...
首页> 外文期刊>Energy Conversion & Management >On the number of PV modules in series for large-power irrigation systems
【24h】

On the number of PV modules in series for large-power irrigation systems

机译:关于大功率灌溉系统的光伏组件串联数量

获取原文
获取原文并翻译 | 示例
           

摘要

Large-power PV irrigation systems (PVIS) from 40 kWp to 1 MWp are increasingly being introduced onto the market since the main technical barriers have been removed and some real-scale demonstrators have shown cost savings up to 80% when compared with the electricity costs from the grid or diesel generators. The electricity compatibility between the PV generator and the frequency converter limits the number of PV modules in series to keep the PV generator voltage below the maximum input voltage of the frequency converter. This limitation can produce losses in terms of PV production and water pumped. As the maximum voltage delivered by the PV generator depends, among others, on the solar cell temperature, some electronic devices are being offered in the market to change the number of PV modules in series depending on this temperature, but they are complex and reduce the reliability of the system. This complexity is not justified because an in-depth analysis of the actual impact of these losses has never been carried out. This paper analyses and quantifies these PV energy losses for the two main applications in the market (pumping to a water pool at a variable frequency, and direct pumping to the irrigation network at constant power) which have different mechanisms of losses, and for locations with different typical meteorological years. The results show that, in the case of pumping to a water pool, the losses are irrelevant if the maximum yearly mean ambient temperature of the location is less than 21.5 degrees C and the voltage required by the pump is less than 568 V. In the case of constant power pumping, the losses are irrelevant if the mentioned temperature is less than 25.8 degrees C and the grid voltage is less than 587 V. In the rest of the cases, the losses are minimized just adding one more PV module in series. As a result, a general methodology to help designers selecting the number of PV modules in series in PV irrigation systems is presented.
机译:由于消除了主要的技术障碍,从40 kWp到1 MWp的大功率PV灌溉系统(PVIS)越来越多地投放市场,并且与电力成本相比,一些实际规模的演示者已显示出高达80%的成本节省来自电网或柴油发电机。 PV发电机和变频器之间的电兼容性限制了串联的PV模块的数量,以使PV发电机电压保持在变频器的最大输入电压以下。这种限制可能会导致光伏发电和抽水方面的损失。由于PV发电机提供的最大电压尤其取决于太阳能电池的温度,因此市场上提供了一些电子设备来根据该温度改变串联的PV模块的数量,但是它们很复杂并降低了温度。系统的可靠性。这种复杂性是没有道理的,因为从未对这些损失的实际影响进行深入分析。本文分析和量化了市场上两个主要应用的光伏能量损耗(以可变频率抽水到水池,以恒定功率直接抽水到灌溉网络),它们具有不同的损耗机理,并且在有不同的典型气象年。结果表明,在泵送至水池的情况下,如果该位置的年平均最高环境温度小于21.5摄氏度且泵所需的电压小于568 V,则损失无关紧要。在恒定功率抽运的情况下,如果上述温度低于25.8摄氏度且电网电压低于587 V,则损耗是无关紧要的。在其余情况下,只需串联增加一个PV组件即可将损耗降至最低。结果,提出了一种通用方法,可帮助设计人员选择光伏灌溉系统中串联的光伏模块数量。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号