首页> 外文OA文献 >On the analysis of chip shaping after finishing turning of Ti6Al4V titanium alloy under dry, wet and MQL conditions

【2h】

On the analysis of chip shaping after finishing turning of Ti6Al4V titanium alloy under dry, wet and MQL conditions

机译：干燥，潮湿和MQL条件下Ti6Al4V钛合金完成后芯片成型分析

代理获取

本网站仅为用户提供外文OA文献查询和代理获取服务，本网站没有原文。下单后我们将采用程序或人工为您竭诚获取高质量的原文，但由于OA文献来源多样且变更频繁，仍可能出现获取不到、文献不完整或与标题不符等情况，如果获取不到我们将提供退款服务。请知悉。

页面导航

著录项
引文网络
相似文献
相关主题

著录项

作者
Kamil Leksycki; Eugene Feldshtein;
展开▼
作者单位

展开▼
年度 2019
总页数
原文格式 PDF
正文语种
中图分类

相似文献

外文文献
中文文献
专利

1. Cutting Parameter Optimization in Finishing Milling of Ti-6Al-4V Titanium Alloy under MQL Condition using TOPSIS and ANOVA Analysis [J] . V.C.Nguyen, T.D.Nguyen, D.H.Tien Engineering Technology and Applied Science Research . 2021,第1期

机译：用TOPSIS和ANOVA分析在MQL条件下完成Ti-6AL-4V钛合金完成铣削参数优化
2. Wear performance of (nc-AlTiN)/(a-Si_3N_4) coating and (nc-AlCrN)/(a-Si_3N_4) coating in high-speed machining of titanium alloys under dry and minimum quantity lubrication (MQL) conditions [J] . Zhiqiang Liu, Qinglong An, Jinyang Xu, Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear . 2013,第1a2期

机译：在干和最小量润滑（MQL）条件下高速加工钛合金时（nc-AlTiN）/（a-Si_3N_4）涂层和（nc-AlCrN）/（a-Si_3N_4）涂层的磨损性能
3. Multi-objective optimization of turning titanium-based alloy Ti-6Al-4V under dry, wet, and cryogenic conditions using gray relational analysis (GRA) [J] . Khan Muhammad Ali, Jaffery Syed Husain Imran, Khan Mushtaq, The International Journal of Advanced Manufacturing Technology . 2020,第9a10期

机译：使用灰色关系分析（GRA）在干燥，湿，低温条件下转动钛基合金Ti-6Al-4V的多目标优化
4. The Surface Texture of Ti6Al4V Titanium Alloy Under Wet and Dry Finish Turning Conditions [C] . Kamil Leksycki, Eugene Feldshtein Conference on Machining and Abrasive Machining . 2020

机译：Ti6Al4V钛合金的表面纹理湿润干燥完成转动条件
5. Computational analysis of micromachining Ti6Al4V titanium alloy . [D] . Novakov, Tamara. 2010

机译：Ti6Al4V钛合金微加工的计算分析。
6. Investigation on Wear Behavior of Cryogenically Treated Ti-6Al-4V Titanium Alloy under Dry and Wet Conditions [O] . Yonggang Li, Xingfu Wang, Shengqiang Yang, 2019

机译：深冷处理的Ti-6Al-4V钛合金在干湿条件下的磨损行为研究
7. Analysis of the effect of the machining surface roughness and form chips of titanium alloy Ti6Al4V [O] . Marek Kołodziej, Paweł Karolczak 2016

机译：钛合金Ti6Al4V加工表面粗糙度和芯片的效果分析
8. Effect of grinding on the fatigue life of titanium alloy (5 Al-2.5 Sn) under dry and wet conditions [R] . Rangaswamy, Partha, Terutung, Hendra, Jeelani, Shaik 1989

机译：研磨对干燥和潮湿条件下钛合金（5 al-2.5 sn）疲劳寿命的影响

On the analysis of chip shaping after finishing turning of Ti6Al4V titanium alloy under dry, wet and MQL conditions

著录项

引文网络

相似文献

相关主题

期刊订阅