首页> 外文OA文献 >A Study on Strength of Toothed Belt : 3rd Report, Fatigue Strength and Features of Fracture under Uniform Transmissive Load

【2h】

A Study on Strength of Toothed Belt : 3rd Report, Fatigue Strength and Features of Fracture under Uniform Transmissive Load

机译：齿带强度研究：第三次报告，疲劳率下裂缝的疲劳强度和特征

代理获取

本网站仅为用户提供外文OA文献查询和代理获取服务，本网站没有原文。下单后我们将采用程序或人工为您竭诚获取高质量的原文，但由于OA文献来源多样且变更频繁，仍可能出现获取不到、文献不完整或与标题不符等情况，如果获取不到我们将提供退款服务。请知悉。

页面导航

著录项
引文网络
相似文献
相关主题

著录项

作者
Tomio KOYAMA; Masanori KAGOTANI; Toshinobu SHIBATA; Susumu SATO; Takeshi HOSHIRO;
展开▼
作者单位

展开▼
年度 1978
总页数
原文格式 PDF
正文语种
中图分类

相似文献

外文文献
中文文献
专利

1. Strength and fracture in undermatched joint by dynamic loading - studies on characteristics of dynamic deformation and fracture in welded joint with strength heterogeneity (report 2) [J] . Mochizuki Masahito, An Gyu-Baek, Ohmura Takeshi, Welding Research Abroad . 2001,第12期

机译：动态载荷作用下欠配合接头的强度和断裂-强度不均一的焊接接头动态变形和断裂特性研究（报告2）
2. Basic Experimental Studies of the Local Buckling Strength of Carbon Steel Square Pipes with a Circular Hole Subjected to an Eccentric Axial Compressive Load (3rd Report, In the Case of Eccentric Load at the Upper End and Axial One at the Lower End) [J] . Toshiyuki KITAZAWA 日本機械学会論文集. A編 . 1999,第636期

机译：带有偏心轴向压缩载荷的圆孔碳钢方管局部屈曲强度的基础实验研究（第三次报告，上端为偏心载荷而下端为轴心载荷）
3. Fatigue mechanism of a coating film under rolling contact loading: Study of methods for evaluation of rolling contact fatigue strength of coating films (1st Report) [J] . A IZUWA, M NITTA, M TOYOTA Welding international . 1995,第9期

机译：滚动接触载荷下涂膜的疲劳机理：评估涂膜滚动接触疲劳强度的方法的研究（第一份报告）
4. Improvement of fatigue strength of high tensile strength steel sheet with a pierced hole by coining third report: a study on the mechanism for introduction of compressive residual stress [C] . Eiichi Tamura, Masaaki Miura, Tetsuo Soshiroda, Society of Automotive Engineers of Japan Annual Congress . 2002

机译：用刺穿第三次报告改进高抗拉强度钢板疲劳强度的疲劳强度：施加压缩残余应力引入机制的研究
5. Fracture strength of all-ceramic restorations after fatigue loading [D] . Baladhandayutham, Balasudha. 2011

机译：疲劳载荷后全瓷修复体的断裂强度
6. Principal Features of Fatigue and Residual Strength of Composite Materials Subjected to Constant Amplitude (CA) Loading [O] . Alberto D’Amore, Luigi Grassia 2019

机译：恒定振幅（CA）载荷下复合材料的疲劳和残余强度的主要特征
7. A Study on Strength of Toothed Belt : 1st Report, Load Distribution on Belt Tooth [O] . Tomio KOYAMA, Kozo MURAKAMI, Hajime NAKAI, 1978

机译：齿带强度的研究：第1次报告，皮带齿的负载分布
8. FATIGUE STRENGTHS OF AIRCRAFT MATERIALS AXIAL-LOAD FATIGUE TESTS ON EDGE-NOTCHED SHEET SPECIMENS OF 2024-T3 AND 7075-T6 ALUMINUM ALLOYS AND OF SAE 4130 STEEL WITH NOTCH RADⅡOF 0.004 AND 0.070 INCH [R] . H. J. Grover, W. S. Hyler, L. R. Jackson 1959

机译：2024-T3和7075-T6铝合金边缘板材以及saE 4130钢的轴向负荷疲劳试验的疲劳强度，缺口尺寸为0.004和0.070英寸

A Study on Strength of Toothed Belt : 3rd Report, Fatigue Strength and Features of Fracture under Uniform Transmissive Load

著录项

引文网络

相似文献

相关主题

期刊订阅