...
首页> 外文期刊>Waste Management >A combination of ammonia stripping and low temperature thermal pre-treatment improves anaerobic post-digestion of the supernatant from organic fraction of municipal solid waste treatment
【24h】

A combination of ammonia stripping and low temperature thermal pre-treatment improves anaerobic post-digestion of the supernatant from organic fraction of municipal solid waste treatment

机译:氨气汽提和低温热预处理相结合可改善市政固体废物处理有机部分中上清液的厌氧后消化

获取原文
获取原文并翻译 | 示例
           

摘要

Municipal Solid Waste is mostly composed of organic material which is often treated in anaerobic reactors in waste treatment plants. In most cases, the obtained digestate undergoes a solid/liquid separation step, producing a liquid fraction (known as anaerobic supernatant) rich in ammonium nitrogen that has to be further treated in order to meet discharge standards. The objective of the present work was to evaluate the feasibility of anaerobic post-digestion (37 degrees C) of a supernatant rich in carbon and nitrogen from a municipal waste treatment plant. In order to increase the efficiency of the process, a combined pre-treatment consisting of a low-temperature thermal process (75 degrees C) and ammonia stripping (1.3 L-air L-supernatant(-1) min(-1)) was applied. The effects of pre-treatment contact time (4 and 8 h) and the hydraulic retention time (HRT) in the anaerobic reactor (20-40 d) were studied. Supernatant pretreatment with 8-h contact time caused 13% organic matter solubilisation, thus improving methanisation by 18% when the HRT was 40 d. At the same time, ammonia stripping allowed to maintain ammonia concentration in the digester below inhibitory values (less than 100 mg N-NH3 L-1) enabling therefore high methanogenic activity (0.23 g COD g(-1) VS d(-1)). The final effluent characteristics (low total ammonia nitrogen and aerobically biodegradable organic matter levels) would permit implementing subsequent less energy intensive and more environmental-friendly technologies (such as partial nitritation/anammox) to comply with discharge limits. (C) 2018 Elsevier Ltd. All rights reserved.
机译:城市固体废物主要由有机材料组成,通常在废物处理厂的厌氧反应器中进行处理。在大多数情况下,获得的消化物会经历固/液分离步骤,产生富含氨氮的液体馏分(称为厌氧上清液),必须对其进行进一步处理以满足排放标准。本工作的目的是评估厌氧消化后(37摄氏度)来自城市废物处理厂的富含碳和氮的上清液的可行性。为了提高该过程的效率,组合了预处理过程,该过程包括低温热处理(75摄氏度)和氨气汽提(1.3 L-空气L-上清液(-1)min(-1))。应用。研究了厌氧反应器中预处理接触时间(4和8 h)和水力停留时间(HRT)(20-40 d)的影响。接触时间为8小时的上清液预处理可将有机物溶解度提高13%,从而在HRT为40 d时将甲烷化率提高18%。同时,氨气汽提可以将消化池中的氨气浓度保持在抑制值以下(小于100 mg N-NH3 L-1),从而具有很高的产甲烷活性(> 0.23 g COD g(-1)VS d(-1) ))。最终的出水特性(总氨氮低,需氧可生物降解的有机物含量低)将允许随后实施能耗更低,环境更友好的技术(例如部分硝化/厌氧氨氮)以符合排放限值。 (C)2018 Elsevier Ltd.保留所有权利。

著录项

相似文献

  • 外文文献
  • 中文文献
  • 专利
获取原文

客服邮箱:kefu@zhangqiaokeyan.com

京公网安备:11010802029741号 ICP备案号:京ICP备15016152号-6 六维联合信息科技 (北京) 有限公司©版权所有
  • 客服微信

  • 服务号