首页> 外文OA文献 >Molar heat capacity (Cv) for saturated and compressed liquid and vapor nitrogen from 65 to 300 K at pressures to 35 Mpa

【2h】

Molar heat capacity (Cv) for saturated and compressed liquid and vapor nitrogen from 65 to 300 K at pressures to 35 Mpa

机译：摩尔热容量（CV）用于饱和和压缩液体和蒸汽氮，在压力下为35至300 k至35MPa

代理获取

本网站仅为用户提供外文OA文献查询和代理获取服务，本网站没有原文。下单后我们将采用程序或人工为您竭诚获取高质量的原文，但由于OA文献来源多样且变更频繁，仍可能出现获取不到、文献不完整或与标题不符等情况，如果获取不到我们将提供退款服务。请知悉。

页面导航

著录项
引文网络
相似文献
相关主题

著录项

作者
J.W. Magee;
展开▼
作者单位

展开▼
年度 1991
总页数
原文格式 PDF
正文语种
中图分类

相似文献

外文文献
中文文献
专利

1. Heat Capacity of Saturated and Compressed Liquid Dimethyl Ether at Temperatures from (132 to 345) K and at Pressures to 35 MPa [J] . Wu Jiangtao, Magee Joseph W. Journal of Chemical and Engineering Data: the ACS Journal for Data . 2018,第5期

机译：饱和和压缩液体二甲醚的热容量在（132-345）K和压力下至35MPa的温度下
2. Apparent molar volumes and apparent molar heat capacities of aqueous tetrahydrofuran, dimethyl sulfoxide, 1,4-dioxane, and 1,2-dimethoxyethane at temperatures from 278.15 K to 393.15 K and at the pressure 0.35 MPa [J] . D.M. Swenson, M.B. Blodgett, S.P. Ziemer, The Journal of Chemical Thermodynamics . 2008,第2期

机译：在278.15 K至393.15 K的温度和0.35 MPa的压力下，四氢呋喃，二甲亚砜，1,4-二恶烷和1,2-二甲氧基乙烷的表观摩尔体积和表观摩尔热容量
3. Apparent molar volumes and apparent molar heat capacities of aqueous KI, HIO3, NaIO3, and KIO3 at temperatures from 278.15 K to 393.15 K and at the pressure 0.35 MPa [J] . D.M. Swenson, E.M. Woolley The Journal of Chemical Thermodynamics . 2008,第1期

机译：KI，HIO3，NaIO3和KIO3水溶液在278.15 K至393.15 K的温度和0.35 MPa的压力下的表观摩尔体积和表观摩尔热容量
4. Effect of surface conditions on pool bo8iling critical heat fluxes in saturated and subcooled liquid nitrogen at various pressures [C] . A. Saurai, M. Shiotsu, K. Hata, Cryogenic engineering conference . 1998

机译：各种压力下饱和和过冷液氮中池Bo1临界热通量的表面条件的影响
5. Amino acids under hydrothermal conditions: Apparent molar volumes, apparent molar heat capacities, and acid /base dissociation constants for aqueous alpha-alanine, beta-alanine, glycine, and proline at temperatures from 25 to 250°C and pressures up to 30.0 MPa. [D] . Clarke, Rodney George Francis. 2000

机译：水热条件下的氨基酸：在25至250°C的温度和最高30.0 MPa的压力下，水性α-丙氨酸，β-丙氨酸，甘氨酸和脯氨酸的表观摩尔体积，表观摩尔热容量和酸/碱解离常数。
6. Molar Heat Capacity (Cv) for Saturated and Compressed Liquid and Vapor Nitrogen from 65 to 300 K at Pressures to 35 MPa [O] . J. W. Magee 1991

机译：压力至35 MPa时饱和和压缩的液态氮和蒸气氮的摩尔热容（Cv）从65至300 K
7. Mechanical properties of various concrete after high temperature exposure Mechanical property of various types of concrete after high temperature exposure is investigated. Considering compressive strength requirement for a vertical element in high rise building, concrete specimens with various design strengths of 35, 80, 100, and 150 MPa were tested. Particularly, the influence of incorporated steel fiber on fire resistance is of interest in this study. Experimental results show that the fire resistance depends on the design strength and steel fiber content. Normal strength concrete (NSC) of a design strength of 35 MPa or high performance concrete (HPC) of 80-100 MPa does not spall when exposed to 100-400 °C of temperature. However, an explosive spalling occurs at 300 °C when the HPCs contain 1 vol. of steel fiber. Ultra-high performance concrete (UHPC) of a design strength of 150 MPa and 1.5 vol. of steel fiber also shows dramatic spalling at 300 °C. The experimental results found in this study can contribute to a better understanding of the behaviors of HPC and UHPC under fire and the role of steel fiber on the fire resistance. [O] . 2017

机译：研究了高温暴露后各种混凝土高温曝光机械性能各种混凝土的机械性能。考虑到高层建筑中垂直元件的抗压强度要求，测试了35,80,100和150MPa各种设计强度的混凝土试样。特别是，在这项研究中，掺入钢纤维对耐火性的影响。实验结果表明，耐火性取决于设计强度和钢纤维含量。在暴露于100-400°C的温度时，80-100MPa的设计强度为35MPa或高性能混凝土（HPC）的正常强度混凝土（NSC）不会击落。然而，当HPC含有1体积的钢纤维的百分比时，爆炸性剥落发生在300℃。超高性能混凝土（UHPC）的设计强度为150 MPa和1.5 Vol。钢纤维的百分比也显示出300℃的剧烈剥落。本研究中发现的实验结果可以有助于更好地了解在火灾中的HPC和UHPC的行为以及钢纤维对耐火性的作用。

Molar heat capacity (Cv) for saturated and compressed liquid and vapor nitrogen from 65 to 300 K at pressures to 35 Mpa

著录项

引文网络

相似文献

相关主题

期刊订阅