance with a specified compressive strength of masonry.Note 2:The testing laboratory performing this test method should be evaluated in accordance with PracticeC1093.4.3.1Appendix X2includes guidance information for the researcher on aspects of materials, construction, and analysis.
16.[标准] Standard Guide for Statistical Analysis of Linear or Linearized Stress-Life (emph type='bdit'S-N/emph) and Strain-Life (ε-emph type='bdit' N/emph) Fatigue Data (Withdrawn 2024)

线性或线性化应力寿命（emph type=“bdit”S-N/emph）和应变寿命（ε-emph type=“bditN/emph）疲劳数据统计分析标准指南

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
作废

标准号：
ASTM E739-23

发布时间：
2023-02-01

中标分类：
-

国标分类：
19.060 试验 - 机械试验

实施时间：

摘要： 1.1This guide covers onlyS-Nand ε-Nrelationships that may be reasonably approximated by a straight line (on appropriate coordinates) for a specific interval of stress or strain. It presents elementary procedures that presently reflect good practice in modeling and analysis. However, because the actualS-Nor ε-Nrelationship is approximated by a straight line only within a specific interval of stress or strain, and because the actual fatigue life distribution is unknown, it isnot recommendedthat (a) theS-Nor ε-Ncurve be extrapolated outside the interval of testing, or (b) the fatigue life at a specific stress or strain amplitude be estimated below approximately the fifth percentile (P≃0.05). As alternative fatigue models and statistical analyses are continually being developed, later revisions of this guide may subsequently present analyses that permit more complete interpretation ofS-Nand ε-Ndata.1.2This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1Materials scientists and engineers are making increased use of statistical analyses in interpretingS-Nand ε-Nfatigue data. Statistical analysis applies when the given data can be reasonably assumed to be a random sample of (or representation of) some specific defined population or universe of material of interest (under specific test conditions), and it is desired either to characterize the material or to predict the performance of future random samples of the material (under similar test conditions), or both.
17.[标准] Standard Terminology Relating to Methods of Mechanical Testing

与机械试验方法有关的标准术语

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
历史

标准号：
ASTM E6-23

发布时间：
2023-01-15

中标分类：
-

国标分类：
01.040.19 词汇 - 试验 (词汇)

19.060 试验 - 机械试验

实施时间：

摘要： 1.1This terminology covers the principal terms relating to methods of mechanical testing of solids. The general definitions are restricted and interpreted, when necessary, to make them particularly applicable and practicable for use in standards requiring or relating to mechanical tests. These definitions are published to encourage uniformity of terminology in product specifications.1.2Terms relating to fatigue and fracture testing are defined in TerminologyE1823.1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
18.[标准] Standard Terminology Relating to Methods of Mechanical Testing

与机械试验方法有关的标准术语

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM E6-23a

发布时间：
2023-02-01

中标分类：
-

国标分类：
01.040.19 词汇 - 试验 (词汇)

19.060 试验 - 机械试验

实施时间：

摘要： 1.1This terminology covers the principal terms relating to methods of mechanical testing of solids. The general definitions are restricted and interpreted, when necessary, to make them particularly applicable and practicable for use in standards requiring or relating to mechanical tests. These definitions are published to encourage uniformity of terminology in product specifications.1.2Terms relating to fatigue and fracture testing are defined in TerminologyE1823.1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
19.[标准] Standard Practices for Cycle Counting in Fatigue Analysis

疲劳分析中循环计数的标准实施规程

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM E1049-85(2023)

发布时间：
2023-11-01

中标分类：
-

国标分类：
19.060 试验 - 机械试验

实施时间：

摘要： 1.1These practices are a compilation of acceptable procedures for cycle-counting methods employed in fatigue analysis. This standard does not intend to recommend a particular method.1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1Cycle counting is used to summarize (often lengthy) irregular load-versus-time histories by providing the number of times cycles of various sizes occur. The definition of a cycle varies with the method of cycle counting. These practices cover the procedures used to obtain cycle counts by various methods, including level-crossing counting, peak counting, simple-range counting, range-pair counting, and rainflow counting. Cycle counts can be made for time histories of force, stress, strain, torque, acceleration, deflection, or other loading parameters of interest.
20.[标准] Standard Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate

集料体积密度（“单位重量”）和空隙的标准试验方法

发布单位：
美国-美国材料与试验协会(US-ASTM)

标准状态：
现行

标准号：
ASTM C29/C29M-23

发布时间：
2023-10-01

中标分类：
-

国标分类：
19.060 试验 - 机械试验

实施时间：

摘要： 1.1This test method covers the determination of bulk density (“unit weight”) of aggregate in a compacted or loose condition, and calculated voids between particles in fine, coarse, or mixed aggregates based on the same determination. This test method is applicable to aggregates not exceeding 125 mm [5 in.] in nominal maximum size.Note 1:Unit weight is the traditional terminology used to describe the property determined by this test method, which is weight per unit volume (more correctly, mass per unit volume or density).1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard, as appropriate for a specification with which this test method is used. An exception is with regard to sieve sizes and nominal size of aggregate, in which the SI values are the standard as stated in SpecificationE11. Within the text, inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. ====== Significance And Use ======4.1This test method is often used to determine bulk density values that are necessary for use for many methods of selecting proportions for concrete mixtures.4.2The bulk density also may be used for determining mass/volume relationships for conversions in purchase agreements. However, the relationship between degree of compaction of aggregates in a hauling unit or stockpile and that achieved in this test method is unknown. Further, aggregates in hauling units and stockpiles usually contain absorbed and surface moisture (the latter affecting bulking), while this test method determines the bulk density on a dry basis.4.3A procedure is included for computing the percentage of voids between the aggregate particles based on the bulk density determined by this test method.